HP Color LaserJet CM1017 User Manual

Class A Network AddressNetwork 15xxxxxxxxx
Example of a node’s IP Address
on Subnet 12101257
Example of a node’s IP Address
on Subnet 254210 254 64 2
The Class A IP network address 210 has been assigned to company ABC. To allow additional networks
at company ABC’s site, the subnet mask of 255.255.0.0 is used. This subnet mask specifies that the
second byte of the IP address is used to identify up to 254 subnets. Using this designation, each device
is uniquely identified on its own subnet, but company ABC...

Resolve communication problems with the network
Check the following items to verify the MFP is communicating with the network. This information
assumes a Network configuration page has already been printed. See 
Networking page (HP Color
LaserJet CM1017 MFP only).
1.Are the network cables connected properly?
Ensure that the MFP is attached to the network using the appropriate port and cable. Verify each
cable connection to make sure it is secure and in the right place. If the problem continues, try a...

If yes, the problem is workstation-specific. Verify that both workstations are using the same network
settings.
CAUTIONDo not assign identical TCP/IP addresses to two network devices on the same
network.
5. If network communication is not resolved by using steps 1 through 3, or if other users can not print,
reset all network configuration settings to factory-defaults by selecting  Restore defaults from the
control panel. After the MFP automatically power cycles, wait four to six minutes and verify that...

110 Chapter 11   Network Setup and Administration (HP Color LaserJet CM1017 MFP) ENWW
 

12 How do I?
Use this section to perform basic tasks with the HP Color LaserJet CM1015/CM1017 MFP Series.
●
Control panel and other settings: How do I?
●
Control-panel menus
●
Print: How do I?
●
Copy and Scan: How do I?
●
Photo: How do I? (HP Color LaserJet CM1017 MFP only)
●
Network: How do I? (HP Color LaserJet CM1017 MFP only)
●
Maintenance: How do I?
ENWW111
 

Control panel and other settings: How do I?
This section discusses control-panel settings.
HP Color LaserJet CM1017 MFP control panel features
The HP Color LaserJet CM1017 MFP contains the following lights and buttons on the control panel:
NOTEPrint a demo page by pressing the  Scan To and Start Scan  buttons simultaneously.
1Graphical display. Message, menus, and supply gauge area.
Supplies gauges: Displays consumption levels of  print cartridges. Appears when the MFP shows the Ready
state with no...

2Amber activity light: An error has occurred. Printer requires attention.
3Up arrow (^): Press to enter the main menu system or navigate to the previous menu item, or previous item
in the selection list.
4Cancel (X): Whenever the Ready light blinks, press to cancel a print job. Pressing this button also exits the
control-panel menus.
5Right arrow (>): Press to navigate to the next submenu or the next value in the menu selection list. Also
allows cursor movement forward a single position, or increments a...

After 60 minutes of inactivity, the color graphics display goes into Sleep State and the screen shuts off
completely. The display turns back on when you perform an operation, such as pressing a control panel
button, or inserting a memory card, accessing the HP All-in-One from a connected computer.
Use the control-panel arrows to navigate on the HP Color LaserJet CM1017 MFP
●Press the Up arrow or Down arrow to navigate through all control panel menus.
●Press Back to return to the previous menu.
●Press OK...

Control-panel menus
Use the control-panel menus
To gain access to the control-panel menus, use the following steps.
1.Press Menu.
2.On the HP Color LaserJet CM1015 MFP, press Left arrow or Right arrow to navigate the listings.
On the HP Color LaserJet CM1017 MFP, press Up arrow or Down arrow to navigate the listings.
●Press OK to select the appropriate option.
●Press Cancel to cancel an action or return to the Ready state.
●Press Back to move to the previous menu.
Control-panel menu map
These menus are...

Menu itemSub-menu itemSub-menu itemDescription
 Contrast Increases or decreases the
differences between whites
and blacks of a copy.
 Lightness Increases or decreases the
background color in a copy.
 Grayness Increases or decreases the
color in the color copy of a
black and white original.
 Sharpen Increases or decreases the
reproduction details in a copy.
 Restrict color Permits the enabling or
disabling of color copies.
Restore defaults    Sets all customized copy
settings to the factory default...