Key Voice Voice Processing System Installation And Maintenance Manual

INSTALLATION AND MAINTENANCE MANUAL 4/0023-4RJ14  4-wireLine  1&2Line  1Line  2Line  1Line  2Line  1&2RJ14  4-wire
Port 1&2
Port 3&4Port  3 Port  1
Port  2
Port  4Fax  BoardVoice BoardA
A Splitting  RJ14  LinesFigure 23-2  Connecting Telephone Lines to the Fax Boards (Splitting RJ14 Lines)
Note:Adapter A accepts either a 2-wire (1 pair) or 4-wire (2 pair) input.  In the usage above, theinput is a 4-wire (2 pair) RJ14. The outputs are as illustrated: Line 1 (the first pair), Line 2(the second pair), and...

INSTALLATION AND MAINTENANCE MANUAL 4/0023-5Note Each board must be configured individually.  Only after all boards are configured with theSatisfaxion software can you insert all boards into the PC.7. Replace the cover of the PC.
23.2.3 Installing Satisfaxion Software and Configuring Each Board
To install the Satisfaxion software and configure each board:
Note:This Satisfaxion board software installation procedure assumes you are using PureData’s5-diskette installation pack.  If the installation pack you...

INSTALLATION AND MAINTENANCE MANUAL 4/0023-612. To save the changes and edit the setup program, select OK then press .
13. To continue, press any key.
14. Restart the computer.  Continue with the following procedure for making necessary file
modifications.  If you are installing multiple boards, you can make these modifications once, after the
last board has been configured using this procedure.
To make necessary file modifications for Satisfaxion boards:
1. Shut down the VP system if it is running.
2....

INSTALLATION AND MAINTENANCE MANUAL 4/0023-7· Remove the lines in the AUTOEXEC.BAT file that call CASMGR.
· Remove the lines in the CONFIG.SYS file that invoke the SATISFAX driver.
11. If the VP system is being installed to use a phone system that does not use dial tone (such as a
Comdial switch), you must modify the I3LOAD.INI file in the sub-directory C:\INSTCOM.  Using a text
editor, access the I3LOAD.INI file.  If you are using the DOS editor for example, from the C:\INSTCOM
directory prompt, type...

INSTALLATION AND MAINTENANCE MANUAL 4/0023-8Switch SW1-123Channel AA PhysicalAddressChannel BB PhysicalAddressOnOnOff130h-133h28134h-137h29CPI4 Boards, Rotary Switch  SW1I/O Addresses (Physical Channels)Switch SettingChannel AChannel BChannel CChannel...

INSTALLATION AND MAINTENANCE MANUAL 4/0023-91. Shut down the VP system if it is running.  For complete procedures, refer to section 2.5.
2. Insert the VP system installation CD-ROM in the CD-ROM drive and close the drive.  The PC
automatically launches the installation wizard.  (If the installation program does not automatically
launch, from the Start button at the bottom of the Windows NT desktop, select Run, then in the Run
dialogic box, select the CD-ROM drive in the LOOK IN field.  Double-click on...

INSTALLATION AND MAINTENANCE MANUAL 4/0023-107. When the setup program finishes initializing, at the prompt, press  (scan all addresses).  The
setup program detects all fax channels in the PC.  If it does not detect all channels, re-configure the
fax board(s) using different I/O addresses.
8. Press  to exit the setup program.  The program indicates that it will change the fax
configuration file.
9. To continue, press .
10. Type FAXNUM then press  to run the Faxnum utility.  This utility verifies the link...

INSTALLATION AND MAINTENANCE MANUAL 4/0023-11editor, access the I3LOAD.INI file.  If you are using the DOS editor for example, from the
C:\VMFAXG\BIN directory prompt, type EDIT I3LOAD.INI then press .  After the line that
reads [GAMMAFAX], add the following line (with no blank line after it):
DIAL_PROGRESS_MODE = NONE
11. Save and exit the file.
12. Restart the computer.
23.3 Sharing Fax PortsIf a caller requests a fax be sent on the current call, the VP system determines whether there is a fax board...

INSTALLATION AND MAINTENANCE MANUAL 4/0023-129. Re-start the VP program.
23.4 Using Enhanced Fax Configurations23.4.1 Using Fax Boards with Dedicated Telephone Lines
If the VP system is handling many fax requests, you may find access to standard features (voice mail and
auto attendant) is being limited.  You may want to re-configure the system to give the fax boards their
own, dedicated telephone lines.  Although the voice boards are still involved with the fax requests, the
actual fax transmissions do...

INSTALLATION AND MAINTENANCE MANUAL 4/0023-13To telephone
system voicemail station portsLine 8 Line 7Line 6Line 5Voice mail boardFax board 1
Fax board 2 Fax board 3 Fax board 4LineLineLineLineLine 4Line 3Line 2Line 1Figure 23-3   Connecting the Fax Boards to Dedicated Telephone Lines
23.4.2 Using a Third-Party Application to Send Faxes
The VP system allows you to send faxes via a third-party fax server instead of the integrated fax
distribution configuration.  When a caller orders one or more fax...