Konica Minolta magicolor 1650EN User Manual

							Configuration Menu Overview 4-12
PAGE
RECOV-
ERYSettingsON/OFF
Select whether or not the page is printed again after recovering 
from a paper misfeed.
If 
ON is selected, the page that was misfed is printed again.
If 
OFF is selected, printing continues with the next page without 
printing the misfed page.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview4-13
QUALITY MENU
With this menu, settings for the print quality can be specified.
BLACK
CYAN
MAGENTA
TONER OUT ACTION
REPLACE TONER
AIDCREQUEST AIDC
QUALITY MENU
YELLOW
P/H CLEAN UP
MODE
REMOVE ALL
IMAGE REFRESH
ECONOMY PRINT
DUPLEX SPEED
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 4-14
All factory default values are shown in bold.
REPLACE 
TONERBLACKSettingsYES/NO
If YES is selected, the carousel rotates to the black 
toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 6-5.
CYANSettingsYES/NO
If YES is selected, the carousel rotates to the cyan 
toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 6-5.
MAGENTASettingsYES/NO
If YES is selected, the carousel rotates to the 
magenta toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 6-5.
YELLOWSettingsYES/NO
If YES is selected, the carousel rotates to the yellow 
toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 6-5.
REMOVE 
ALLSettingsYES/NO
If YES is selected, the printer enters REMOVE ALL 
mode.
This mode is used when removing all toner car-
tridges.
For details on removing all toner cartridges, refer to 
“Removing All Toner Cartridges” on page 6-12.
TONER 
OUT 
ACTIONSettingsSTOP/CONTINUE
If STOP is selected, printing stops when the toner cartridge is 
empty.
If 
CONTINUE is selected, printing continues even if the toner 
cartridge is empty. However, the printing result are not 
guaranteed. If printing is continued, the message X TONER 
LIFE END appears and printing stops.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview4-15
AIDC REQUEST 
AIDCSettingsYES/NO
If YES is selected, image adjustments are 
performed.
The AIDC function consumes toner.
MODESettingsON/OFF
If ON is selected, the image adjustments are 
applied.
If 
OFF is selected, image adjustments are not 
applied.
P/H 
CLEAN  
UPSettingsYES/NO
If YES is selected, the printer enters P/H CLEAN UP mode.
P/H CLEAN UP mode is a mode that allows the user to clean the 
print head window more easily. The print head window is not 
cleaned automatically.
For details on cleaning the print head window, refer to “Cleaning 
the Print Head Window” on page 7-9.
IMAGE 
REFRESHSettingsYES/NO
Use when thin white horizontal lines appear at intervals on 
images.
The IMAGE REFRESH function consumes toner.
ECONOMY 
PRINTSettingsON/OFF
Select whether to print graphics with a reduced density by 
reducing the amount of toner that is used.
If 
ON is selected, the amount of toner used is reduced when 
printing.
If 
OFF is selected, the amount of toner used is not reduced when 
printing.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 4-16
DUPLEX 
SPEEDSettingsAUTOMATIC/SPEED/QUALITY
Select the print speed for double-sided printing.
If 
AUTOMATIC is selected, the print speed is automatically 
selected.
If 
SPEED is selected, the print speed has priority; however, the 
print quality may decrease.
If 
QUALITY is selected, the print quality has priority; therefore, 
the print speed will decrease while the print quality may increase.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview4-17
INTERFACE MENU
With this menu, interface settings can be specified.
The printer must be rebooted after any setting in the ETHERNET menu (for 
example, the TCP/IP address) is changed.
Therefore, the following message appears when the configuration menu is 
exited (the + key is repeatedly pressed) after a setting has been changed. 
Select YES, and then press the Menu Select key to reboot the printer.
Otherwise, turn off the printer, and then turn the printer on again after a few 
seconds.
