Konica Minolta magicolor 1650EN User Manual

							Status, Error, and Service Messages 8-34
Error Messages (Operator Call)
This 
message...means... do this...
AUTH
TIMEOUTThe user is automatically 
logged off due to IEEE802.1x 
port authorization.Reauthorize the IEEE802.1x 
port, and then log on.
AIDC 
ERRORAIDC sensor error. Open and close front cover 
to automatically clean AIDC 
parts.
BELT 
ERRORThe printer detected incorrect 
image position on the image 
transfer belt.Check the cyan and black 
toner cartridges and replace 
them if they have run out.
If the error has not been 
recovered by this proce-
dure, please call Technical 
Support.
DUPLEX 
UNIT
PANEL 
OPENDuplex cover is open. Close the duplex cover.
DOWNLOAD 
IMAGE 
INVALIDWhile updating code, an error 
has occurred.The user should attempt the 
upgrade process again.
I/C LIFE 
ENDThe imaging cartridge is 
reached the end of its life.Replace the imaging car-
tridge.
PAPER JAM
DUPLEXMedia has misfed in the 
duplex option.Locate and remove the mis-
feed.
PAPER JAM
EXITMedia has misfed in the fuser 
area.
PAPER JAM
FUSER
PAPER JAM
TRANSFER
Media has misfed in the trans-
fer roller area. This type of 
misfeed means that the media 
did not make it to the paper 
exit area.
PAPER JAM
TRAY 2Media has misfed while being 
pulled from Tray 2.Locate and remove the mis-
feed.
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages8-35
PUT
SIZE
TYPE
IN TRAY 1The size of paper being 
printed on is different from the 
size of paper specified in the 
printer driver.Load the correct paper on 
Tray1, and press the Menu 
Select key, then specify the 
size and type of the paper.
PUT 
“SIZE” 
“TYPE”
IN TRAY 2The paper size set from the 
printer driver is different from 
the size of paper loaded into 
Tray 2. „Open Tray 2 and keep 
correct paper size. Then 
close Tray 2.
„Specify the correct paper 
size in the 
MAIN MENU/
PAPER MENU/INPUT 
TRAY/TRAY2/MEDIA 
SIZE
 menu.
TOP COVER 
OPENThe printer’s top cover is 
open.Close the top cover.
The imaging cartridge is not 
installed.Install the imaging cartridge.
A imaging cartridge incompati-
ble with the machine is 
installed.Replace the imaging car-
tridge with a correct one.
X TONER 
LIFE ENDThe X toner cartridge has 
reached the end of its life.Replace the toner cartridge.
If the MAIN MENU/
QUALITY MENU/
TONER OUT 
ACTION
 menu is set 
to 
CONTINUE.
X TONER
MISSINGThe X toner cartridge is not 
installed.Install a X toner cartridge.
X TONER 
OUT
REPLACE 
XXXX
(Ready Indica-
tor: Off. Error 
Indicator: On)The X toner cartridge is empty.
(If the MAIN MENU/
QUALITY MENU/TONER OUT 
ACTION menu is set to STOP.)Replace the toner cartridge.
If the MAIN MENU/
QUALITY MENU/
TONER OUT 
ACTION
 menu is set 
to 
CONTINUE, 
printing can continue. 
However, the printing 
results are not 
guaranteed. This 
message...means... do this...
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages 8-36
Service Messages
These messages indicate a more serious error that can only be corrected by 
a customer service engineer. If one of these messages appears, turn the 
printer off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.  
This service 
message...means... do this...
SERVICE 
CALL XXXXAn error has been detected 
with the item indicated “XXXX” 
in the service message.Reboot the printer. This often 
clears the service message, 
and printer operation can 
resume.
If the problem persists, con-
tact Technical Support.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 9-2
Introduction
Note
Use of accessories not manufactured or supported by 
KONICA MINOLTA will void your warranty. 
This chapter provides information about the following accessories.
Note
Installing accessories always requires that the printer and accessories 
are turned off and unplugged during installation.
For details on the available options, refer to 
printer.konicaminolta.com. Tray 2500-sheet tray
Duplex OptionAuto duplexing
In order for the duplex option to be installed, 
Tray 2 must be installed on the printer.
Duplex Option and 
Attachment Auto duplexing
The attachment is an interface unit for 
installing the duplex option on the machine.
During installation, install the attachment 
before installing the duplex option.
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 29-3
Tray 2
If Tray 2 is installed, up to 500 additional sheets of A4/Letter-size paper can 
be loaded.
Installing Tray 2
Note
Since consumables are installed in the printer, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 2 9-4
2Remove the dust cover from Tray 1.
Close Tray 1 and the output tray.
3Prepare Tray 2.
Be sure to place Tray 2 on a level surface.
4Lift the printer and place it on top 
of Tray 2, making sure that the 
positioning pins on Tray 2 cor-
rectly fit into the holes in the bot-
tom of the printer.
5Open Tray 1 and reattach the dust cover.
6Load paper into Tray 2.
For details on loading paper, refer to “Tray 2” in “Loading Plain Paper” on 
page 5-18.
7Insert Tray 2 into the printer.
8Reconnect all interface cables.
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 29-5
9Reconnect the power cord, and 
turn on the printer.
10Declare the Tray 2 in the Windows printer driver (Properties/Configure 
tab, see page 2-2).
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option 9-6
Duplex Option
Duplex (Double Sided) printing can be performed automatically with the 
duplex option installed. 
See “Duplexing” on page 5-21.
In order for the duplex option to be installed, either of the following must be 
installed on the printer.
zTray 2
zAttachment
If Tray 2 is installed, it is not necessary to install the attachment. In this 
case, skip “Installing the Attachment”, and continue with “Installing the 
Duplex Option” on page 9-8.
Installing Attachment
If the attachment is installed, the duplex option can be installed.
(The attachment cannot be used by itself; it must be used together with the 
duplex option.)
Note
Since consumables are installed in the printer, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
Attachment
Duplex option
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option9-7
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Remove the dust cover from 
Tray 1.
Close Tray 1 and the output tray.
3Prepare the attachment.
Be sure to place the attachment on a level surface.
4Lift the printer and place it on top 
the attachment, making sure that 
the positioning pins on the 
attachment correctly fit into the 
holes on the bottom of the 
printer.
5Open Tray 1 and reattach the dust cover.
Next, install the duplex option.
Downloaded From ManualsPrinter.com Manuals