JVC Projector Dla Rs2 Instructions Manual

							11
Getting StartedPreparation Basic Operation Settings Troubleshooting Others
ENGLISH
WARNING
LAMP
STANDBY/ON
HIDE
INPUT
STANDBY/ON
MENU
ENTEREXIT
Light on (Red):Warning mode ( pP39 )
Light on/Blinking (Orange): Lamp warning ( pP39 )
To turn on/off the power
To hide the image temporarily ( pP21 )
To return to the previous menu
To switch input
(p P20 )
To display the menu (p P24 )
Light on (Red):
Standby mode
Light on (Green): During projection
Blinking (Green): Image is temp orarily hidden
( p P21 )
Blinking (Red): Cool Down mode ( pP21 )
To select or confirm
Air Inlets/Filter ( pP43 )
To adjust the position of the image ( pP19 )
Feet: The height (0 
f 5 mm) can be adjusted by  turning the foot.
„Bottom Surface
DLA-RS2_EN.book  Page 11  Frid ay, October 12, 2007  2:43 PM 
						

							12
Controls and Features (Continued)
1Getting Started
„ Remote Control
PROJECTOR
OPERATE
LIGHT
TE ST EXIT
S
HARP
-
SHARP+
U SER2
S
-VIDEO
VIDEO A SPECT
HDMI 2
OFF........ ........
HDMI 1 COMP.
N
NATURAL
CINEMA DYNAMIC
COLOR
TEMP
GAMMA
U
SER
3
D
COLOR-
COLOR+
U SER1
C
CONTRA ST BRIGHT
HIDE
INFO
MENU
ENTER
ON
To turn on the power
To set the screen size
( p P22 )
To set gamma
( p P34 )
To adjust the outline of the image
( p P34 )
To set color temperature
( p P34 )
To hide the image temporarily
( p P21 )
To adjust brightness
(
p P34 )
To return to the previous menu
To illuminate buttons on the remote control
To select or confirm
Select input mode (
pP20 )
To turn off the power
To adjust color density (p P34 )
To switch image profile
(p P34 )
To adjust contrast (p P34 )
To display information
To display the menu (p P24 )
To display test patterns
For adjusting the image size
(zoom) and the focus. ( pP20 )
DLA-RS2_EN.book  Page 12  Frid ay, October 12, 2007  2:43 PM 
						

							13
Getting StartedPreparation Basic Operation Settings Troubleshooting Others
ENGLISH
How to Use the Remote Control
zIf the remote control has to be brought closer to the projector  to operate, it means that the batteries are wearing out. When t his 
happens, replace the batteries.  In sert the batteries according to the +- marks.
zBe sure to insert the  - end first.
zIf an error occurs when using the remote control, remove th e batteries and wait for 5 minutes. Load the batteries again and 
operate the remote control.
Loading Batteries
Effective Range of Remote Control Unit
„ When directing the remote control 
toward this unit
z
When aiming the remote control towards the 
remote sensor on this unit, ensure that the 
distance to the sensor in front or at the rear of 
this unit is within 7 m.
zIf the remote control fails to work properly, 
move closer to this unit.
„When reflecting off a screen
z
Ensure that total of distance A between this 
unit and screen and distance B between 
remote control and screen is within 7 m.
zAs the efficiency of signals reflected from the 
remote control unit diff er with the type of 
screen used, operable distance may 
decrease.
12 3
O PE R
AT
E
LIG
HT
T E S
T E
X I
T
S
H
A
R P-S
H
A
R P+US
ER2
S
-
V I
D E
O
V I
D E
O A
S P
EC T
H
D
M I2O
F
F..
... ..
. ..
.. .. ..H
D MI
1 C
O MPNN
A
T
U RA
L
C
IN E
M A
DY
N AM
ICC O
LO
R
T E M
P
G
A
M
M A
U
SE
R3DC O
LO
R-CO
LO
R+US
E R1CC ON
T
R AS
T B
R IG
H
TH ID
E
I
N F
O
M EN
UENT
ER
O N
3
0 °
2 0°
2
0° 3
0 °
3 0 °
2 0°
2
0° 3
0 °
3 0 °
20°20° 30°
30°
Remote Control
This unit
O
P
ERA
TE
LI
G H
T
T E S
T E
X I
T
S
H
AR
P
-SH
AR
P+U S
E R2
S-
V
ID
EO
V
I
D EO
ASPEC
T
H
D
M I
2
O F
F.
.. ..
....
....
...H D
M
I
1 C
O M PNNA
T U
R A
L
C IN
EM
A D
Y N
AM I
CC
O L
O R
T E
M P
G
A
M M
A
U
S
E R3DC
O L
O R-C
O L
O
R+US
ER1CC O NT
R A
S T B
R
IG
H
THID
E
I
N F
O
M EN
UENT
ER
ON
2
0°
2
0° 3
0°
3 0°
A
B20° 20° 30°
30°
A
B
This unit
Remote Control
Screen
DLA-RS2_EN.book  Page 13  Frid
ay, October 12, 2007  2:43 PM 
						

