Home > HP > Printer > HP LaserJet P4015n User Manual

HP LaserJet P4015n User Manual

Here you can view all the pages of manual HP LaserJet P4015n User Manual. The HP manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 141

4.Open the access door by pulling on the metal tab.
5.Locate the USB ports near the bottom of the formatter board. Insert the USB device into one of the
ports.
6.Close the access door, and press firmly until it snaps into place.
ENWW Install memory, internal USB devices, and external print server cards 129
 

Page 142

7.Reinstall the right-side panel. Align the tabs on the panel with the slots in the product, and push
the panel toward the front of the product until it latches into place.
8.Reconnect the interface cables and the power cord.
9.Turn the product on.
130 Chapter 9   Manage and maintain the product ENWW
 

Page 143

Install HP Jetdirect print server cards
Follow these procedures to install or remove an EIO card.
Install an HP Jetdirect print server card
1.Turn off the product.
2.Remove the two screws and cover plate from the EIO slot on the back of the product.
NOTE:Do not discard the screws or the cover plate. Save them for future use if you remove the
EIO card.
3.Install the EIO card in the EIO slot and tighten the screws.
ENWW Install memory, internal USB devices, and external print server cards 131
 

Page 144

4.Connect the network cable to the EIO card.
5.Turn on the product, and then print a configuration page to verify that the new EIO device is
recognized. See 
Print the information and show-me-how pages on page 104.
NOTE:When you print a configuration page, an HP Jetdirect configuration page that contains network
configuration and status information also prints.
Remove an HP Jetdirect print server card
1.Turn off the product. 
2.Disconnect the network cable from the EIO card.
3.Loosen the two screws from...

Page 145

Clean the product
During the printing process, paper, toner, and dust particles can accumulate inside the product. Over
time, this buildup can cause print-quality problems, such as toner specks or smearing (see 
Solve print-
quality problems on page 181).
Clean the exterior
Use a soft, damp, lint-free cloth to wipe dust, smudges, and stains off of the exterior of the device.
Clean the paper path
1.
Press Menu .
2.Press the down arrow 
 to highlight CONFIGURE DEVICE, and then press OK.
3.Press the down...

Page 146

Upgrade the firmware
This product has remote firmware update (RFU) capability. Use this information to upgrade the product
firmware.
Determine the current firmware version
1.
Press Menu .
2.Press the down arrow
 to highlight INFORMATION, and then press OK.
3.Press the down arrow 
 to highlight PRINT CONFIGURATION, and then press OK to print.
The firmware datecode is listed on the Configuration page in the section called Device Information.
The firmware datecode has this format: YYYYMMDD XX.XXX.X. The...

Page 147

c.Select the box labeled Enable folder view for FTP sites.
d.Click OK.
2.Print a configuration page and note the TCP/IP address shown on the EIO Jetdirect page.
3.Open a browser window.
4.In the address line of the browser, type
ftp://
, where  is the address of the product. For example, if the TCP/IP address is
192.168.0.90, type
ftp://192.168.0.90
.
5.Locate the downloaded .RFU file for the product.
6.Drag and drop the .RFU file onto the PORT1 icon in the browser window.
NOTE:The product turns off and...

Page 148

11.The download process begins and the firmware is updated on the product. This can take
approximately five minutes. Let the process finish without further interaction with the product or
computer.
NOTE:The product automatically turns off and then on again after processing the upgrade.
12.At the command prompt, type: bye to exit the ftp command.
13.At the command prompt, type: exit to return to the Windows interface.
Use HP Web Jetadmin to upgrade the firmware
This procedure requires that you install HP...

Page 149

Use Microsoft Windows commands to upgrade the firmware
To update the firmware by using a network connection, follow these instructions.
1.Click Start, click Run, and then type cmd to open the command window.
2.Type the following:
copy /B FILENAME> \\COMPUTERNAME>\SHARENAME>
, where  is the name of the .RFU file (including the path),  is
the name of the computer from which the product is being shared, and  is the
product share name. For example:
C:\>copy /b C:\LJP4015.RFU \\YOUR_SERVER\YOUR_COMPUTER
....

Page 150

10.In the Device Tools drop-down list, select Jetdirect Firmware Update again.
11.On the HP Jetdirect firmware page, the new firmware version is listed under Jetdirect Firmware
Available on HP Web Jetadmin. Click the Update Firmware Now button to update the Jetdirect
firmware.
138 Chapter 9   Manage and maintain the product ENWW
 
Start reading HP LaserJet P4015n User Manual

Related Manuals for HP LaserJet P4015n User Manual

All HP manuals