GTE Omni Si Database Technical Practices Issue 1 Manual

TL-130100-1001
STEP
NOTE:OPERATIONRESULT
If called party does not answer within reasonable time, release call as described in
Step 5.5Depress POS RLSE pushbutton to
release call.(a) Fixed display clears.
(b) PAGE, LOOP, and POS RLSE 
LEDs off.
(c) TOD displayed.
4.21.2Code Calling With Outside Party Waiting
STEP
OPERATIONRESULT
1
2
3
4NOTE:
5
6Inform outside caller of intent to page
inside party.
Dial the following:
(a) Code call access code.
(b) Zone-paging digit (if applicable).
(c) One-, two-, or...

TL-130100-10014.22
Attendant Trunk Group Restriction
STEPOPERATlONRESULT
1Depress an idle LOOP pushbutton
(l-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) STOP/START LED on.
(d) Dial tone heard.
2Dial activation access code followed(a) Restriction LED of trunk group indicates
by number of trunk group to bein trunk group-status display of the
restricted.
BLDU.
(b) 
60-IPM tone heard.
(c) Dialed digits appear on fixed display.
(d) START/STOP LED off.
NOTE:Restriction is removed by attendant dialing a...

TL-130100-1001
STEPOPERATION
RESULT4Repeat Steps 1 through 3 for all
trunks in use.Results are same as in Steps 1 through 3.
NOTE:
If the trunk does not have answer supervision and if an MDR call record is desired,
the attendant must depress the START/STOP key after all digits have been dialed.
4.23.2
Attendant Control of Facility (ACOF)
STEP
OPERATION
RESULT
1
2
3
4
5
6
7
85210Depress an idle LOOP pushbutton
(l-4).
Dial the trunk group block on access
code and the trunk group number (00
through 63) to...

TL-130100-1001
STEPOPERATIONRESULT
9Unblock additional trunk groups by
repeating Steps 6 through 8.Results are same as Steps 6 through 8.
10Originate station call to a trunk inStation call completed.trunk group taken off block in Step 7.
4.24Trunk Busy Verification and Break-in
STEPOPERATIONRESULT
1Depress idle LOOP pushbutton (1-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) Dial tone heard.
(d) START/STOP LED on.
(e) Fixed display cleared.
2
3Dial trunk-busy verification code.Dialed digits appear on...

--:TL-130100-1001
STEP
OPERATIONRESULT
(c) TOD displayed.
(d) 
1204PM busy tone ceases.
NOTE:
If trunk is engaged in three-way conversation, or if a data-line secure station is
involved, the BRK IN LED does not go on after flashing, and a BREAK-IN DENIED
message is displayed. If LED trunk is maintenance busy or out of service, BRK IN
LED flashes at 
j20 IPM, a 1204PM busy tone is received at the Attendant Console,
and a BREAK-IN DENIED message is displayed.
4.25
Forced Trunk ReleaseSTEP
OPERATIONRESULT...

TL-130100-I 001
STEPOPERATIONRESULT
(f) Class-of-service digits cleared if
present.
(g) TOD displayed (see Table 4.1 for time
code conversion).
4.26
Dynamic FRL Table4.26.1Table Update
STEP
OPERATIONRESULT
1Depress idle LOOP pushbutton
(l-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
Dial appropriate access code
for FRL assignment map update.
Dial the new FRL table values.(a) Dial tone ceases.
(b) Fixed display contains dialed digits.
(a) Dialed digits appear on the...

TL-130100-1001STEPOPERATIONRESULT(c) START/STOP LED on.
(d) Dial tone heard.
2Dial appropriate access code
for displaying FRL data.(a) Dial tone ceases.
(b) Fixed display contains dialed digits.
(c) When all access code digits are entered,
dialed digits display clears.
(d) Dynamic FRL table appears on variable
display.
3Depress POS RLSE pushbutton.(a) LOOP LED off.
(b) POS RLSE LED off.
(c) Fixed display cleared.
(d) Trunk and station identification cleared
from variable display.
(e) TOD displayed (see...

 r.:---TL-130100-1001
STEPOPERATIONRESULT
5Depress NITE ANSW pushbutton
and key in 1 or 2 on the Attendant
Console that controls night answer
(master console). Place any other
console to night mode.(a) Night Answer message displayed in
fixed display.
(b) Night Answer LED on.
(c) STAFFED LED off. System is now in
night-answer mode associated with
the entered key (see note).
NOTE:Use of UNA and PNA is data base dependent and may be assigned to either Night
Answer 1 or 2.
4.27.2
Flexible Night Connections...

TL-130100-1001/’
STEPOPERATIONRESULT(c) STAFFED LED is off. Every station
classmarked to receive incoming
trunk calls can answer an incoming call
by dialing assigned night-answer
access code.
NOTE:The Nl position may be a combination of both UNA and PNA for the different trunks.
4.27.4Night Answer 1 Verification
STEPOPERATIONRESULT
1Place incoming trunk call to
appropriate number.(a) Ringback heard.
(b) Audible and/or visible night-answer
signal received (as provided by
customer for UNA).
2Dial assigned...

TL-130100-1001
STEPOPERATION
RESULT2Answer call at station.Transmission established between calling
party and station.
3Repeat Steps 1 and 2 for different
trunks until all PNA destination
numbers have been verified.Results are same as Steps 1 and 2.
4.28Group Speed-Calling Update
STEPOPERATIONRESULT
1Depress idle LOOP pushbutton
(l-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
2Dial appropriate access code for
updating group speed-calling data.(a) Dial tone stops....