Home > HP > All in One Printer > HP Officejet 6500A e All in One E710 User Manual

HP Officejet 6500A e All in One E710 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual HP Officejet 6500A e All in One E710 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							•Incompletely filled text or graphics
    Try adjusting the contrast and copy-quality settings.
    •Large, black typefaces look splotchy (not smooth)
    The default enhancement setting might not be suitable for the job. Check the
    setting and change it to enhance text or photographs, if needed. For more
    information, see 
    Change copy settings.
    •Horizontal grainy or white bands in light-gray to medium-gray areas
    The default enhancement setting might not be suitable for the job. Check the
    setting and change it to enhance text or photographs, if needed. For more
    information, see 
    Change copy settings.
    The printer prints half a page, then ejects the paper
    Check the ink cartridges
    Make sure the correct ink cartridges are installed and the ink cartridges are not low on
    ink. For more information, see 
    Printer management tools and Check the estimated ink
    levels.
    HP cannot guarantee the quality of non-HP ink cartridges.
    Paper mismatch
    Check the settings
    Verify that the loaded media size and type matches the control panel settings.
    Solve scan problems
    If the following topics do not help, see HP support for information about HP support.
    NOTE:If you are starting the scan from a computer, see the software Help for
    troubleshooting information.
    •Scanner did nothing
    •
    Scan takes too long
    •
    Part of the document did not scan or text is missing
    •
    Text cannot be edited
    •
    Error messages appear
    •
    Scanned image quality is poor
    •
    Scan defects are apparent
    Solve scan problems 127
     
    						
    							Scanner did nothing
    •Check the original
    Make sure that the original is placed on the scanner glass correctly. For more
    information, see 
    Load an original on the scanner glass.
    •Check the printer
    The printer might be coming out of PowerSave mode after a period of inactivity,
    which delays processing a short while. Wait until the printer displays the Home
    screen.
    •Check the HP software
    Make sure the HP software provided with the printer is correctly installed.
    Scan takes too long
    •Check the settings
    ◦If you set the resolution too high, the scan job takes longer and results in larger
    files. To obtain good results when scanning or copying, do not use a resolution
    that is higher than needed. You can lower the resolution to scan more quickly.
    ◦If you acquire an image through TWAIN, you can change the settings so that
    the original scans in black and white. See the onscreen Help for the TWAIN
    program for information.
    •Check the status of the printer
    If you sent a print or copy job before you tried to scan, the scan starts if the scanner
    is not busy. However, the printing and scanning processes share memory, which
    means that the scan might be slower.
    Chapter 8
    128 Solve a problem
     
    						
    							Part of the document did not scan or text is missing
    •Check the original
    ◦Make sure that you loaded the original correctly. For more information, see
    Load an original on the scanner glass.
    ◦If you are copying a borderless original, load the original on the scanner glass,
    not the ADF. For more information, see 
    Load an original on the scanner glass.
    ◦Colored backgrounds can cause images in the foreground to blend into the
    background. Try adjusting the settings before you scan the original, or try
    enhancing the image after you scan the original.
    •Check the settings
    ◦Make sure that the input media size is large enough for the original that you are
    scanning.
    ◦If you are using the HP software provided with the printer, the default settings in
    the HP software might be set to automatically perform a specific task other than
    the one that you are attempting. See the onscreen Help for the HP software for
    instructions about changing the properties.
    ◦If you have selected a picture scanning option, the HP software automatically
    crops the image. However, if you want to scan the entire page, complete the
    following steps:
    Windows: From the HP software, click Scanner Actions, click Scan
    Properties, and then select Scan the entire glass.
    Mac OS X: From the HP software, click Scan, select the Pictures scan profile,
    click Profile Settings, and then clear the Crop check box.
    Text cannot be edited
    •Check the settings
    ◦When you scan the original, make sure that you select a document type that
    creates editable text. If text is classified as a graphic, it is not converted to text.
    ◦If you are using a separate OCR (optical character recognition) program, the
    OCR program might be linked to a word-processing program that does not
    perform OCR tasks. For more information, see the documentation provided with
    the OCR program.
    ◦Make sure you have selected an OCR language that corresponds to the
    language used for the document you are scanning. For more information, see
    the documentation provided with the OCR program.
    •Check the originals
    ◦When scanning documents as editable text from the ADF, the original must be
    loaded into the ADF with the top forward and face up. When scanning from the
    scanner glass, the original must be loaded with the top facing the right edge of
    the scanner glass. Also, make sure the document is not skewed. For more
    information, see 
    Load an original on the scanner glass or Load an original in
    the automatic document feeder (ADF).
    ◦The software might not recognize text that is tightly spaced. For example, if the
    text that the software converts has missing or combined characters, rn might
    appear as m.
    Solve scan problems 129
     
