Inter-Tel Imx/Gmx 256 Installation And Field Maintenance Manual

PRGGRAMMINGINTER-TELPRACTICE8Issue 1, November 1994IMWGMX 256 INSTALLATlON % MAINTENANCE
Inactivity Alarm
Inter-Ring Silence
Interdigit (Long)
152-255 seconds
Interdigit (Short)
42-30 seconds
LCR Advance
8
l-255 seconds
I
Loop Reversal Debounce
Message Wait
5
Off-Hook Voice
Announce Screening
Off-Line After Disconnect
Page
Pause Digit Length
Queue CallbackRecall
Relaxed Ring Detection62
DEFAULT
VALUF
60
10-255 seconds
60l-250 tenths
v/10 - 250/10)
25l-255 five-
hundredths
v/500 - 255/500)
l-255 seconds...

INTER-TELPRACTICESPROGRAMMfNG
lMX/GMX 256 INSTALLATION & MAINTENANCEIssue 1, November 1994
DEFAULTUF
Single-Line Hookflash
Maximum
Single-Line HookflashMinimum
Single-Line Wait
For Disconnect
System Forwarding Advance
System Forwarding Initiate
Tl Busy-Out Switch Time Out
Transfer
- Available
Transfer - Busy
Trunk Key 
Debounce
Trunk Preselect15
15
60
20
24
3
52-20 tenths
WlO i 2VlO)l-10 tenths
(l/10 - ‘O/10)
l-60 seconds
2-255 seconds
2-255 seconds
10-10000 seconds
10-255 seconds
lo-255 seconds
l-777...

PROGRAMMINGIssue 1, November 1994INrRR-TRLPRACTICESIMX/GMX 256 INSTALLATION & MAINTENANCE
DEFAULTVA1 IIF
Trunk Ring Detection5
Unsupervised-CO5Valid-Call
15Voice Mail Dialing
Delay
5l-250 tenths
v/10 ~250/10)l-255 minutes
O-60 secondsl-250 tenths
(/lo- *wlo)
This is a low-level timer that specifies the duration
that continuous ring voltage must be detected on a
CO trunk for the system to recognize a new incoming
call. If this timer is too low, then false rings could be
detected. If the timer is too high,...

INTER-TKLPRACTICESIMX/GMX 256 INS‘MLLATION % MAINTENANCEPROGRAMMING
Issue 1, November 1994
Actions &tup Exit
Tenant GroupsK. TENANTSANDDEPAR-(TNT)
10.89There can be up to eight tenant groups, with 10
departments per tenant group. In the default state, all
stations are placed in tenant group 1 and department 1.
10.90To prepare to use this program, make a list of the
stations to be assigned to each of the tenant groups. 
(All
stations must be assigned to a tenant group and a depart-
ment.) If desired, give...

PROGRAMMINGINTER-TJ3LPRACTxcEsIssue 1, November 1994IMX/GMX 256 INSTALLATlON & MAINTENANCE
&scription:
xrunk Groups
DID Groups
Dgnrtment
‘hmk Group for &JTO Feature
01 All Lines
02
03
10.94DESCRIPTION: To give the tenant group an
identifying name, select the Description text box and
type a name of up to 
20 characters.10.95 
DEPARTMENT: To program the individual
departments, move to the Department list box. When
the desired department is selected, the following win-
dow appears.10.96 TRUNK GROUP FOR AUTO...

lNTER-TELPRAcTIc~IMX/GMX 256 INSTALLATION & MAlNTENANCEPROGRAMMINGIssue 1, November 1994
sure that a station is always part of a tenant group and
department.
ALL: To include all stations in the list, select the All
command button. 
(lhe None command button can-
not be used in this window.)
OK or CANCEL: When the station lists appear asdesired, select the OK command button. To exit
from the window without saving changes, select the
Cancel command button.
SORT: To sort the stations and list them...

PROGRAMMING
Issue 1, November 1994INTER-TELPRACTIcRsIMX/GMX 256 INSTALLATION & MAINTENANCEll. TOLLRESTRICTION
11.1 When Toll Restriction is selected from the
Applications Menu window, the menu expands toohow
the following options:
Toll Restriction...
Alternate Carriers 
and Allowed Long Distance
Area/O&e Codes Allowed/Restricted
SCOS Information
1 Toll Security
11.2Each of the options and the windows they access
are described in detail in the following pages.
A AWERNATECARRIERSANDALLOWED
LONG DISTANCE...

INTER-TELPR#xTIcESIMX/GMX 256 INSTALLATION & MAINTENANCEPROGRAMMINGIssue 1, November 1994
I-Actions 
Setup Exit
Al temate Qrrier
03
04
05
0607
08
09
10Allowed 
Igng Distance
04
05
0607
08
0911.6 ALTERNATE CARRIER
and ALLOWED
LONG DISTANCE: 
To enter an alternate carrier num-
ber or allowed long distance number in the appropriate
list, highlight the desired Position on the list and select
it. The following window appears.Number:
[-Y-jl
NUMBER: Select the text box and type the number.
0OK: When finished,...

PROGRAMMING
Issue 1, November 1994INTER-TELPRACTICESIMXGMX 256 INSTALLATION & MAINTENANCEB. 
AREA/OFFICE CODES
11.8The window shown on the next page is used for
programming the 
numbefing plan flags for the system
and for programming 
area/of&e code user groups.Numbering Plan Flags
ll9The growth of telecommunications services has
created an increasing demand for more telephone num-
bers. To meet the demand, 
Bellcore has prepared a long-range North American Numbering Plan 
(NANP) to
provide additional...

INTER-TELPRACTICESlMX/GMX 256 INSTALLATION & MAINTENANCEPROGRAMMINGIssue 1, November 1994
IActions 
setup Exit
User Groups
Day Station List
06Night Station List
Office 
Cbdes Used As Area codes
0kmea Codes Used As Office Codes
n Toll Digit Allowed On Toll Local Calls
0 Toll Digit Required On Toll Long Distance Calls
11.12 The window shown above is used for pro-
gramming the various aspects of area and office code re-striction used for SCOS 5 (Area/Office Code
Restriction). To reach it, select Area/Office...