Home > HP > All in One Printer > HP Officejet 6500A e All in One E710 User Manual

HP Officejet 6500A e All in One E710 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual HP Officejet 6500A e All in One E710 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Acoustic emission specification
    Print in Draft mode, noise levels per ISO 7779
    Sound pressure (bystander position)
    LpAm 55 (dBA)
    Sound power
    LwAd 6.8 (BA)
    Memory card specifications
    • Maximum recommended number of files on a memory card: 1,000
    • Maximum recommended individual file size: 12 megapixel maximum, 8 MB maximum
    • Maximum recommended memory card size: 8 GB (solid state only)
    NOTE:Approaching any of the recommended maximums on a memory card might cause
    the performance of the printer to be slower than expected.
    Supported memory card types
    • Secure Digital
    • High Capacity Secure Digital
    • Memory Stick
    • MultiMediaCard (MMC)
    • xD-Picture Card
    Printer specifications 177
     
    						
    							Regulatory information
    The printer meets product requirements from regulatory agencies in your country/region.
    This section contains the following topics:
    •
    FCC statement
    •
    Notice to users in Korea
    •
    VCCI (Class B) compliance statement for users in Japan
    •
    Notice to users in Japan about the power cord
    •
    Noise emission statement for Germany
    •
    LED indicator statement
    •
    Gloss of housing of peripheral devices for Germany
    •
    Notice to users of the U.S. telephone network: FCC requirements
    •
    Notice to users of the Canadian telephone network
    •
    Notice to users in the European Economic Area
    •
    Notice to users of the German telephone network
    •
    Australia wired fax statement
    •
    Regulatory information for wireless products
    •
    Regulatory model number
    •
    Declaration of conformity Appendix A
    178 Technical information
     
    						
    							FCC statement
    FCC statement
    The United States Federal Communications Commission (in 47 CFR 15.105) has specified 
    that the following notice be brought to the attention of users of this product. 
    This equipment has been tested and found to comply with the limits for a Class B digital 
    device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reason-
    able protection against harmful interference in a residential installation.  This equipment 
    generates, uses and can radiate radio frequency energy and, if not installed and used in 
    accordance with the instructions, may cause harmful interference to radio communications.  
    However, there is no guarantee that interference will not occur in a particular installation.  
    If this equipment does cause harmful interference to radio or television reception, which can 
    be determined by turning the equipment off and on, the user is encouraged to try to correct 
    the interference by one or more of the following measures:
    Reorient the receiving antenna.
      Increase the separation between the equipment and the receiver.
      Connect the equipment into an outlet on a circuit different from that to which the 
    receiver is connected.
      Consult the dealer or an experienced radio/TV technician for help.
    For further information, contact:
    Manager of Corporate Product Regulations
    Hewlett-Packard Company
    3000 Hanover Street
    Palo Alto, Ca 94304
    (650) 857-1501
    Modifications (part 15.21)
    The FCC requires the user to be notified that any changes or modifications made to this 
    device that are not expressly approved by HP may void the users authority to operate the 
    equipment.
    This device complies with Part 15 of the FCC Rules.  Operation is subject to the following 
    two conditions:  (1) this device may not cause harmful interference, and (2) this device must 
    accept any interference received, including interference that may cause undesired 
    operation.
    Notice to users in Korea
    VCCI (Class B) compliance statement for users in Japan
    BB1-]ÎB2AîBjB¤BtB±ŽÛ--]ÎB*BAïBB1-]ÎB2Aî…8!cºB*
    ö!ªBBNBB+BUá›B+BB)
    
    /àBBBB+BBBMBABAïÒ.‘ÿ B.åB&B)\BBBMÒBBUBB)
    BBAï
    VCCI-B
    Regulatory information 179
     
    						
    							Notice to users in Japan about the power cord
    Noise emission statement for Germany
    Geräuschemission
    LpA < 70 dB am Arbeitsplatz im Normalbetrieb nach DIN 45635 T. 19
    LED indicator statement
    Gloss of housing of peripheral devices for Germany
    Appendix A
    180 Technical information
     
