HP LaserJet P4015n User Manual

Load envelopes
Load envelopes into Tray 1 or the optional envelope feeder with the front of the envelope facing up, and
the short, postage-edge leading into the product.
12
ENWWLoad trays 79
 

Load Tray 1 
NOTE:The product might print at a slower speed when using Tray 1.
CAUTION:To avoid jams, do not load trays while the product is printing. Do not fan the paper. Fanning
can cause misfeeds.
1.Open Tray 1.
2.Pull out the tray extension.
3.Load the paper into the tray. Make sure that the paper fits under the tabs and below the maximum-
height indicators.
NOTE:For information about loading paper that requires a specific orientation, see Paper
orientation for loading trays on page 78.
2
80 Chapter...

4.Adjust the side guides so that they lightly touch the paper stack but do not bend the paper.
2
Load Tray 2 or an optional 500-sheet tray
CAUTION:To avoid jams, do not load trays while the product is printing.
CAUTION:Do not fan the paper. Fanning can cause misfeeds.
1.Pull the tray out and lift up slightly to remove it from the product.
2.Pinch the release that is located on the left guide and slide the side guides to the correct paper
size.
A5
J
IS B5EXEC
A4
LTR/LGL
ENWWLoad trays 81
 

3.Pinch the release that is located on the rear paper guide and slide it to the correct paper size.
5 A5 B  S IJCE
X ERT L4 A
4.Load the paper into the tray. Make sure that the stack is flat at all four corners and that the top of
the stack is below the maximum-height indicators.
NOTE:For information about loading paper that requires a specific orientation, see Paper
orientation for loading trays on page 78.
5.Slide the tray completely into the product.
82 Chapter 6   Paper and print media ENWW
 

Load an optional 1,500-sheet tray
The optional 1,500 sheet tray adjusts for Letter, A4, and Legal sizes. The product automatically senses
which size is loaded if the tray guides are correctly adjusted.
CAUTION:To avoid jams, do not load trays while the product is printing.
CAUTION:Do not fan the paper. Fanning can cause misfeeds.
1.Press the release and open the door of the 1,500-sheet tray.
2.If paper is in the tray, remove it. When paper is in the tray, the guides cannot be adjusted.
3.Pinch the guides...

4.Load the paper into the tray. Load complete reams at one time. Do not divide reams into smaller
sections.
NOTE:For information about loading paper that requires a specific orientation, see Paper
orientation for loading trays on page 78.
5.Make sure that the height of the stack does not exceed the maximum-height indicators on the
guides and that the front edge of the stack is aligned with the arrows.
6.Close the door on the tray.
84 Chapter 6   Paper and print media ENWW
 

Configure trays
The product automatically prompts you to configure a tray for type and size in the following situations:
●When you load paper into the tray
●When you specify a particular tray or paper type for a print job through the printer driver or a software
program and the tray is not configured to match the print-job’s settings
NOTE:The prompt does not appear if you are printing from Tray 1 and Tray 1 is configured for ANY
SIZE and ANY TYPE.
NOTE:If you have used other HP LaserJet product models,...

Configure a tray by using the Paper Handling menu
You can also configure the trays for type and size without a prompt from the product.
1.
Press Menu 
.
2.Press the down arrow 
 to highlight PAPER HANDLING, and then press OK.
3.Press the down arrow 
 to highlight the size or type setting for the desired tray, and then press
OK.
4.Press the down arrow 
 to highlight the size or type. To specify a custom size, first press the down
arrow 
 to highlight the correct unit of measure. Then set the X and Y...

Use paper output options 
The product has four output locations: the top (standard) output bin, the rear output bin, the optional
stacker or stapler/stacker, and the optional 5-bin mailbox.
Print to the top (standard) output bin
The top output bin collects paper face-down, in the correct order. The top output bin should be used for
most print jobs, including transparencies. To use the top output bin, be sure that the rear output bin is
closed. To avoid jams, do not open or close the rear output bin while...

Opening the rear output bin makes the duplexer (if installed) and the top output bin unavailable. To avoid
jams, do not open or close the rear output bin while the product is printing.
Print to the optional stacker or stapler/stacker
The optional stacker or optional stapler/stacker can hold up to 500 sheets of paper (20-lb paper). The
stacker accepts standard and custom paper sizes. The stapler/stacker accepts standard and custom
paper sizes, but only Letter, Legal, and A4 sizes can be stapled. Do not...