Inter-Tel Imx/Gmx 256 Installation And Field Maintenance Manual

PROGRAMMINGIssue 1, November 1994INTER-TKLPRACTICRSIhWGMX 256 INSTALLATION % MAINTENANCE
the desired station in a new user group. This proce-
dure must be followed to ensure that a station is al-
ways part of a user group.l
ALL: To include all stations in the list, select the All
command button. (The None command button can-
not be used in this window.)l
OK or CANCEL: When the station lists appear asdesired, select the OK command button. To exit
from the window without saving changes, select the
Cancel...

INTER-TRLPRACTICESIMX/GMX 256 INSTALLATION & MAINTENANCEPROGRAMMINGIssue 1, November 1994
Al_lowed Area codesRes@icted Area Codes
0All
0None
E_xtended Area Codes
11.16AREA CODES: To program the area codes for
a specific user group, highlight the desired line in the
User Croups list box then select the Area Codes com-
mand button. An area code 
programmiq window will
appear as shown above.lALLOWED and 
RE!3TRICTED AREA CODES:
To allow users in the user group to access area codes,the codes must be placed...

PROGRAMMINGIssue 1, November 1994INTER-TELPRACTKESJMX/GMX 256 INSTAUATXON & MAJNTENANCE
Al_lowed Office CodesRes@icted Office Codes
11.17OFFICE CODES: To programthe office codes
for the extended area codes in a specific User Croup,highlight the desired line in the User Croups list box
then select the Office Codes command button. An office
code programmingwindowwill appear as shown above.
0EXTENDED ARJXACODES: Begin programmingby selecting the extended area code to be pro-
grammed. Locate the desired area...

INTER-TEL4PRACTIcEslMX/GMX 256 INSTALLATION & MAINTENANCE
PROGRAMMINGIssue 1, November 1994
C.
SCOS INFORMATION (SCOS)
11.19
To prepare for programming this information,
list all unrestricted stations and those that are affected by
each of the following restrictions. (Refer to Figure 5-21,page 5-213, for a program 
plammtg sheet. Refer to
FEKKRES page 4-27 for further explanation of
SCOS.)
Restrict operator access (O+): Calls thatbeginwith
0, including international calls, are not permitted. If
this...

PROGRAMMINGIssue 1, November 1994INTKR-TELPRACTICESIMX/GMX 256 INSTALLATION & MAINTENANCE
ll.22 STATION 
CLASS OF SERVICE PRO-
GRAMMING 
DAY/NIGElT LISTS, and LCR
ADVANCES: To program the list of stations that have a
specific SCOS designation, highlight the desired SCOS
in the Station 
Class of Service Programming list box and
then select the Day List or Night List command button.
A window appears as shown below. To program LCR
Advance, highlight and select the desired LCR advance
number in either the...

INTER-TELPRACTICESIMX/GMX 256 INSTALIATION & MAINTENANCEPROGRAMMINGIssue 1, November 1994D. TOLL 
SECURITY
11.24When Toll Security is selected from the Toll Re-
striction menu, or the TOLL command is entered, the
window appears as shown below. It is used for program-
ming the toll security weekly toll limit information. Re-fer to page 4-30 in
FEANRES for a detailed
explanation.11.25 This program 
,determines whether 7- and
lo-digit calls and/or operator-assisted and international
calls will be monitored...

PROGRAMMINGIssue 1. November 1994INTER-TELPRACTICE!SIMX/GMX 256 INSTALLATION & MAINTENANCE
12. 
LEAST=COST ROUTING (LCR)12.1 
Proglamming LCR requires some preparation.
Refer to page 4-32 in FEHURESfor a description of
the feature. Then, follow the 
plamting steps listed be-
low. For a program planning sheet, refer to Figure 5-23,
page 5-217.l Facility groups: Determine the types of trunk
groups available and assign them to up to 24 facility
groups. For example, place all local trunk groups in
one...

INTER-TRLPRACTICESIMXIGMX 256 lNS’E4LLATION & MAINTENANCEPROGRAMMINGIssue 1, November 1994Actions 
setup Exit
Facility Groups
Qial Rules
~
02 Echo Area Code
03 
Echo Lot Address
04
05
06
07
0812.2 The window shown above can 
be reached by
selecting Least-Cost Routing from the Applications
menu or entering the LCR command.
12.3
ROUTE GROUPS: The Route Groups list box
shows each group number (01-19) and its description.
Each route group must be programmed with area codes,
office codes, and facility groups...

PROGRAMMINGIssue 1, November 1994INTER-TELPRACTICESIMWGMX 256 INSTAUAI’LON & MAINTENANCE
mcription:
- . Excluded
ZUl202
203
204
II
(1ok
Area/Office Code Table
Iincluded
(]
&.&pration
0Hone
Time BlockB. ROUTE GROUPS
12.9 
DESCRlPTION: To give the route group a
name of up to 20 characters, select the Description text
box and type the name.
12.10CONFIGURATION: To assign area and office
codes to tables, or to assign facility groups to time
blocks, select the desired line in the Configuration list
box and...

INTER-TELPRACTICESIMX/GMX256INtXALLATION & MAINTENANCEPROGRAMMINGIssue 1, November 1994
&scription: I/‘--figuration
m-1 ~,.kY1al I.&m-Dial &lesOrdered List. . . . .,.,........................‘~.‘.:.:.:.~:.:.:.:.:.~:::~:::::::~:::::::::::.~~:::::.:.~.:.:~:::::::::::::::::.:: :.:::.:.:.:.:. ~::~~~~~~~~~~~~~~~~ 4 1:.. x .