    						
    							Notice to users of the U.S. telephone network: FCC requirements
    Notice to users of the U.S. telephone network: FCC requirements
    This equipment complies with FCC rules, Part 68. On this equipment is a label that 
    contains, among other information, the FCC Registration Number and Ringer Equivalent 
    Number (REN) for this equipment. If requested, provide this information to your telephone 
    company.
    An FCC compliant telephone cord and modular plug is provided with this equipment. This 
    equipment is designed to be connected to the telephone network or premises wiring using 
    a compatible modular jack which is Part 68 compliant. This equipment connects to the 
    telephone network through the following standard network interface jack: USOC 
    RJ-11C.
    The REN is useful to determine the quantity of devices you may connect to your telephone 
    line and still have all of those devices ring when your number is called. Too many devices 
    on one line might result in failure to ring in response to an incoming call. In most, but not 
    all, areas the sum of the RENs of all devices should not exceed five (5). To be certain of the 
    number of devices you may connect to your line, as determined by the REN, you should call 
    your local telephone company to determine the maximum REN for your calling area.
    If this equipment causes harm to the telephone network, your telephone company might 
    discontinue your service temporarily. If possible, they will notify you in advance. If advance 
    notice is not practical, you will be notified as soon as possible. You will also be advised of 
    your right to file a complaint with the FCC. Your telephone company might make changes 
    in its facilities, equipment, operations, or procedures that could affect the proper operation 
    of your equipment. If they do, you will be given advance notice so you will have the 
    opportunity to maintain uninterrupted service. If you experience trouble with this equipment, 
    please contact the manufacturer, or look elsewhere in this manual, for warranty or repair 
    information. Your telephone company might ask you to disconnect this equipment from the 
    network until the problem has been corrected or until you are sure that the equipment is not 
    malfunctioning.
    This equipment may not be used on coin service provided by the telephone company.
    Connection to party lines is subject to state tariffs. Contact your state public utility commis-
    sion, public service commission, or corporation commission for more information.
    This equipment includes automatic dialing capability. When programming and/or making 
    test calls to emergency numbers:
    Remain on the line and explain to the dispatcher the reason for the call.
    Perform such activities in the off-peak hours, such as early morning or late evening.
     Note   The FCC hearing aid compatibility rules for telephones are not applicable 
    to this equipment.
    The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a 
    computer or other electronic device, including fax machines, to send any message unless 
    such message clearly contains in a margin at the top or bottom of each transmitted page 
    or on the first page of transmission, the date and time it is sent and an identification of the 
    business, other entity, or other individual sending the message and the telephone number 
    of the sending machine or such business, other entity, or individual. (The telephone number 
    provided might not be a 900 number or any other number for which charges exceed local 
    or long-distance transmission charges.) In order to program this information into your fax 
    machine, you should complete the steps described in the software.
    Regulatory information 181
     
    						
    							Notice to users of the Canadian telephone network
    Note à l’attention des utilisateurs du réseau téléphonique 
    canadien/Notice to users of the Canadian telephone network
    Cet appareil est conforme aux spécifications techniques des équipements terminaux 
    d’Industrie Canada. Le numéro d’enregistrement atteste de la conformité de l’appareil. 
    L’abréviation IC qui précède le numéro d’enregistrement indique que l’enregistrement a été 
    effectué dans le cadre d’une Déclaration de conformité stipulant que les spécifications 
    techniques d’Industrie Canada ont été respectées. Néanmoins, cette abréviation ne signifie 
    en aucun cas que l’appareil a été validé par Industrie Canada.
    Pour leur propre sécurité, les utilisateurs doivent s’assurer que les prises électriques reliées 
    à la terre de la source d’alimentation, des lignes téléphoniques et du circuit métallique 
    d’alimentation en eau sont, le cas échéant, branchées les unes aux autres. Cette précaution 
    est particulièrement importante dans les zones rurales.
    Remarque    Le numéro REN (Ringer Equivalence Number) attribué à chaque 
    appareil terminal fournit une indication sur le nombre maximal de terminaux qui 
    peuvent être connectés à une interface téléphonique. La terminaison d’une 
    interface peut se composer de n’importe quelle combinaison d’appareils, à 
    condition que le total des numéros REN ne dépasse pas 5.
    Basé sur les résultats de tests FCC Partie 68, le numéro REN de ce produit est 0.0B.
    This equipment meets the applicable Industry Canada Terminal Equipment Technical 
    Specifications. This is confirmed by the registration number. The abbreviation IC before the 
    registration number signifies that registration was performed based on a Declaration of 
    Conformity indicating that Industry Canada technical specifications were met. It does not 
    imply that Industry Canada approved the equipment.
    Users should ensure for their own protection that the electrical ground connections of the 
    power utility, telephone lines and internal metallic water pipe system, if present, are 
    connected together. This precaution might be particularly important in rural areas.
    Note   The REN (Ringer Equivalence Number) assigned to each terminal device 
    provides an indication of the maximum number of terminals allowed to be 
    connected to a telephone interface. The termination on an interface might consist 
    of any combination of devices subject only to the requirement that the sum of the 
    Ringer Equivalence Numbers of all the devices does not exceed 5. 
    The REN for this product is 0.0B, based on FCC Part 68 test results.
    Appendix A
    182 Technical information
     
