HP Color LaserJet 2700 User Manual

							
Repacking the printer
If your printer needs to be moved or shipped to another location, perform the following procedure to
repack the printer.
CAUTION Shipping damage as a result of inadequate  packing is the customers responsibility.
The printer must remain upright during shipment.
To repack the printer
CAUTION It is extremely important  to remove the print cartridges before shipping the printer.
Print cartridges left  in the printer during shipping will leak and entirely cover the printer engine
and other parts with toner.
To prevent damage to the print cartridge, avoid  touching the roller, and store the print cartridge
in its original packing material or so  that it is not exposed to light.
1.Remove all four print cartridges and ship separately.
2. Remove optional tray 3 and ship the tray separately.
3. Use the original shipping container and packing ma terial, if possible. If you have already disposed
of the printer packing material,  contact a local mailing service for information about repacking the
printer. HP recommends insuring the equipment for shipment.
ENWW Repacking the printer 141
 
						

							142 Appendix B   Service and support ENWW
 
						

							C Printer specifications
The printer specifications provide information about the size and weight, amount of power needed and
used, and noise output of the printer. The specifications also describe how the different operating modes
affect power consumption, heat output, and noise output.
Physical specifications
ProductHeightDepthWidthWeight1
Base model
400 mm
(15.7 inches)450 mm
(17.7 inches)400 mm
(15.7 inches)
20.3 kg (44.8 lb)
Base model plus optional tray 3540 mm
(21.3 inches)450 mm
(17.7 inches)400 mm
(15.7 inches)25.4 kg (56.0 lb)
1The printer weight does not include print cartridges.
ENWWPhysical specifications 143
 
						

							
Electrical specifications
WARNING!Power requirements are based on the country/region where the printer is sold. Do
not convert operating voltages.  This may damage the printer and void the product warranty.
Item110-volt models220-volt models
Power requirements100 to 127 V (+/-10%)
50 to 60 Hz (+/-2 Hz)220 to 240 V (+/-10%)
50 to 60 Hz (+/-2 Hz)
Minimum recommended circuit capacity 6.5 A 3.5 A
144 Appendix C   Printer specifications ENWW
 
						

							
Power-consumption specifications
Table C-1  Power consumption (average, in watts)1
Product ModelPrinting2Ready3Sleep4OffHeat output-
Ready (BTU/
hour)
5
HP Color LaserJet 270038545400.5100
HP Color LaserJet 2700n38545400.5100
1The power consumption reflects the hi ghest values measured for color and monochrome printing when using standard
voltages.
2The printing speed is 15 ppm for letter-size media and 20 ppm for A4-size media.3The default activation time from r eady mode to sleep mode is 30 minutes.4The recovery time from sleep mode to the start of printing is 6 seconds.5Maximum heat dissipation for all model s in ready mode is 171 BTU per hour.
NOTEThese values are subject to change.
ENWW Power-consumption specifications 145
 
						

							Acoustic emissions
Sound power levelDeclared per ISO 9296
Printing (15 ppm)1LWAd = 6.9 Bels (A) [69 dB (A)]
ReadyLWAd = 5.3 Bels (A) [53 dB (A)]
Sound pressure level: bystander positionDeclared per ISO 9296
Printing (15 ppm)1LpAm = 55 dB (A)
ReadyLpAm = 39 dB (A)
1The color printing speed is 15 ppm for letter-size media and A4-size media. The monochrome printing speed is 20 ppm for
letter-size media and 20 ppm for A4-size media.
NOTEThese values are subject to change.
146 Appendix C   Printer specifications ENWW
 
						

							Operating-environment specifications
EnvironmentRecommendedAllowed
Temperature17° to 25°C (62.6° to 77°F)10° to 27°C (50° to 81 F)
Humidity20% to 60% relative humidity (RH)10% to 70% RH
Altitude Not applicable 0 to 2600 m (0 to 8530 ft)
NOTEThese values are subject to change.
ENWW Operating-environment specifications 147
 
						

							148 Appendix C   Printer specifications ENWW
 
						

							D Regulatory information
This section contains the following regulatory information:
●
FCC regulations
●
Environmental product stewardship program
●
Declaration of conformity
●
Safety statements
●
Laser statement for Finland
ENWW149
 
						

							FCC regulations
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If this equipment is not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase separation between equipment and receiver.
●Connect equipment to an outlet on a circuit different from that to which the receiver is located.
●Consult your dealer or an experienced radio/TV technician.
NOTEAny changes or modifications to the printer that are not expressly approved by HP could
void the user’s authority to operate this equipment.
Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC
rules.
150 Appendix D   Regulatory information ENWW