GTE Omni Si Database Technical Practices Issue 1 Manual

TL-130100-1001
STEP
OPERATIONRESULT
4
Non-priority calls are placed in
call-waiting queue.5From any station, access code for
priority call is dialed.
6Terminate call in progress.
7Depress flashing LOOP LED
pushbutton (l-4).
8Depress POS RLSE pushbutton.(e) Trunk and station identification cleared
from variable display.
(f) Class-of-service digits cleared if
present.
(g) TOD displayed.
CALL WTG LED on when level 1 is
exceeded. LED flashes if level 2 is
exceeded.
(a) Ringing heard at 60 IPM.
(b) CALL WTG...

TL-130100-1001STEPOPERATIONRESULT(c) When call-waiting queue reaches
second level, CALL WTG LED flashes
and overflow service is alerted
(if equipped).
2Answer calls.(a) Calls answered in order received
(except for priority calls which move
to top of queue).
(b) When CALL WTG queue is reduced
below second level, LED goes on and
UNA (if programmed) is canceled.
(c) When CALL 
WIG queue is reduced
below level 
1, LED goes off.
4.40Faulty Line
4.40.1Maintenance Print-out Operation
STEPOPERATIONRESULT...

_ :-TL-130100-1001
4.40.2Invalid Operation
STEPOPERATIONRESULT
1Attendant called from one of station
lines.
2Depress flashing LOOP LEDpushbutton (l-4).
3Depress START/STOP pushbutton.
4Depress BAD LINE pushbutton.
5Depress POS RLSE pushbutton.(a) Ringing heard.
(b) LOOP LED flashes at 30 IPM.
(a) LOOP LED on.(b) “INFORMATION” appears in fixed
display field.(c) Line number appears in variable
display field.
(d) POS RLSE LED on.
(e) Ringing stops.(f) Transmission established between
line and attendant.
(a)...

-TL-130100-1001
4.41.2
No Dial Alarm Directed to Attendant
STEPOPERATIONRESULT
1Station assigned no dial alarm feature
(data base option).
2Assigned station left off-hook without(a) After time out period, ringing heard.
dialing.(b) LOOP LED (l-4) flashes at 60 IPM.
3Depress the flashing LOOP LEDpushbutton (l-4).(a) LOOP LED on steady.(b) “NO DIAL ALARM” displays in fixed
display field.
(c) POS RLSE LED on.
(d) START/STOP LED on.
(e) Ringing stops.(f) Transmission established between
off-hook station and...

TL-130100-1001
STEP
OPERATIONRESULT
(e) Attendant Console available for self-test diagnostics, internal program
access.
4.43
Data Link Recovery Attempts
STEP
OPERATIONRESULT
1Attendant Console called from
station.
2Depress the flashing LOOP LED
pushbutton.
3
4
5Depress NITE ANSW pushbutton. Power to Attendant Console turned(a) All lit 
LEDs off.
OFF.(b) Transmission interrupted to station.
Power to the Attendant Console
turned ON.(a) Requests to be initialized.
(b) Verify all queued up messages
dropped...

TL-130100-1001NOTE:A call placed to the Attendant Console can ring and flash the LOOP LED even
though Attendant Console is in night answer mode.
4.44Attendant Console Internal Program Access
Refer to Section TL-130200-1001 for procedures.
4.45Initialization and De-Initialization of Attendant Console via
Request
STEPOPERATIONRESULT
1Place Attendant Console in service
via maintenance.
5
Insert headset.
Remove headset.
Place Attendant Console out of
service via maintenance request.
Return to Step 1 to bring...

TL-130100-1001
STEPOPERATIONRESULT4Repeat Step 2 while performing otherDepressing SPARE pushbutton should not
tests.influence the instrument or switch.
NOTE:
Data Base programmable.
4.47Attendant Handling of Locked Loop Trunk-to-Trunk Calls
STEPOPERATIONRESULT
1
2
34
5
6
5210Incoming CO trunk call with no
disconnect supervision placed to
appropriate number.(a) Ringing heard.
(b) LOOP LED (l-4) flashes at 120 IPM.
Depress the flashing LOOP LED
pushbutton (l-4).
Dial trunk group access code for
outgoing...

TL-130100-1001
NOTE:After a period of time, perform trunk busy verification and Break-In on either trunk.
If trunks are not busy (reorder tone, quiet, etc.), perform a Forced Trunk Release on
either trunk to break connection.
4.48Busy Lamp Display Unit Access
STEPOPERATIONRESULT1
2NOTES:
1.
2.Depress BLDU pushbutton.Enter Hundreds Group number displayed in
fixed display field.
Enter a 2-digit Hundreds Group
number (00-99).(a) Number entered displayed in fixed
display field.
(b) If BLDU attached, status...

TL-130100-1001OPERATIONRESULT
3Station calls Attendant Console.(a) Ringback tone is heard.
(b) Chime is heard.
(c) LOOP LED flashes at 30 IPM.
5210
8187O-225 

TL-130100-1001THIS PAGE INTENTIONALLY LEFT BLANK.O-226
8l875210