Kyocera TASKalfa 552ci User Manual

Default Setting (System Menu)
8-41
8
Printing Reports/Sending Notice
Print reports to check the machine settings and status. Default settings for printing the result reports can also 
be configured. 
NOTE: If user login administration is enabled, you can only print by logging in with administrator privileges.
Printing Reports
Printable reports are as follows.
Status Page
Check the information including current settings, available memory space, and optional equipment installed.
Font List
Check the font...

Default Setting (System Menu)
8-42 Network Status Page 
Check the information including network interface firmware version, network address and protocol.
Service Status Page
More detailed information is available than on the Status Page. Service personnel usually print the service status 
pages for maintenance purpose.
Use the procedure below to print a report.
1Press the System Menu key.
2Press [Report] and [Next] of Print Report.
3Press [Print] for the report you want to print. Printing starts.
A...

Default Setting (System Menu)
8-43
8
Report for Job Canceled before Sending
Print a send result report when the job is canceled before being sent.
1Press the System Menu key.
2Press [Report], [Next] of Result Report Setting, [Next] of Send Result Report and then [Change] of 
Canceled before Sending.
3Press [Off], [On]. 
4Press [OK].
Downloaded From ManualsPrinter.com Manuals 

Default Setting (System Menu)
8-44
Adjustment/Maintenance
Adjust printing quality and conduct machine maintenance. 
• Copy Density Adjustment …8-44
• Send/Box Density Adjust …8-45
• Drum Refresh …8-45
• Correcting Fine Black Lines …8-46
• System Initialization …8-46
• Display Brightness …8-46
• Silent Mode …8-47
• Auto Color Correction...8-47
• Color Registration...8-47
• Color Calibration Cycle...8-50
• Gray Adjustment...8-51
• Color Calibration...8-52
• Developer Refresh...8-53
• Laser Scanner...

Default Setting (System Menu)
8-45
8
Send/Box Density Adjust
Adjust scan density when sending or storing the data in Document Box. Adjustment can be made in 7 levels 
both in auto and manual density modes.
Use the procedure below to adjust the density.
1Press the System Menu key.
2Press [ ], [Adjustment/Maintenance] and then [Next] of Send/Box Density Adjust..
3Press [Change] of Auto or of Manual.
4Press [-3] - [+3] (Lighter-Darker) to adjust density.
5Press [OK].
Drum Refresh
Refresh the drum when image...

Default Setting (System Menu)
8-46
Correcting Fine Black Lines
Correct fine black lines (black streaks caused by contamination), which may appear on the copies, when the 
optional document processor used. 
The table below shows the available settings.
NOTE: Using Correcting Fine Black Line can impair reproduction of fine characters. It is recommended to 
keep the default ([Off]).
Use the procedure below to specify the setting for correcting fine black lines.
1Press the System Menu key.
2Press [ ],...

Default Setting (System Menu)
8-47
8
2Press [ ], [Adjustment/Maintenance] and then [Change] of Display Brightness.
3Press [1] - [4] (Darker- Lighter) to adjust brightness.
4Press [OK].
Silent Mode
Make the machine run more quietly. Select this mode when the running noise is uncomfortable. 
Use the procedure below to set Silent mode.
1Press the System Menu key.
2Press [ ], [Adjustment/Maintenance] and then [Change] of Silent Mode.
3Press [Off] or [On].
4Press [OK].
Auto Color Correction
This setting...

Default Setting (System Menu)
8-48
1Press the System Menu key.
2Press [ ], [Adjustment/Maintenance], [ ] and 
then [Next] of Color Registration.
3Press [Print] of Chart. A chart is printed.
On the chart, for each of M (magenta), C (cyan) and 
Y (yellow), 3 chart types are printed on one sheet: 
H-F (left), V (right), H-R (horizontal).
Chart Example
4Find the location on each chart where 2 lines most 
closely overlap each other. If this is the 0 position, 
registration for that color is not required. For...

Default Setting (System Menu)
8-49
8
You cannot use the numeric keys to enter these 
values.
8Repeat steps 6 and 7 to enter the registration 
values for each chart.
9Press [Execute] after all values have been entered. 
Color registration begins.
10Press [OK] after color registration is complete.
Detailed Settings
Follow the steps below to perform more detailed correction.
1Refer to Steps 1-2 of Normal Registration to display 
the Color Registration screen.
2Press [Detail].
3Press [Print] of Chart...

Default Setting (System Menu)
8-50
4Find the location on each chart where 2 lines most 
closely match. If this is the 0 position, registration 
for that color is not required. For the illustration, B 
is the appropriate value.
From charts V- 1 to V- 5, read only the values from 
V- 3 (center).
5Press [Next] of Registration (Details).
6Press [Change] for the chart to be corrected.
7Press [+] or [-] to enter the values read from the 
chart and press [OK].
Press [+] to increase the value from 0 to 9. To...