							2Preparation
14
Selecting Connecting Devices
zDo not turn on the power until connection is complete.
zThe connection procedures differ according to the device used. For details, refer to  the instruction manual of the device to be 
connected.
zFor audio output, connect the device to an amplifier.
zThe images may not be displayed depending on  the devices and cables to be connected.
Use an HDMI compliant cable (sol d separately) with the HDMI logo.
zIt may not be possible to connect to this unit depending  on the dimension of the connector cover of the cables to be 
connected.
S -VIDEO HDMI 2 HDMI 1 R
S-232C
COMPONENT
VIDEO
S YNCYCB/PBCR/PRGBR
COMPONENTOMPONENTCOMPONENT
DVD Recorder DVD Player
Notebook PC VCR and camcorder
To connect via S-video terminal (
pP15 )
To connect via video terminal (
pP15 )
To connect RS-232C terminal
To connect via component video terminals ( pP15 )
To connect via HDMI terminal (
pP16 )
DLA-RS2_EN.book  Page 14  Frid ay, October 12, 2007  2:43 PM 
						

							15
ENGLISH
Getting StartedPreparationBasic Operation Settings Troubleshooting Others
Connecting
zSet “COMP” in the setting m enu to “Y Pb/Cb Pr/Cr”. (pP28  - Q )
Connecting via Video Cable and S-video Cable
Connecting via Component Video Cable
S-VIDEO HD RS-232C
OMPONENT
VIDEO
SYNCYCB/PBCR/PRGBR
HDRS-232COMPONENT
YCB/PBCR/PRGBR
Video cable (sold separately)
VCR and camcorder
Video output
To video input terminal
This unit
S-video output
S-video cable (sold separately)
To S-video input terminal
S-VIDEO HD RS-232C
OMPONENT
VIDEO
SYNCYCB/PBCR/PRGBRS-VIDEO
HDRS-232COMPONENT
VIDEOSYNC
OMPONENT
Component video output terminals
Component video cable (sold separately) DVD player
To component video input terminals
This unit
C
R/PR(Red)
C
B/PB(Blue)
Y (Green)
DLA-RS2_EN.book  Page 15  Frid ay, October 12, 2007  2:43 PM 
						

							16
Connecting (Continued)
2Preparation
Connecting via HDMI Cable
Connecting via HDMI-DVI Conversion Cable
S-VIDEOHDMI 2 HDMI 1 RS-232C
COMPONENT
VIDEO
SYNCYCB/PBCR/PRGBRS-VIDEO
RS-232CCOMPONENT
VIDEOSYNCYCB/PBCR/PRGBR
CO
HDMI output terminal
HDMI cable (sold separately) DVD recorder
To HDMI 1 or HDMI 2  input terminal
This unit
S-VIDEO
MDMI 2 MDMI 1 RS-232C
COMPONENT
VIDEO
SYNCYCB/PBCR/PRGBRS-VIDEO
RS-232CCOMPONENT
VIDEOSYNCYCB/PBCR/PRGBR
CO
Notebook PC
To HDMI 1 or HDMI 2  input terminal
This unit
HDMI-DVI conversion cable (sold separately) DVI output terminal
DLA-RS2_EN.book  Page 16  Frid
ay, October 12, 2007  2:43 PM 
						

							17
ENGLISH
Getting StartedPreparationBasic Operation Settings Troubleshooting Others
zSet “COMP” in the setting menu to “SCART”. ( pP28  - Q )
zSet “COMP” in the setting menu to “RGB”. ( pP28  - Q )
zFor information on compatible input signals, see “Specifications”. ( pP52 )
Connecting via SCART-RCA Cable
Connecting via RGB Video Cable
S-VIDEO HD RS-232C
OMPONENT
VIDEO
SYNCYCB/PBCR/PRGBRS-VIDEO
HDRS-232COMPONENTOMPONENT
SCART-RCA cable (sold separately) DVD player for European market
To RGB video and sync signal input terminals
This unit
SCART terminal
S-VIDEOHD RS-232C
OMPONENT
VIDEO
SYNCYCB/PBCR/PRGBRS-VIDEO
HDRS-232COMPONENT
VIDEOSYNC
OMPONENT
RGB video output terminals
RGB video cable (sold separately) Device equipped with RGB output
To RGB video input terminals
This unit
R (Red)B (Blue)
G (Green) (Includes sync signal)
DLA-RS2_EN.book  Page 17  Frid ay, October 12, 2007  2:43 PM 
						

