Key Voice Voice Processing System Installation And Maintenance Manual

INSTALLATION AND MAINTENANCE MANUAL 4/0012-32Configuration FileEntryDescriptionMinimumValue toMaximumValueDefault SetupRING RESETThis parameter should only be used if the field RINGS
TO ANSWER on the LINE INFORMATION screen is
greater than 1.  When the VP system is counting rings,
it measures the time separating each ring.  If this time
exceeds a certain threshold, then the VP system
assumes that a call has been abandoned and a new
one has started ringing.  You can use this parameter
to change the value...

INSTALLATION AND MAINTENANCE MANUAL 4/0012-33Configuration FileEntryDescriptionMinimumValue toMaximumValueDefault SetupSAVE TRACENT-based VP systems only:  By default, when the
diagnostic trace utility is running, the TRACE.LOG file
is kept open, and trace entries are written to it.  The
trace file is closed only when the diagnostic trace utility
is turned off.  When the trace file runs continuously, it
may not close properly if the system locks up or
experiences power loss unexpectedly, and therefore,...

INSTALLATION AND MAINTENANCE MANUAL 4/0012-34Configuration FileEntryDescriptionMinimumValue toMaximumValueDefault SetupSERVICE OBSERVE
CODE
(Enter this as one line
of text in the VM.CFG
file.)Include this option on VP systems with Comdial
integrations to activate the record conversation feature
for a certain port on a Comdial phone system.  Enter
as:
SERVICE OBSERVE CODE = #03X
Where #03X is the code the VP system needs to dial
to initiate the Service Observing feature on the
extension who requested that...

INSTALLATION AND MAINTENANCE MANUAL 4/0012-35Configuration FileEntryDescriptionMinimumValue toMaximumValueDefault SetupTCNAMEThis parameter requires the optional Talking
Classifieds software.  Enter this parameter to request
the name of a caller to the Talking Classifieds
Gateway box.0 to 1Caller’s name is
not requested.TDD AUTOThis option tells the VP system that it needs to provide
TDD support.  It assigns the value 8 to the TDD DIGIT
(see below) and causes a TDD prompt to be played
immediately after...

INSTALLATION AND MAINTENANCE MANUAL 4/0012-36Configuration FileEntryDescriptionMinimumValue toMaximumValueDefault SetupTUTORIAL REPSBy default, the first time a user logs in to a mailbox, the
VP system plays a tutorial. The VP system plays the
tutorial every subsequent time the subscriber logs into
the mailbox, until he/she cancels the tutorial by
pressing the * key or until the maximum specified by
this parameter is reached.
This option identifies the number of times the VP
system plays the tutorial...

INSTALLATION AND MAINTENANCE MANUAL 4/0012-37Configuration FileEntryDescriptionMinimumValue toMaximumValueDefault SetupVCM ANSWER
DELAY
(Enter this as one line
of text in the VM.CFG
file.)On NT-based systems only:  This option is used in
conjunction with the VCM feature.  If the VP system
needs to use a line to play messages to a VCM user, it
calls the VCM user’s extension number and waits for it
to answer.  Once the VP system detects the VCM user
has answered, it begins playing the message.  If you
do...

INSTALLATION AND MAINTENANCE MANUAL 4/0012-38Configuration FileEntryDescriptionMinimumValue toMaximumValueDefault SetupXFER NAME TIMEIf you have configured the VP system to ask the caller
for his/her name before performing a transfer, the VP
system says, “Please speak your name so I may
announce who is calling” and allows the caller 4
seconds to record his/her name.  Use the XFER
NAME TIME statement if you want to change the
amount of time allowed to record the name.1 to 9994 seconds. 

INSTALLATION AND MAINTENANCE MANUAL 4/0013-113. Detecting Call-progress Tones
When the VP system is performing a call transfer or placing an outgoing call, it must listen to the line to
determine whether the line is busy, is ringing, or has been answered.  There are also times when the VP
system must detect tones that indicate a caller has disconnected.  On many occasions the default tone
detection files provided with the VP system sufficiently allow the system to detect these call-progress
tones,...

INSTALLATION AND MAINTENANCE MANUAL 4/0013-213.1.2 Starting Accucall
1. If the VP system has not been loaded or is not currently running, from the \VM directory, type
RHETDRV then press .  This command loads the software into the Rhetorex voice board driver.
If the driver software has previously been installed, you get the message:
RDSP DRIVER PREVIOUSLY LOADED AT INTERRUPT - xx
If the VP system is currently running, exit to DOS by pressing  from the LINE STATUS screen
(you do not need to load RHETDRV)....

INSTALLATION AND MAINTENANCE MANUAL 4/0013-3Auto Run Minimum Cycles
This field indicates the minimum number of cycles of the tone being sampled that should be detected
during the test run.  This parameter works in conjunction with the AUTO RUN VERIFICATION COUNT field
explained above.  For example, if you choose the default 10 for this parameter and you choose 2 for the
Auto Run Verification Count, the compete test sample of a tone will consist of two test runs with ten
cycles of the tone in each run....