HP LaserJet 9059 MFP User Manual

7.Adjust the front (X) paper guide by pressing the tab on the guide and slide the guide until it gently
touches the paper.
Figure 6-20  Load custom media in trays 2, 3, and 4 (5 of 6)
8.Note the orientation of the paper, as well as the value of the X dimension and the Y dimension.
The X and Y dimensions are marked in the tray. You will need this information for a later step.
NOTE: When loading tray 4, make sure that the paper guide lock is in the up position.
9.Close the tray. The MFP control panel might...

Configure trays
The MFP might automatically prompt you to configure a tray for type and size when you load media into
the tray.
The following message appears on the control panel: Tray  [type] [size] To change size or type,
touch “Modify”. To accept, touch “OK”. .
NOTE:The prompt does not appear if you are printing from tray 1 and tray 1 is configured for  Any
Size  and Any Type .
NOTE:If you have used other HP LaserJet printer models, you might be accustomed to configuring
tray 1 to  First mode or...

Source
To print by Source select a specific tray from MFP to pull fr om. The MFP tries to print from this tray, no
matter what type or size is loaded. If you select a tray that is configured for a type or size that does not
match your print job, the MFP does not print automatically. Instead, it waits for you to load the tray with
the type or size of print media for your print job. If you load the tray, the MFP begins printing.
Type and Size
Printing by  Type or Size  means that you want the MFP to pull...

Select the output bin
The MFP has at least two output bin locations: the ADF output bin (1) and an output bin on the output
device.
Figure 6-22  Output bins
It is recommended that you select an output location through the software program or printer driver.
Stacker or stapler/stacker output bins
If you choose the 3,000-sheet stacker or 3,000-sheet stapler/stacker, the output bins are the upper bin
(2) (face up) and the lower bin (3) (face down).
The upper bin (face-up) (2) is the top bin on the stacker...

Select an output location
Printing
It is recommended that you select an output location (bin) through your program or driver. Where and
how you make selections depends on your program or driver, set the default output location from the
MFP control panel.
1.Scroll to and touch  Administration.
2. Touch  Default Job Options .
3. Touch  Default Print Options .
4. Touch  Output Bin .
5. Touch the desired output bin.
Copying
You can set and override the current default output location (bin) from the MFP...

92 Chapter 6   Paper and print mediaENWW
 

7 Print tasks
●Media type and tray loading
●
Use features in the Windows printer driver
●
Staple documents
●
Cancel a print job
●
Print on envelopes
●
Job storage features for print
ENWW 93
 

Media type and tray loading
Minimum media dimensions are 98 x 191 mm (3.8 x 7.5 inches).
Maximum media dimensions are 312 x 470 mm (12.3 x 18.5 inches).
Table 7-1  Tray 1 media information
Media typeMedia specificationsMedia quantityDriver settingsPaper orientation
Paper and cardstock,
standard sizes64 g/m2 (17 lb) bond to
216 g/m2 (58 lb) bond
Two-sided printing: 64
g/m
2 (17 lb) bond to 199
g/m2 (53 lb) bond
Maximum stack height:
10 mm (0.6 inch)
Equivalent to 100
sheets of 75 g/m
2 (20
lb) bond.
Plain...

Media typeMedia specificationsMedia quantityDriver settingsPaper orientation
Heavy64 g/m2 (17 lb) bond to
199 g/m2 (53 lb) bond
Up to 2000 sheetsLight glossy, glossy, or
heavy glossySide to be printed on
facing up
Glossy 64 g/m2 (17 lb) bond to
199 g/m2 (53 lb) bond Up to 2000 sheets Light glossy, glossy, or
heavy glossy Side to be printed on
facing up
Table 7-3
  Tray 4 media information (continued)
ENWW Media type and tray loading 95
 

Use features in the Windows printer driver
Open the printer driver
How do ISteps to perform
Open the printer driverOn the File menu in the software program, click  Print. Select
the printer, and then click  Properties or Preferences.
Get help for any printing option Click the ? symbol in the upper-right corner of the printer driver,
and then click any item in the printer driver. A pop-up message
displays that provides information about the item. Or, click
Help  to open the online Help.
Use printing...