    						
    							◦The accuracy of the software depends on the image quality, text size, and
    structure of the original and the quality of the scan itself. Make sure that your
    original has good image quality.
    ◦Colored backgrounds can cause images in the foreground to blend too much.
    Error messages appear
    Unable to activate TWAIN source or An error occurred while acquiring the
    image
    ◦If you are acquiring an image from another device, such as a digital camera or
    another scanner, make sure that the other device is TWAIN-compliant. Devices
    that are not TWAIN-compliant do not work with the HP software.
    ◦Make sure that you have connected the USB cable to the correct port on the back
    of your computer.
    ◦Verify that the correct TWAIN source is selected. In the software, check the TWAIN
    source by selecting Select Scanner on the File menu.
    Scanned image quality is poor 
    The original is a second-generation photo or picture
    Reprinted photographs, such as those in newspapers or magazines, are printed by
    using tiny dots of ink that make an interpretation of the original photograph, which
    degrades the quality. Often, the ink dots form unwanted patterns that can be detected
    when the image is scanned or printed or when the image appears on a screen. If the
    following suggestions do not solve the problem, you might need to use a better-quality
    version of the original.
    ◦To eliminate the patterns, try reducing the size of the image after scanning.
    ◦Print the scanned image to see if the quality is better.
    ◦Make sure that the resolution and color settings are correct for the type of scan job.
    Text or images on the back of a two-sided original appear in the scan
    Two-sided originals can bleed text or images from the back side to the scan if the
    originals are printed on media that is too thin or too transparent.
    The scanned image is skewed (crooked)
    The original might have been placed incorrectly. Be sure to use the media guides when
    you place the original on the scanner glass. For more information, see 
    Load an original
    on the scanner glass.
    The image quality is better when printed
    The image that appears on the screen is not always an accurate representation of the
    quality of the scan.
    ◦Try adjusting your computer monitor settings to use more colors (or levels of gray).
    On Windows computers, you typically make this adjustment by opening Display on
    the Windows control panel.
    ◦Try adjusting the resolution and color settings.
    The scanned image shows blots, lines, vertical white stripes, or other defects
    ◦If the scanner glass is dirty, the image produced does not have optimum clarity.
    See 
    Maintain the printer for cleaning instructions.
    ◦The defects might be on the original and not a result of the scanning process.
    Chapter 8
    130 Solve a problem
     
    						
    							Graphics look different from the original
    The graphics settings might not be suitable for the type of scan job that you are
    performing. Try changing the graphics settings.
    Take steps to improve the scan quality
    ◦Use high-quality originals.
    ◦Place the media correctly. If the media is placed incorrectly on the scanner glass, it
    might skew, which causes unclear images. For more information, see 
    Load an
    original on the scanner glass.
    ◦Adjust the software settings according to how you plan to use the scanned page.
    ◦Use or make a carrier sheet to protect your originals.
    ◦Clean the scanner glass. See 
    Clean the scanner glass for more information.
    Scan defects are apparent
    •Blank pages
    Make sure that the original document is placed correctly. Place the original
    document face down on the flatbed scanner with the top-left corner of the
    document located in the lower-right corner of the scanner glass.
    •Too light or dark
    ◦Try adjusting the settings. Be sure to use the correct resolution and color
    settings.
    ◦The original image might be very light or dark or might be printed on colored
    paper.
    •Unwanted lines
    Ink, glue, correction fluid, or an unwanted substance might be on the scanner
    glass. Try cleaning the scanner glass. See 
    Maintain the printer for more
    information.
    •Black dots or streaks
    ◦Ink, glue, correction fluid, or an unwanted substance might be on the scanner
    glass, the scanner glass might be dirty or scratched, or the lid backing might be
    dirty. Try cleaning the scanner glass and lid backing. See 
    Maintain the printer
    for more information. If cleaning does not correct the problem, the scanner
    glass or lid backing might need to be replaced.
    ◦The defects might be on the original and not a result of the scanning process.
    •Unclear text
    Try adjusting the settings. Make sure that the resolution and color settings are
    correct.
    •Size is reduced
    The HP software settings might be set to reduce the scanned image. See the HP
    software Help for more information about changing the settings.
    Solve fax problems
    This section contains fax setup troubleshooting information for the printer. If the printer
    is not set up correctly for faxing, you might experience problems when sending faxes,
    receiving faxes, or both.
    Solve fax problems 131
     
