HP LaserJet 9059 MFP User Manual

Menu itemSub-menu itemSub-menu itemValues and Description
 IPV4 SettingsConfig MethodSpecifies the method by which TCP/IPv4 parameters
for the HP Jetdirect print server will be configured.
Bootp: Use BootP (Bootstrap Protocol) for automatic
configuration from a BootP server.
DHCP  (Default): Use DHCP (Dynamic Host
Configuration Protocol) for automatic configuration
from a DHCPv4 server. If selected and a DHCP lease
exists,  DHCP Release  and DHCP Renew menus are
available to set DHCP lease options.
Auto...

Menu itemSub-menu itemSub-menu itemValues and Description
  Default IPSpecify the IP address to default to when the print
server is unable to obtain an IP address from the
network during a forced TCP/IP reconfiguration (for
example, when manually configured to use BootP or
DHCP).
Auto IP: A link-local IP address 169.254.x.x is set.
Legacy : The address 192.0.0.192 is set, consistent
with older HP Jetdirect devices.
  Primary DNSSpecify the IP address (n.n.n.n) of a Primary DNS
Server.
  Secondary...

Menu itemSub-menu itemSub-menu itemValues and Description
 Proxy Server Specifies the proxy server to be used by embedded
applications in the device. A proxy server is typically
used by network clients for Internet access. It caches
Web pages, and provides a degree of Internet security,
for those clients.
To specify a proxy server, enter its IPv4 address or
fully-qualified domain name. The name can be up to
255 octets.
For some networks, you may need to contact your
Independent Service Provider (ISP) for...

Menu itemSub-menu itemSub-menu itemValues and Description
SecurityPrint Sec Page Yes: Prints a page that contains the current security
settings on the HP Jetdirect print server.
No  (default): A security settings page is not printed.
Secure Web For configuration management, specify whether the
embedded Web server will accept communications
using HTTPS (Secure HTTP) only, or both HTTP and
HTTPS.
HTTPS Required (Default) : For secure, encrypted
communications, only HTTPS access is accepted. The
print...

Menu itemSub-menu itemSub-menu itemValues and Description
  SNMP TestThis test checks operation of SNMP communications
by accessing predefined SNMP objects on the device.
Select Yes to choose this test, or  No to not choose it.
  Select All TestsUse this item to select all available embedded tests.
Select  Yes to choose all tests. Select  No to select
individual tests.
  Data Path TestThis test helps to identify data path and corruption
problems on an HP postscript level 3 emulation device.
It sends a...

Menu itemSub-menu itemSub-menu itemValues and Description
 Ping Results Use this item to view the ping test status and results
using the control panel display. You can select the
following items:
Packets SentShows the number of packets (0 - 65535) sent to the
remote host since the most recent test was initiated or
completed.
Packets ReceivedShows the number of packets (0 - 65535) received from
the remote host since the most recent test was initiated
or completed.
Percent LostShows the percent of ping...

Menu itemSub-menu itemSub-menu itemValues and Description
Link Speed  The link speed and communication mode of the print
server must match the network. The available settings
depend on the device and installed print server. Select
one of the following link configuration settings:
CAUTION:If you change the link setting, network
communications with the print server and network
device might be lost.
Auto  (default): The print server uses auto-negotiation
to configure itself with the highest link speed and...

Fax Setup
Administration > Initial Setup > Fax Setup
NOTE:This menu is only available if the HP LaserJet Analog Fax Accessory 300 is installed.
Table 2-11  Fax Setup menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Required SettingsCountry/Region (Countries/regions
listed)Configure the settings that are legally
required for outgoing faxes.
Date/Time  
Fax Header
InformationPhone Number
Company Name 
PC Fax Send    Disabled
Enabled (default)Use this feature to enable or disable PC Fax
Send. PC...

Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Send Settings Fax Dial Volume Off
Low (default)
HighUse this feature to set the volume of the tones
that you hear while the device dials the fax
number.
Error Correction
Mode Enabled (default)
DisabledWhen Error Correction Mode is enabled and
an error occurs during fax transmission, the
device sends or receives the error portion
again.
JBIG Compression Enabled (default)
DisabledJBIG compression reduces fax-transmission
time, which can result in...

Menu itemSub-menu itemSub-menu itemValuesDescription
 Redial Interval The range is between
1 and 5 minutes. The
factory default is 5
minutes.Use this feature to specify the number of
minutes between dialing attempts if the
recipient number is busy or not answering.
Detect Dial Tone Enabled
Disabled (default)Use this feature to specify whether the device
should check for a dial tone before sending a
fax.
Dialing Prefix Off (default)
CustomUse this feature to specify a prefix number
that must be dialed...