HP Color LaserJet CM1017 User Manual

Networking tab
This tab allows the network administrator to control MFP network-related settings when it is connected
to an IP-based network.
●IP Configuration: Sets the IP configuration.
●Advanced: Enables network features such as SLP Config, DHCP, BOOTP, and AutoIP.
●mDNS: Sets the mDNS. These settings to turn on or off Rendezvous or Bonjour discovery.
●SNMP: Sets SNMP protocols.
Other links found in HP ToolboxFX
Internet access is required to use any of these links. When using a dial-up connection and...

Manage supplies
For warranty information about these supplies, see Print Cartridge Limited Warranty Statement.
Supplies life
The life of a print cartridge depends on the amount of toner that print jobs require. When printing text at
approximately 5% coverage, a cyan, magenta, or yellow print cartridge for the HP Color LaserJet
CM1015/CM1017 MFP lasts an average of 2,000 pages, and a black print cartridge lasts an average of
2,500 pages. A typical business letter has 5% coverage.
Check and order supplies...

Check and order supplies using HP Solution Center
In HP Solution Center, select the MFP. The device status page shows supplies information. To order
use the HP ToolboxFX.
Supplies Storage Guidelines
Follow these guidelines for storing print cartridges:
●Do not remove the print cartridge from its package until it is ready for use.
CAUTION
To prevent damage, do not expose the print cartridge to light for more than a
few minutes.
● See Table C-5 Environmental specifications
 for operating and storage...

HP anti-counterfeit supplies Web site
Visit the HP anti-counterfeit supplies Web site at http://www.hp.com/go/anticounterfeit if the supplies
status gauges or HP ToolboxFX indicates that the print cartridge is not an HP print cartridge and you
think that it is genuine.
160 Chapter 13   Managing and maintaining the multifunction peripheral (MFP) ENWW
 

Clean the scanner glass
Dirty glass from debris may cause scan and copy image defects.
1.Turn device off, unplug the power cord from the electrical socket, and raise the lid.
2. Clean the glass by using a soft lint-free cloth that has been moistened with nonabrasive glass
cleaner.
CAUTION Do not use abrasives, acetone, benzen e, ammonia, ethyl alcohol, or carbon
tetrachloride on any part of the device; these can damage the device. Do not place liquids
directly on the glass. They might seep under it and...

Clean the MFP
During the printing process, paper, toner and dust particles can accumulate inside the MFP. Over time,
this buildup can cause print-quality problems such as toner specks or smearing. This MFP has a cleaning
mode that can correct and prevent these types of problems.
Clean the paper path using HP ToolboxFX
NOTEUse the following procedure to clean the paper path using the HP ToolboxFX. To clean
the engine when the computer is running an operating system that does not support
HP ToolboxFX,...

Cartridge-out override
The HP Color LaserJet CM1015/CM1017 MFP displays an Order supplies message when a cartridge
is running low and a  Replace supplies message when a cartridge has been depleted.  To ensure
optimal print quality, HP recommends replacing a cartridge when the  Replace supplies  message
is displayed.  Replacing the cartridge at this point can help prevent waste of media or other cartridges
when one cartridge produces poor print quality.
The Cartridge-out override feature allows the MFP...

Change print cartridges
When a print cartridge approaches the end of useful life, the control panel displays a message
recommending ordering a replacement. The MFP can continue to print using the current print cartridge
until the control panel displays a message instructing cartridge replacement.
The MFP uses four colors and has a different print cartridge for each color: black (K), cyan (C), magenta
(M), and yellow (Y).
NOTEIn order to print, this MFP requires all print cartridges to be installed....

2.Remove the used print cartridge from the MFP.
3.Remove the new print cartridge from the bag. Place the used print cartridge in the bag for recycling.
4.Grasp both sides of the print cartridge by the blue handles and distribute the toner by gently rocking
the print cartridge from side to side.
CAUTION Do not touch the shutter or the surface of the roller.
ENWW Change print cartridges 165
 

5.Remove the shipping locks and the shipping tape from the new print cartridge. Discard the shipping
tape and shipping locks according to local regulations.
6.Align the print cartridge with the tracks inside the MFP, and using the handles, insert the print
cartridge until it is firmly seated.
7.Firmly close the front door.
After a short time, the control panel should display  Ready.
NOTE If a cartridge is in the wrong slot or is the wrong type for the MFP, the control panel
displays one of the following...