    						
    							If you are having faxing problems, you can print a fax test report to check the status of
    the printer. The test will fail if the printer is not set up correctly for faxing. Perform this
    test after you have completed setting up the printer for faxing. For more information,
    see 
    Test fax setup.
    If the test fails, review the report for information on how to fix any problems found. For
    more information, see 
    The fax test failed.
    •
    The fax test failed
    •
    The display always shows Phone Off Hook
    •
    The printer is having problems sending and receiving faxes
    •
    The printer is having problems sending a manual fax
    •
    The printer cannot receive faxes, but can send faxes
    •
    The printer cannot send faxes, but can receive faxes
    •
    Fax tones are recorded on my answering machine
    •
    The phone cord that came with my printer is not long enough
    •
    Color faxes do not print
    •
    The computer cannot receive faxes (Fax to PC and Fax to Mac)
    The fax test failed
    If you ran a fax test and the test failed, review the report for basic information about the
    error. For more detailed information, check the report to see which part of the test
    failed, and then review the appropriate topic in this section for solutions to try.
    This section contains the following topics:
    •
    The Fax Hardware Test failed
    •
    The Fax Connected to Active Telephone Wall Jack test failed
    •
    The Phone Cord Connected to Correct Port on Fax test failed
    •
    The Using Correct Type of Phone Cord with Fax test failed
    •
    The Dial Tone Detection test failed
    •
    The Fax Line Condition test failed
    The Fax Hardware Test failed
    Solution:
    • Turn off the printer by using the Power button located on the printer control
    panel and then unplug the power cord from the back of the printer. After a few
    seconds, plug the power cord in again, and then turn the power on. Run the
    test again. If the test fails again, continue reviewing the troubleshooting
    information in this section.
    • Try to send or receive a test fax. If you can send or receive a fax successfully,
    there might not be a problem.
    • If you are running the test from the Fax Setup Wizard (Windows) or HP Setup
    Assistant (Mac OS X), make sure the printer is not busy completing another
    task, such as receiving a fax or making a copy. Check the display for a
    message indicating that the printer is busy. If it is busy, wait until it is finished
    and in the idle state before running the test.
    Chapter 8
    132 Solve a problem
     
    						
    							• Make sure you use the phone cord that came with the printer. If you do not use
    the supplied phone cord to connect from the telephone wall jack to the printer,
    you might not be able to send or receive faxes. After you plug in the phone cord
    that came with the printer, run the fax test again.
    • If you are using a phone splitter, this can cause faxing problems. (A splitter is a
    two-cord connector that plugs into a telephone wall jack.) Try removing the
    splitter and connecting the printer directly to the telephone wall jack.
    After you resolve any problems found, run the fax test again to make sure it passes
    and the printer is ready for faxing. If the Fax Hardware Test continues to fail and
    you experience problems faxing, contact HP support. Go to 
    www.hp.com/support. If
    prompted, select your country/region, and then click Contact HP for information on
    calling for technical support.
    The Fax Connected to Active Telephone Wall Jack test failed
    Solution:
    • Check the connection between the telephone wall jack and the printer to make
    sure the phone cord is secure.
    • Make sure you use the phone cord that came with the printer. If you do not use
    the supplied phone cord to connect from the telephone wall jack to the printer,
    you might not be able to send or receive faxes. After you plug in the phone cord
    that came with the printer, run the fax test again.
    • Make sure you have correctly connected the printer to the telephone wall jack.
    Using the phone cord supplied in the box with the printer, connect one end to
    your telephone wall jack, then connect the other end to the port labeled 1-LINE
    on the back of the printer. For more information on setting up the printer for
    faxing, see 
    Additional fax setup.
    • If you are using a phone splitter, this can cause faxing problems. (A splitter is a
    two-cord connector that plugs into a telephone wall jack.) Try removing the
    splitter and connecting the printer directly to the telephone wall jack.
    • Try connecting a working phone and phone cord to the telephone wall jack that
    you are using for the printer and check for a dial tone. If you do not hear a dial
    tone, contact your telephone company and have them check the line.
    • Try to send or receive a test fax. If you can send or receive a fax successfully,
    there might not be a problem.
    After you resolve any problems found, run the fax test again to make sure it passes
    and the printer is ready for faxing.
    Solve fax problems 133
     
    						
    							The Phone Cord Connected to Correct Port on Fax test failed
    Solution:Plug the phone cord into the correct port.
    1.Using the phone cord supplied in the box with the printer, connect one end to
    your telephone wall jack, then connect the other end to the port labeled 1-LINE
    on the back of the printer.
    NOTE:If you use the 2-EXT port to connect to the telephone wall jack, you
    cannot send or receive faxes. The 2-EXT port should only be used to
    connect other equipment, such as an answering machine.
    Figure 8-1 Back view of the printer
    1 Telephone wall jack
    2 Use the phone cord supplied in the box with the printer to connect to the 1-LINE
    port
    2.After you have connected the phone cord to the port labeled 1-LINE, run the fax
    test again to make sure it passes and the printer is ready for faxing.
    3.Try to send or receive a test fax.
    • Make sure you use the phone cord that came with the printer. If you do not use
    the supplied phone cord to connect from the telephone wall jack to the printer,
    you might not be able to send or receive faxes. After you plug in the phone cord
    that came with the printer, run the fax test again.
    • If you are using a phone splitter, this can cause faxing problems. (A splitter is a
    two-cord connector that plugs into a telephone wall jack.) Try removing the
    splitter and connecting the printer directly to the telephone wall jack.
    The Using Correct Type of Phone Cord with Fax test failed
    Solution:
    • Make sure you used the phone cord supplied in the box with the printer to
    connect to the telephone wall jack. One end of the phone cord should be
    Chapter 8
    134 Solve a problem
     
