HP LaserJet P4015n User Manual

6.Align the print cartridge with the tracks inside the product, insert the print cartridge until it is firmly
seated, and then close the top cover.
After a short time, the control panel should display Ready.
7.Installation is complete. Place the used print cartridge in the box in which the new cartridge arrived.
See the enclosed recycling guide for recycling instructions.
8.If you are using a non-HP print cartridge, check the product control panel for further instructions.
For additional help, go to...

Load staples
Load staples if the product control-panel display prompts you with a message. If the stapler runs out of
staples, jobs continue to print to the stapler/stacker, but they are not stapled.
1.On the right side of the stapler/stacker, turn the stapler unit toward the front of the product until the
unit clicks into the open position. Grasp the blue staple-cartridge handle and pull the cartridge out
of the stapler unit.
2.Insert the new staple cartridge into the stapler unit and rotate the stapler...

Perform preventive maintenance
To ensure optimum performance from the product, replace certain parts when the PERFORM PRINTER
MAINTENANCE message appears on the control-panel display.
The maintenance message appears after printing 225,000 pages. The message can be temporarily
cleared for approximately 10,000 pages by using the CLEAR MAINTENANCE MESSAGE item on the
Resets submenu. To check the number of pages printed since new maintenance-kit components were
installed, print either a configuration page or...

Install memory, internal USB devices, and external print
server cards
Overview
The formatter has the following open slots and ports for expanding the products capabilities:
●One dual inline memory module (DIMM) slot for upgrading the product with more memory
●Two internal USB ports for adding fonts, languages, and other third-party solutions
●One external I/O (EIO) slot for adding an external print server, an external hard disk, or a parallel
port
If the product already has an embedded HP Jetdirect print...

If you have not already done so, print a configuration page to find out how much memory is installed in
the product before adding more memory. See 
Print the information and show-me-how pages
on page 104.
1.After the configuration page has printed, turn the product off and disconnect the power cord.
2
1
2.Disconnect all interface cables.
3.Remove the right-side panel by sliding it towards the rear of the product to unlatch it.
ENWW Install memory, internal USB devices, and external print server cards 123
 

4.Open the access door by pulling on the metal tab.
5.Remove the DIMM from the antistatic package.
CAUTION:To reduce the possibility of damage caused by static electricity, always wear an
electrostatic discharge (ESD) wrist strap or touch the surface of the antistatic package before
handling DIMMs.
6.Hold the DIMM by the edges, and align the notches on the DIMM with the DIMM slot. (Check that
the locks on each side of the DIMM slot are open.)
124 Chapter 9   Manage and maintain the product ENWW
 

7.Press the DIMM straight into the slot, and press firmly. Make sure the locks on each side of the
DIMM snap into place.
1
22
NOTE:To remove a DIMM, first release the locks.
11
2
8.Close the access door, and press firmly until it snaps into place.
ENWW Install memory, internal USB devices, and external print server cards 125
 

9.Reinstall the right-side panel. Align the tabs on the panel with the slots in the product, and push
the panel toward the front of the product until it latches into place.
10.Reconnect the interface cables and the power cord.
11.Turn the product on.
Check DIMM installation
After installing the DIMM, make sure that the installation was successful.
1.Turn the product on. Check that the Ready light is illuminated after the product has gone through
the startup sequence. If an error message appears, a DIMM...

Use the following guidelines if you use the page description language (PDL) ability to mark resources
as permanent. For technical details, see an appropriate PDL reference for PCL or PS.
●Mark resources as permanent only when it is absolutely necessary that they remain in memory
while the product is turned on.
●Send permanent resources to the product only at the beginning of a print job and not while the
product is printing.
NOTE:Overusing permanent resources or downloading them while the product is...

Install internal USB devices
The product has two internal USB ports.
1.Turn the product off and disconnect the power cord.
2
1
2.Disconnect all interface cables.
3.Remove the right-side panel by sliding it towards the rear of the product to unlatch it.
128 Chapter 9   Manage and maintain the product ENWW