Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Test the System 
4-13 LED Indicators 
4
Figure 4-1. Circuit Pack LEDs
DS1 Converter Circuit Pack LEDs
Eleven LEDs p rovide an indic ation of the state of the TN1654 DS1 Converter 
c irc uit p ac k and  the T1/E1 fac ilities. The top  g roup  has the standard  red, g reen 
and  yellow LEDs. The red  LED ind ic ates an alarm c ond ition and the g reen LED 
indic ates testing  in p rog ress. The 4 SPAN...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Test the System 
4-14 LED Indicators 
4
The yellow LED is used  to ind ic ate the state of the fib er interfac e, the fib er 
c hannel, the c ontrol c hannel, and  the c ommunic ations link to the SPE in the 
following manner and order of priority. See Ta b l e  4 - 2
.
SPAN LEDs
The 4 SPAN LEDs ind ic ate the status of the 4 T1/E1 fac ilities. A SPAN LED is in 
one of the following  states:
1....

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Test the System 
4-15 LED Indicators 
4
Figure 4-2. TN1654 DS1 Converter Circuit Pack LEDs
LEDs on Standby Components
In hig h and  c ritic al reliab ility systems, dup lic ated  c omp onents on stand b y usually 
have the yellow LEDs off, with the following  exc ep tions:
nTh e  m a jo r ,  m in o r  a n d  w a r n i n g  a la r m  L ED s o n  t h e  SYSAM  c i rc u i t  p a c k o n  
the stand b y...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Test the System 
4-16 LED Indicators 
4 

Install and Wire Telephones and Other Equipment 
5-1  
5
DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
5
Install and Wire Telephones and
Other Equipment
The wiring procedures are the same for most telephones and other equipment. 
This chapter provides wiring examples of these similar installation procedures. 
These are examples only and actual wiring procedures may differ at each site. 
Wiring pinouts for circuit packs mentioned in this chapter...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-2  
5
Figure 5-1. Punch-downs for Common Circuit Packs
widfccf2 EWS 102798
4
1101941322 21120
51423 3122161524918
71625817
Port Tie Trunk Port MET Line
4
4 Port Tie Trunk
w/ E&M Signaling
Port Data Line 8
Port Digital 8
Port BRI 12Port Hybrid 8Port DID 8
Port Analog
Port CO 8
8
110 19
413
22 21120
5
1423 3
12 21 615
24 918
716 25 8
17
Port Digital...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-3  
5
Telephone Connection Example
The 302C Attendant Console is used as an example telephone connection. This is 
typical of the 603E, 84xx (4-wire), and 94xx telephones. The maximum cabling 
distance for a console powered from the cabinet is 350 feet (100 meters) using 24 
AWG (#5) (0.26 mm
2) wire. The general steps to connect a telephone are:...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-4  
5
Connect Adjunct Power
The attendant console requires -48 VDC adjunct power from pins 7 and 8 of the 
information outlet. Only 3 consoles can be powered by the cabinet from the AUX 
connector. Power the primary console from the cabinet so it has the same power 
failure backup as the system. 
1. For terminals need ing  ad junc t p ower, wire -48...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-5 Analog Station or 2-Wire Digital Station Example 
5
Adjunct power can be provided from the equipment room or equipment closet with 
an 1145B power unit. See ‘‘
1145B Power Supply’’ on page 5-46.
Adjunct power can also be provided locally at the telephone or console with a 
1151A1 or 1151A2 power unit. See ‘‘
1151A1 Power Supply’’ on page 5-55....

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-6 Analog Tie Trunk Example 
5
Analog Tie Trunk Example
This example shows how to connect analog tie trunk wiring from one DEFINITY 
System to another DEFINITY System.
Figure 5-5. Analog Tie Trunk Wiring
1. Set the option switc hes on the p ort c irc uit p ac k (TN760) as d esc rib ed  in 
Appendix B, ‘‘
Op tion Switc h Setting s’’.
2. Install c...