HP LaserJet P4015n User Manual

Control panel messageDescriptionRecommended action
68.X PERMANENT STORAGE WRITE FAIL
To continue press OKThe storage device is failing to write. Printing
can continue, but there might be some
unexpected behaviors because an error
occurred in permanent storage.Press OK to continue.
If the error does not clear, turn the product off
then on. If the message persists, contact an
HP-authorized service or support provider.
68.X STORAGE ERROR SETTINGS
CHANGED
For help press 
alternates with
68.X STORAGE ERROR...

Control panel messageDescriptionRecommended action
If the error no longer exists, follow these
steps.
1.Install the DIMM and EIO device one at
a time, making sure to turn the product
off and then on as you install each
device.
2.Replace the DIMM or EIO device if you
determine that it causes the error.
3.Reconnect all cables that connect the
product to the network or computer.
8X.YYYY EIO ERRORThe EIO accessory card in slot [X] has
encountered a critical error.1.Turn the product off and then on.
2.Turn...

Control panel messageDescriptionRecommended action
BAD OPTIONAL TRAY CONNECTIONAn optional tray is not connected correctly.Remove the product from the tray, and
reinstall it. Then, turn the product off and then
on.
Canceling...The product is canceling a job. The message
continues while the job is stopped, the paper
path is cleared, and any remaining incoming
data on the active data channel is received
and discarded.No action is necessary.
CANNOT DUPLEX CLOSE REAR DOOR
For help press The rear door must be...

Control panel messageDescriptionRecommended action
alternates with

DATE/TIME=YYYY/MMMM/DD HH:MM
Press OK to continue
To skip press 
.
The current date and time.Set the date and time or press the stop button
 to skip.
Deleting...Product is deleting a stored job.No action is necessary.
DUPLEXER ERROR REMOVE DUPLEXER
Install duplexer with power offThe optional duplexer has an error.Turn off the product and reattach the optional
duplexer. (Any print jobs at the product might
be lost.)
EIO  DISK NOT...

Control panel messageDescriptionRecommended action
IncorrectThe wrong PIN number was entered.Reenter PIN number.
INFLATE FAILURE SEND FULL RFU ON
 PORTAn error occurred during a firmware upgrade.Contact an HP-authorized service or support
provider.
InitializingIndividual tasks are being initialized.No action is necessary.
INSERT OR CLOSE TRAY 
For help press The specified tray is open or missing.Insert or close the tray for printing to continue.
INSTALL BLACK CARTRIDGE
For help press The print cartridge...

Control panel messageDescriptionRecommended action
To use another tray press OK
alternates with
LOAD ENVELOPE FEEDER [TYPE] [SIZE]
For help press If paper is already in the envelope feeder,
press OK to print.
To use another tray, remove paper from the
envelope feeder, and then press OK to print.
LOAD TRAY 1 [TYPE] [SIZE]
To continue press OK
alternates with
LOAD TRAY 1 [TYPE] [SIZE]
For help press Tray 1 is empty.Load Tray 1 with the requested paper.
If the paper is already in the Tray 1, press the
help...

Control panel messageDescriptionRecommended action
To use another tray press OK
alternates with
MANUALLY FEED [TYPE] [SIZE]
For help press 
MANUALLY FEED OUTPUT STACK
Then press OK to print second sidesThe first side of a manual duplex job has been
printed and the product is waiting for you to
insert the output stack to complete the
second side.1.Load the output stack into Tray 1,
maintaining the same orientation with
printed side down.
2.To continue printing, press OK.
No job to cancelThe stop button...

Control panel messageDescriptionRecommended action
5.Reinstall the fuser and the rear output
bin.
6.Turn the product on.
PERFORM PRINTER MAINTENANCE
For help press 
alternates with

The product is due for regular maintenance.Contact your service representative to
schedule maintenance. Continue printing
until maintenance is performed.
Performing upgradeFirmware is being upgraded.No action is necessary.
Please waitThe product is going offline.No action is necessary.
Printing...ENGINE TESTThe product is...

Control panel messageDescriptionRecommended action
RFU LOAD ERROR SEND FULL RFU ON
 PORTAn error occurred during a firmware upgrade.Contact an HP-authorized service or support
provider.
ROM DISK DEVICE FAILURE
To clear press OKThe specified device has failed.Press OK to continue.
ROM DISK FILE OPERATION FAILED
To clear press OKA command attempted an illogical operation.Press OK to continue.
ROM DISK FILE SYSTEM IS FULL
To clear press OKThe specified file system is full and cannot be
written to.Press OK...

Control panel messageDescriptionRecommended action
TOO MANY TRAYS INSTALLEDYou have installed more optional trays than
the product supports.
The product can accept up to four optional
500-sheet trays, or it can accept one optional
1,500-sheet tray and up to three optional 500-
sheet trays, for a total of up to four optional
trays.Remove one of the optional trays.
TRAY  [TYPE] [SIZE]
To change size or type press OK
alternates with
TRAY  [TYPE] [SIZE]
To accept settings press This message states the...