    						
    							Notice to users in the European Economic Area
    Notice to users in the European Economic Area
    This product is designed to be connected to the analog Switched Telecommunication 
    Networks (PSTN) of the European Economic Area (EEA) countries/regions.
    Network compatibility depends on customer selected settings, which must be reset to use 
    the equipment on a telephone network in a country/region other than where the product 
    was purchased. Contact the vendor or Hewlett-Packard Company if additional product 
    support is necessary.
    This equipment has been certified by the manufacturer in accordance with Directive 
    1999/5/EC (annex II) for Pan-European single-terminal connection to the public switched 
    telephone network (PSTN). However, due to differences between the individual PSTNs 
    provided in different countries, the approval does not, of itself, give an unconditional 
    assurance of successful operation on every PSTN network termination point.
    In the event of problems, you should contact your equipment supplier in the first instance.
    This equipment is designed for DTMF tone dialing and loop disconnect dialing. In the 
    unlikely event of problems with loop disconnect dialing, it is recommended to use this 
    equipment only with the DTMF tone dial setting.
    Notice to users of the German telephone network
    Hinweis für Benutzer des deutschen Telefonnetzwerks
    Dieses HP-Fax ist nur für den Anschluss eines analogen Public Switched Telephone Network 
    (PSTN) gedacht. Schließen Sie den TAE N-Telefonstecker, der im Lieferumfang des 
    HP All-in-One enthalten ist, an die Wandsteckdose (TAE 6) Code N an. Dieses HP-Fax kann 
    als einzelnes Gerät und/oder in Verbindung (mit seriellem Anschluss) mit anderen zugelass-
    enen Endgeräten verwendet werden.
    Australia wired fax statement
    In Australia, the HP device must be connected to Telecommunication Network through a line 
    cord which meets the requirements of the Technical Standard AS/ACIF S008.
    Regulatory information for wireless products
    This section contains the following regulatory information pertaining to wireless products:
    •
    Exposure to radio frequency radiation
    •
    Notice to users in Brazil
    •
    Notice to users in Canada
    •
    Notice to users in Taiwan
    •
    European Union regulatory notice
    Regulatory information 183
     
    						
    							Exposure to radio frequency radiation
    Exposure to radio frequency radiation
    Caution  The radiated output power of this device is far below the FCC radio 
    frequency exposure limits. Nevertheless, the device shall be used in such a manner 
    that the potential for human contact during normal operation is minimized. This 
    product and any attached external antenna, if supported, shall be placed in such a 
    manner to minimize the potential for human contact during normal operation. In 
    order to avoid the possibility of exceeding the FCC radio frequency exposure limits, 
    human proximity to the antenna shall not be less than 20 cm (8 inches) during normal 
    operation.
    Notice to users in Brazil
    Aviso aos usuários no Brasil
    Este equipamento opera em caráter secundário, isto é, não tem direito à proteção contra 
    interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência 
    a sistemas operando em caráter primário. (Res.ANATEL 282/2001).
    Notice to users in Canada
    Notice to users in Canada/Note à l'attention des utilisateurs canadiens
    For Indoor Use. This digital apparatus does not exceed the Class B limits for radio noise 
    emissions from the digital apparatus set out in the Radio Interference Regulations of the 
    Canadian Department of Communications. The internal wireless radio complies with RSS 
    210 and RSS GEN of Industry Canada.
    Utiliser à l'intérieur. Le présent appareil numérique német pas de bruit radioélectrique 
    dépassant les limites applicables aux appareils numériques de la classe B prescrites dans 
    le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications 
    du Canada. Le composant RF interne est conforme a la norme RSS-210 and RSS GEN 
    dIndustrie Canada.
    Notice to users in Taiwan
    Appendix A
    184 Technical information
     