    						
    							connected to the port labeled 1-LINE on the back of the printer, and the other
    end to your telephone wall jack.
    1 Telephone wall jack
    2 Use the phone cord supplied in the box with the printer to connect to the 1-LINE
    port
    If the phone cord that came with the printer is not long enough, you can use a
    coupler to extend the length. You can purchase a coupler at an electronics
    store that carries phone accessories. You also need another phone cord, which
    can be a standard phone cord that you might already have in your home or
    office.
    • Check the connection between the telephone wall jack and the printer to make
    sure the phone cord is secure.
    • Make sure you use the phone cord that came with the printer. If you do not use
    the supplied phone cord to connect from the telephone wall jack to the printer,
    you might not be able to send or receive faxes. After you plug in the phone cord
    that came with the printer, run the fax test again.
    • If you are using a phone splitter, this can cause faxing problems. (A splitter is a
    two-cord connector that plugs into a telephone wall jack.) Try removing the
    splitter and connecting the printer directly to the telephone wall jack.
    The Dial Tone Detection test failed
    Solution:
    • Other equipment, which uses the same phone line as the printer, might be
    causing the test to fail. To find out if other equipment is causing a problem,
    disconnect everything from the phone line, and then run the test again. If the
    Dial Tone Detection Test passes without the other equipment, then one or
    more pieces of the equipment is causing problems; try adding them back one at
    a time and rerunning the test each time, until you identify which piece of
    equipment is causing the problem.
    • Try connecting a working phone and phone cord to the telephone wall jack that
    you are using for the printer and check for a dial tone. If you do not hear a dial
    tone, contact your telephone company and have them check the line.
    Solve fax problems 135
     
    						
    							• Make sure you have correctly connected the printer to the telephone wall jack.
    Using the phone cord supplied in the box with the printer, connect one end to
    your telephone wall jack, then connect the other end to the port labeled 1-LINE
    on the back of the printer.
    • If you are using a phone splitter, this can cause faxing problems. (A splitter is a
    two-cord connector that plugs into a telephone wall jack.) Try removing the
    splitter and connecting the printer directly to the telephone wall jack.
    • If your telephone system is not using a standard dial tone, such as some PBX
    systems, this might cause the test to fail. This does not cause a problem
    sending or receiving faxes. Try sending or receiving a test fax.
    • Check to make sure the country/region setting is set appropriately for your
    country/region. If the country/region setting is not set or is set incorrectly, the
    test might fail and you might have problems sending and receiving faxes.
    • Make sure you connect the printer to an analog phone line or you cannot send
    or receive faxes. To check if your phone line is digital, connect a regular analog
    phone to the line and listen for a dial tone. If you do not hear a normal sounding
    dial tone, it might be a phone line set up for digital phones. Connect the printer
    to an analog phone line and try sending or receiving a fax.
    • Make sure you use the phone cord that came with the printer. If you do not use
    the supplied phone cord to connect from the telephone wall jack to the printer,
    you might not be able to send or receive faxes. After you plug in the phone cord
    that came with the printer, run the fax test again.
    After you resolve any problems found, run the fax test again to make sure it passes
    and the printer is ready for faxing. If the Dial Tone Detection test continues to fail,
    contact your telephone company and have them check the phone line.
    The Fax Line Condition test failed
    Solution:
    • Make sure you connect the printer to an analog phone line or you cannot send
    or receive faxes. To check if your phone line is digital, connect a regular analog
    phone to the line and listen for a dial tone. If you do not hear a normal sounding
    dial tone, it might be a phone line set up for digital phones. Connect the printer
    to an analog phone line and try sending or receiving a fax.
    • Check the connection between the telephone wall jack and the printer to make
    sure the phone cord is secure.
    • Make sure you have correctly connected the printer to the telephone wall jack.
    Using the phone cord supplied in the box with the printer, connect one end to
    your telephone wall jack, then connect the other end to the port labeled 1-LINE
    on the back of the printer.
    Chapter 8
    136 Solve a problem
     
    						
    All HP manuals Comments (0)

    Related Manuals for HP Officejet 6500A e All in One E710 User Manual