ETHERNET*
INTERFACE MENU
TCP/IPENABLE
IPV4DHCP/BOOTP
IPV4 ADDRESS
DEFAULT ROUTER
SUBNET MASK
ENABLE AUTO IP
ENABLEIPV6
IDENTIFIERENABLE HTTPIP SERVICES
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 4-18
* If MAIN MENU/SYSTEM DEFAULT/SECURITY/CONFIG/
ENABLE
 is set to ON, the administrator password must be entered to 
display this menu.
For details on the default administrator password, refer to “SYSTEM 
DEFAULT” on page 4-22.
FRAME TYPEIPX/SPX
ETHERNET SPEED
DISABLE 802.1X
PS PROTOCOL
ENABLE
JOB TIMEOUT
USB
ENABLE AUTO
GLOBAL PREFIX
DISABLE FILTERS
DISABLE IPSEC
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview4-19
All factory default values are shown in bold.
ETHER-
NETTCP/IP ENABLESettingsYES/NO
If YES is selected, TCP/IP is enabled.
If 
NO is selected, TCP/IP is disabled.
IPV4 DHCP/
BOOTPSettingsYES/NO
Select whether or not the IP 
address is automatically 
acquired.
If 
YES is selected, the IP address 
is automatically acquired.
If 
NO is selected, the IP address 
is not automatically acquired.
IPV4 
ADDRESSSettings192.168.001.002
Set the IPv4 address for this 
printer on the network.
Use the +, ,, *, and ) keys to 
specify the value.
If the IP address is manually 
specified, 
DHCP/BOOTP is 
automatically set to 
NO.
DEFAULT 
ROUTERSettings000.000.000.000
Specify the IPv4 address of the 
router if one is on the network. 
Use the +, ,, *, and ) keys to 
specify the value.
SUBNET 
MASKSettings000.000.000.000
Specify the subnet mask for the 
network.
Use the +, ,, *, and ) keys to 
specify the value.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 4-20
ENABLE 
AUTO IPSettingsYES/NO
Select whether or not the IPv4 
address is automatically acquired 
when 
DHCP/BOOTP and PING, 
ARP are not functioning or when 
there is no response.
If 
YES is selected, the IP address 
is automatically acquired.
If 
NO is selected, the IP address 
is not automatically acquired.
IPV6 ENABLESettingsYES/NO
If YES is selected, IPv6 is 
enabled.
If 
NO is selected, IPv6 is disabled.
IDENTI-
FIERDisplays the Link-Local address.
ENABLE 
AUTOSettingsYES/NO
If YES is selected, auto 
configuration of IPv6 is enabled.
If 
NO is selected, auto 
configuration of IPv6 is disabled.
GLOBAL 
PREFIXDisplays the global address.
IP SER-
VICESENABLE 
HTTPSettingsYES/NO
If YES is selected, HTTP is enabled.
If 
NO is selected, HTTP is disabled.
DISABLE 
FILTERSSettingsYES/NO
If YES is selected, filter is disabled.
DISABLE 
IPSECSettingsYES/NO
If YES is selected, IPsec is disabled.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview4-21
IPX/SPX FRAME 
TYPESettingsAUTO/802.2/802.3/ETHER 
II/SNAP
Specify the protocol used with NetWare.
ETHER-
NET 
SPEEDSettingsAUTO/100 FULL DUPLEX/100 HALF 
DUPLEX/10 FULL DUPLEX/10 HALF 
DUPLEX
Specify the transmission speed for the network and the 
transmission method for bi-directional transmission.
DIS-
ABLE 
802.1XSettingsYES/NO
If YES is selected, IEEE802.1x function is disabled.
PS PRO-
TOCOLSettingsBINARY/QUOTED BINARY
Select whether PostScript jobs are received in the binary 
format or the quoted format.
USB ENABLESettingsYES/NO
If YES is selected, USB is enabled.
If 
NO is selected, USB is disabled.
JOB 
TIMEOUTSettings0-60-999
Specify the length of time (in seconds) until the print job 
being received is timed out when USB is being used.
Downloaded From ManualsPrinter.com Manuals