							2Preparation
18
Installing the Projector and Screen
Install this unit and the screen. Place this unit and the screen perpendicular to each other. 
Failing to do so may give rise to trapezoidal distortion of the projected image. 
AInstall the projector and screen
80%
34% 34%
80%
S-VIDEOMDMI 2 MDMI 1 RS-232CCOMPONENTVIDEO
SYNCYCB/PBCR/PRGBR
„Left/Right position
* 0 % up/down position (center)
„Up/Down position
*0 % left/right position (center) Approximately 34 % (maximu
m) of the projected image
(Turn the dial to the left for maximum) Approximately 34 % (maximum
) of the projected image
(Turn the dial to the right for maximum)
Approximately 80 % (maximum) of the projected image
(Turn the dial to  the left for maximum)
Approximately 80 % (maximum) of the projected image
(Turn the dial to the right for maximum)
„Shifting range of projected image
DLA-RS2_EN.book  Page 18  Frid ay, October 12, 2007  2:43 PM 
						

							19
ENGLISH
Getting StartedPreparationBasic Operation Settings Troubleshooting Others
BAdjust such that the projected im age is in the center of the screen
zIt may be necessary to set “Pixel Adjust” in the setting menu after adjusting the image position. ( pP27  - J )
Determine the distance from the lens to the screen to achieve your desired screen size.
This unit uses a 2.0x power zoom lens for projection.
„ Relationship Between Projection Scre en Size and Projection Distance
z
The projection distances in the table ar e provided only as a guide. Use them as a reference during installation. 
zTo adjust the installation, use a projected image of aspect ratio 16:9.
Screen Size and Projection Distance
Projection Screen 
Size
(Diagonal Length)
Aspect Ratio 16:9
Approximate Projection Distance W (Wide)  f T (Tele)
Projection Screen 
Size
(Diagonal Length)
Aspect Ratio 16:9
Approximate Projection Distance W (Wide)  f T (Tele)
60
(Approx. 1.52 m) Approx. 
1.78 m fApprox. 
3.63 m 140
(Approx. 3.56 m) Approx.
4.24 m fApprox. 
8.54 m
70
(Approx. 1.78 m) Approx. 
2.09 m fApprox. 
4.24 m 150
(Approx. 3.81 m) Approx.
4.55 m fApprox. 
9.16 m
80
(Approx. 2.03 m) Approx. 
2.40 m f
Approx. 
4.86 m 160
(Approx. 4.06 m) Approx.
4.86 m f
Approx. 
9.77 m
90
(Approx. 2.29 m) Approx. 
2.71 m fApprox. 
5.47 m 170
(Approx. 4.32 m) Approx.
5.16 m fApprox. 
10.38 m
100
(Approx. 2.54 m) Approx. 
3.01 m fApprox. 
6.08 m 180
(Approx. 4.57 m) Approx.
5.47 m fApprox. 
11.00 m
110
(Approx. 2.79 m) Approx. 
3.32 m f
Approx. 
6.70 m 190
(Approx. 4.83 m) Approx.
5.78 m f
Approx. 
11.61 m
120
(Approx.3.05 m) Approx. 
3.63 m fApprox. 
7.31 m 200
(Approx. 5.08 m) Approx.
6.08 m fApprox. 
12.23 m
130
(Approx. 3.30 m) Approx. 
3.93 m fApprox. 
7.93 m
Moves the image up or 
down
Moves the image to the 
left or right
zAdjustment can be done easily by moving the image 
upwards towards the center.
TIPS
DLA-RS2_EN.book  Page 19  Frid
ay, October 12, 2007  2:43 PM 
						

							20
3Basic Operation
Projecting Image
.......................................................................Preparation
zRemove the lens cap.
AInsert the power plug to the power outlet
BTurn on the power
CProject the image
aSelect input mode
b Play back the selected device
DAdjust the position of  the projection screen
EAdjust the image size (zoom) and the focus
aDisplay the test pattern (crosshatch)
This section describes the basic operations to project input images on the screen.
zYou can also press the [STANDBY/ON] bu tton on the unit to turn on the 
power. ( pP11 )
zYou can also select the input mode  by pressing the [INPUT] button on 
the unit. ( pP11 )
zSee “Installing the Project or and Screen” for procedures on adjusting the 
position. ( pP18 )
PROJECTOR
OPERATE
LIGHT
TEST EXIT
SHARP
-
SHARP+
USER2
S-VIDEO
VIDEO ASPECT
HDMI 2
OFF........ ........
HDMI 1 COMP.
N
NATURAL
CINEMA DYNAMIC
COLOR
TEMP
GAMMA
USER
3
D
COLOR-
COLOR+
USER1
C
CONTRAST
BRIGHT
HIDE INFO
MENU
ENTER
ON
WARNING
LAMP
STANDBY/ON
AB
Light on (Red)
Power Cord
(Supplied)
A Connect to this unit
B Connect to the power outlet
A STANDBY/ON
ON
Light on (Green)ASTANDBY/ON
COMP.HDMI 2HDMI 1
VIDEOS-VIDEO
TESTPress repeatedly
DLA-RS2_EN.book  Page 20  Frid ay, October 12, 2007  2:43 PM