    						
    							European Union regulatory notice
    European Union Regulatory Notice
    Products bearing the CE marking comply with the following EU Directives:  
    · Low Voltage Directive 2006/95/EC  
    · EMC Directive 2004/108/EC
    CE compliance of this product is valid only if powered with the correct CE-marked AC adapter 
    provided by HP. 
    If this product has telecommunications functionality, it also complies with the essential 
    requirements of the following EU Directive:
    · R&TTE Directive 1999/5/EC
    Compliance with these directives implies conformity to harmonized European standards 
    (European Norms) that are listed in the EU Declaration of Conformity issued by HP for this 
    product or product family. This compliance is indicated by the following conformity marking 
    placed on the product.
    The wireless telecommunications functionality of this product may be used in the following 
    EU and EFTA countries:
    Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, 
    Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, 
    Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, 
    Slovenia, Spain, Sweden, Switzerland and United Kingdom.
    Products with 2.4-GHz wireless LAN devices
    France
    For 2.4 GHz Wireless LAN operation of this product certain restrictions apply: This product 
    may be used indoor for the entire 2400-2483.5 MHz frequency band (channels 1-13). For 
    outdoor use, only 2400-2454 MHz frequency band (channels 1-9) may be used. For the latest 
    requirements, see http://www.art-telecom.fr.
    Italy
    License required for use. Verify with your dealer or directly with the General Direction for 
    Frequency Planning and Management (Direzione Generale Pianificazione e Gestione 
    Frequenze).
    Regulatory model number
    For regulatory identification purposes, your product is assigned a Regulatory Model Number. The
    Regulatory Model Number for your product is SNPRC-1004-01 or SNPRC-1004-02. This
    regulatory number should not be confused with the marketing name (HP Officejet 6500A (E710)
    e-All-in-One series) or product number.
    Regulatory information 185
     
    						
    							Declaration of conformity
    DECLARATION OF CONFORMITYaccording to ISO/IEC 17050-1 and EN 17050-1
    Supplier’s Name:Hewlett-Packard Company DoC#: SNPRC-1004-01-ASupplier’s Address:138, Depot Road, #02-01,#04-01
    Singapore 109683
    declares, that the productProduct Name and Model:HP Officejet 6500A Plus e-All-in-One 
    Regulatory Model Number:1)SNPRC-1004-01
    Product Options:All
    Power adaptor:0957-2271Radio Module Number:SDGOB-0892
    conforms to the following Product Specifications and Regulations:
    SAFETY:IEC 60950-1, Ed 2 (2005) / EN 60950-1, Ed 2 (2006)
    EN 62311:2008
    EMC:CISPR 22:2005 +A1:2005 / EN55022:2006 +A1:2007 Class B 
    EN 55024:1998 +A1:2001 + A2:2003
    EN 61000-3-2:2006
    EN 61000-3-3:1995 +A1: 2001 + A2:2005
    FCC CFR 47, Part 15 Class B / ICES-003, Issue 4 Class B 
    Telecom:
    Energy Use:EN 301 489-1 V1.8.1:2008 / EN 301 489-17 V1.3.2:2008
    EN 300 328 V1.7.1 : 2006 
    TBR 21: 19983)FCC Rules and Regulations 47CFR Part 68
    TIA-968-A-1+A-2+A-3+A-4+A-5 Telecommunications – Telephone Terminal Equipment
    CS-03, Part I, Issue 9, Feb 2005
    Regulation (EC) No. 1275/2008
    ENERGY STAR® Qualified Imaging Equipment Operational Mode (OM) Test Procedure
    Regulation (EC) No. 278/2009 
    Test Method for Calculating the Energy Efficiency of Single-Voltage External AC-DC and AC-AC Power
    supplies
    Supplementary Information:
    1. This  product  is  assigned  a  Regulatory  Model  Number which  stays  with  the  regulatory aspects  of  the  design.  The  Regulatory  Model Number  is  the 
    main  product  identifier  in  the  regulatory  documentation  and  test  reports,  this  number  should  not be  confused  with  the  marketing name  or  the
    product numbers.
    2. This product complies with the requirements of the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, EuP Dire ctive 2005/32/EC,
    the  R&TTE  Directive  99/5/EC  and  the  European  Council  Recommendation  1999/519/EC  on  the  limitation  of  Electromagnetic  fields  to the  general
    public and carries the 
     marking accordingly. In addition, it complies with the WEEE Directive 2002/96/EC and RoHS Directive 2002/95/EC.
    3. This product complies with TBR21:1998, except clause 4.7.1 (DC characteristic), which complies with ES 203 021-3, clause 4.7.1.
    4. This  Device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the  following  two  Conditions:  (1)  This  device  may  not cause  harmful
    interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
    5. The product was tested in a typical configuration. 
    Singapore
    February 2010
    Yik Hou Meng
    Product Regulations Manager
    Customer Assurance, Business Printing Division
    Local contact for regulatory topics only:
    EMEA: Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germanywww.hp.com/go/certificates
    USA : Hewlett-Packard, 3000 Hanover St., Palo Alto 94304, U.S.A. 650-857-1501
    Appendix A
    186 Technical information
     
    						
    All HP manuals Comments (0)