HP C4280 User Manual

Solution:Turn the HP All-in-One off, remove any objects that are blocking the print
carriage (including any packing materials), and then turn the HP All-in-One on again.
Cause: The HP All-in-One is out of paper.
Solution: Load paper in the input tray.
For more information, see:
“
Load full-size paper” on page 21
The pages in my document came out in the wrong order
Cause: The print settings are set to print the first page of your document first.
Because of the way the paper feeds through the HP...

Solution:Remove the stack of paper from the input tray, reload the paper, and then
slide the paper width guide inward until it stops at the edge of the paper.
For more information, see:
“
Load paper” on page 21
Cause: A stack of envelopes is loaded incorrectly.
Solution: Remove all paper from the input tray. Load a stack of envelopes in the
input tray, with the envelope flaps facing up and on the left.
NOTE: To avoid paper jams, tuck the flaps inside the envelopes.
For more information, see:
“
Load...

Solution:Make sure the layout of the document you are trying to print fits on a paper
size supported by the HP All-in-One.
To preview the print layout
1. Load the correct paper size into the input tray.
2. Preview your print job before sending it to the HP All-in-One.
3. Check the graphics in the document to make  sure that the current size fits within
the printable area of the HP All-in-One.
4. Cancel the print job if the graphics do not fit in the printable area of the page.
TIP: Some software...

Solution:If the HP All-in-One has only a few sheets remaining, load more paper in
the input tray. If there is plenty of paper in  the input tray, remove the paper, tap the
stack of paper against a flat surface, and reload the paper into the input tray.
For more information, see:
“
Load full-size paper” on page 21
Cause: The protective plastic tape was only partially removed from the print
cartridge.
Solution: Check each print cartridge. The tape might have been removed from the
copper-colored contacts,...

Memory card troubleshooting
Use this section to solve these memory card problems:
•
My memory card no longer works in my digital camera
•
The HP All-in-One does not read the memory card
•
The Photo light next to the memory card slots is blinking
•
The photos on the memory card do not transfer to my computer
My memory card no longer works in my digital camera Cause: You formatted the card on a Windows XP computer. By default, Windows
XP will format a memory card of 8 MB or less and 64 MB or more with the...

Solution:Check the computer screen for an error message telling you that the
images on the memory card are corrupted.
If the file system on the card  is corrupt, reformat the memory card in your digital
camera.
CAUTION: Reformatting the memory card will delete any photos stored on the
card. If you have previously transferred the photos from your memory card to a
computer, try printing the photos from the computer. Otherwise, you will need to
retake any photos you might have lost.
The Photo light next to...

Solution:Turn the HP All-in-One on.
Cause:The computer is turned off.
Solution: Turn the computer on.
Cause:The HP All-in-One is not properly connected to the computer.
Solution: Check the connection from the HP All-in-One to your computer. Verify
that the USB cable is securely plugged into the USB port on the back of the HP All-
in-One. Make sure the other end of the USB cable is plugged into a USB port on your
computer. After the cable is connected properly, turn the HP All-in-One off and then
on...

the HP All-in-One and plugged into a power outlet. Press the On button to turn on the
HP All-in-One.
Cause: The original is placed incorrectly on the glass.
Solution: Load the original print side down on the right front corner of the glass as
shown below.
Cause: The HP All-in-One might be busy copying or printing.
Solution: Check the On button. If it is blinking, the HP All-in-One is busy.
Cause: The HP All-in-One does not recognize the paper type.
Solution: Do not use the HP All-in-One to copy onto...

Solution:Load the original print side down on the right front corner of the glass as
shown below.
Resize to Fit is not working as expected
Cause: You are trying to increase the size of an original that is too small.
Solution: Resize to Fit  can only enlarge the original up to the maximum percentage
allowed by your model. For example, 200% might be the maximum enlargement
percentage allowed by your model. Enlarging a passport photo by 200% might not
enlarge it enough for it to fit a full-size page.
If...

Solution:Load the original print side down on the right front corner of the glass as
shown below. To copy a photo, position the photo on the glass so that the long edge
of the photo is along the front edge of the glass.
Cause: Debris might be stuck on the glass or on the back of the document lid. The
HP All-in-One interprets anything it detects on the glass as part of the image.
Solution: Turn off the HP All-in-One, unplug the power cord, and then use a soft
cloth to wipe the glass and the back of the...