HP LaserJet 9059 MFP User Manual

Supported paper and print media sizes
This product supports a number of paper sizes, and it adapts to various media.
NOTE:To obtain best print results, select the appropriate paper size and type in your print driver before
printing.
Table 6-1   Supported paper and print media sizes
SizeDimensionsTray 1, Letter
R, A4Trays 2 and 3,
Letter R, A4Tray 4, Letter
R, A4Stapler /
Stacker lower
bin
Letter216 x 279 mm (8.5 x 11 in.)
Legal216 x 356 mm (8.5 x 14 in.)
A4210 x 297 mm (8.27 x 11.69 in.)
Executive184 x...

SizeDimensionsTray 1, mailbox,
stackerTrays 2, 3, 4Stapler
Double Post
Card148 x 200 mm (5.83 x 7.87 in.)  
Postcard (US)88.9 x 139.7 mm (3.5 x 5.5 in.)  
Postcard
(European)105 x 148 mm (4.13 x 5.83 in.)  
Table 6-2
  Supported envelopes and postcards (continued)
78 Chapter 6   Paper and print media ENWW
 

Custom paper sizes
This product supports a variety of custom paper sizes. Supported custom sizes are sizes that are within
the minimum- and maximum-size guidelines for the product but are not listed in the supported paper
sizes table. When using a supported custom size, specify the custom size in the print driver, and load
the paper in a tray that supports custom sizes.
ENWW Custom paper sizes 79
 

Special paper or print media guidelines
This product supports printing on special media. Use the following guidelines to obtain satisfactory
results. When using special paper or print media, be sure to set the type and size in your print driver to
obtain the best print results.
CAUTION:HP LaserJet printers use fusers to bond dry toner particles to the paper in very precise
dots. HP laser paper is designed to withstand this extreme heat. Using inkjet paper not designed for this
technology could damage...

Load paper and print media
This section contains information about loading standard- and custom-size media into the four input
trays.
CAUTION:To avoid a jam, never add or remove paper from tray 1 or open tray 2, tray 3, or tray 4
while printing or copying from that tray. To avoid damaging the MFP, print labels, envelopes, and
transparencies from tray 1 only. Send labels, envelopes, and transparencies to the upper bin. Print on
only one side of labels, envelopes, and transparencies.
Load tray 1
Tray 1...

NOTE:If printing on A3- or 11 x 17-size paper, or other long media, also pull out the tray extension
until it stops.
Load trays 2, 3, and 4
Trays 2 and 3 hold up to 500 sheets of standard media. Tray 4 holds up to 2,000 sheets of standard
media. For information about paper specifications, see 
Supported paper and print media sizes
on page 77.
Load detectable standard-size paper in trays 2, 3, and 4
Follow this procedure to load detectable standard-size paper in the tray. The following are the detectable...

2.Adjust the left (Y) paper guide by pressing the tab on the guide and set the guide to the correct
paper size.
Figure 6-5   Load trays 2, 3, and 4 (2 of 6)
3.Adjust the front (X) paper guide by pressing the tab on the guide and set the guide to the correct
paper size.
Figure 6-6   Load trays 2, 3, and 4 (3 of 6)
4.Load (orient) the paper according to size.
Figure 6-7   Load trays 2, 3, and 4 (4 of 6)
5.Set the Custom/Standard switch to Standard.
Figure 6-8   Load trays 2, 3, and 4 (5 of 6)
ENWW Load...

6.Close the tray. The MFP control panel might show the tray media type and size. If the configuration
is not correct, touch  Modify on the control panel. If the configuration is correct, touch  OK.
Figure 6-9   Load trays 2, 3, and 4 (6 of 6)
Load undetectable standard-size paper in trays 2, 3, and 4
Follow this procedure to load undetectable standard-size paper in the tray. The following are the
undetectable sizes:
●8K
● 16K
● Statement
● JIS Executive
● 8.5 x 13 (216 x 330 mm).
CAUTION:
To avoid a jam,...

5.Adjust the left paper guide by pressing the tab on the guide and slide the guide until it gently touches
the paper
Figure 6-12  Load undetectable standard-size paper in trays 2, 3, and 4 (3 of 6)
6.Adjust the front paper guide by pressing the tab on the guide and slide the guide until it gently
touches the paper.
Figure 6-13  Load undetectable standard-size paper in trays 2, 3, and 4 (4 of 6)
NOTE: When loading tray 4, make sure that the paper guide lock is in the up position.
7.Set the Custom/Standard...

CAUTION:To avoid a jam, never add or remove paper from a tray while printing from that tray.
1.Open the tray until it stops.
Figure 6-16   Load custom media in trays 2, 3, and 4 (1 of 6)
2.Press the tab on the front (X) paper guide and slide the guide all the way out.
3. Press the tab on the left (Y) paper guide and slide the guide all the way out.
4. Load (orient) the paper according to size.
Figure 6-17   Load custom media in trays 2, 3, and 4 (2 of 6)
5.Set the Custom/Standard switch to Custom.
Figure...