HP LaserJet 9059 MFP User Manual

Set document effects
To perform the following tasks, open the printer driver and click the Effects tab.
How do ISteps to perform
Scale a page to fit on a selected paper sizeClick Print document on , and then select a size from the drop-
down list.
Scale a page to be a percent of the actual sizeClick  % of actual size , and then type the percent or adjust the
slider bar.
Print a watermarka) Select a watermark from the  Watermarks drop-down list.
b) To print the watermark on the first page only, click...

Set job storage options
To perform the following tasks, open the printer driver and click the Job Storage tab.
How do ISteps to perform
Print one copy for proof before printing all the copiesIn the Job Storage Mode  area, click Proof and Hold . The
product prints the first copy only. A message appears on the
product control panel that prompts you to print the rest of the
copies.
Temporarily store a private job on the product and print it latera) In the  Job Storage Mode  area, click Personal Job . b) In...

How do ISteps to perform
Change the number of copies that are printed
NOTE:If the software program that you are using does not
provide a way to print a particular number of copies, you can
change the number of copies in the driver.
Changing this setting affects the number of copies for all print
jobs. After your job has printed, restore this setting to the
original value.Open the Paper/Output  section, and then enter the number of
copies to print. If you select  2 or more copies, you can select
the...

Staple documents
NOTE:Stapling features are only available if the stapler/stacker or multifunction finisher are attached
to the MFP.
Set the stapler at the cont rol panel for printed jobs
You can usually select the stapler in your software program or printer driver, although some options
might be available only in the printer driver. See 
Change printer-driver settings for Windows
on page 53 for more information. Where and how you make selections depends on your program or
driver. If the stapler cannot...

Configure the device to stop or continue when the staple cartridge is empty
You can specify whether the MFP stops printing when the staple cartridge is empty or if it continues
printing but does not staple the jobs.
1.Scroll to and touch  Administration.
2. Scroll to and touch  Device Behavior.
3. Scroll to and touch  Stapler/Stacker or Multifunct. Finisher .
4. Touch  Staples Out .
5. Touch the option that you want to use:
●Select 
Stop to stop all printing until the staple cartridge is replaced.
●...

3.On the empty staple cartridge, pull up on the green tab, and then pull the empty cartridge out.
Figure 7-3   Load staples in the stapler/stacker (3 of 5)
4.Insert the new staple cartridge, and push down on the green tab so that the cartridge locks into
place.
Figure 7-4   Load staples in the stapler/stacker (4 of 5)
5.Close the stapler unit door and push the stapler/stacker back into place.
Figure 7-5   Load staples in the stapler/stacker (5 of 5)
Load staples in the multifunction finisher
1.Open the...

2.Slide the stapler unit toward you.
Figure 7-7   Load staples in the multifunction finisher (2 of 8)
3.Turn the large green knob until the blue dot appears in the window of the stapler unit.
Figure 7-8   Load staples in the multifunction finisher (3 of 8)
4.Turn the small green knob at the top of the stapler unit clockwise until the staple cartridge moves
to the left of the stapler unit.
Figure 7-9   Load staples in the multifunction finisher (4 of 8)
CAUTION: The blue dot must appear in the window of...

6.Insert the new staple cartridge so that it locks into place.
Figure 7-11   Load staples in the multifunction finisher (6 of 8)
7.Slide the stapler unit into the finisher.
Figure 7-12   Load staples in the multifunction finisher (7 of 8)
8.Close the stapler unit door and realign the multifunction finisher against the MFP.
Figure 7-13   Load staples in the multifunction finisher (8 of 8)
104 Chapter 7   Print tasks ENWW
 

Cancel a print job
You can stop a print request by using the control panel or by using the software program. For instructions
about how to stop a print request from a computer on a network, see the online Help for the specific
network software.
NOTE:It can take some time for all printing to clear after you have canceled a print job.
Stop the current print job from the control panel
1.Press  Stop on the control panel.
2. On the touchscreen, on the  Device Has Been Paused screen, touch Cancel current job...

Print on envelopes
Envelopes must be printed from tray 1, which holds up to 10 envelopes. Printing performance depends
on the construction of the envelope. Always test a few sample envelopes before purchasing a large
quantity. For envelope specifications, see 
Supported paper and print media sizes on page 77 or go to
www.hp.com/support/ljm9059mfp .
CAUTION:Envelopes with clasps, snaps, windows, coated linings, exposed self-stick adhesives, or
other synthetic materials can severely damage the MFP. Do not...