GTE Omni Si Database Technical Practices Issue 1 Manual

TL-130100-1001NOTE:Speed Calling numbers are grouped by data base in 25 different sublists. The
access to a particular 
sublist can be restricted in data base, by group speed calling
access class (set of sublists) assigned to the line originating a group speed call.
4.29
4.29.1
Timed-Reminder
Timed-Reminder Activation
STEPOPERATIONRESULT
1
2
NOTES:
1.
2.
3.
4.
3Depress idle LOOP pushbutton
(1-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
Dial timed-reminder access...

TL-130100-1001
STEPOPERATION
RESULT.:,
2
3Dial timed-reminder cancel code and
(a) START/STOP LED off.
station number.(b) Dialed digits appear on fixed display.
Depress POS RLSE pushbutton.
(a) LOOP and POS RLSE LEDs off.
(b) Fixed display goes off.
(c) TOD displayed (see Table 4.1 for time
code conversion).
4.30Message WaitingSTEPOPERATIONRESULT
1Depress idle LOOP pushbutton
(l-4).
2
3Depress MESG WTG pushbutton.
Dial station directory number.
Three digit station number must be
preceded by 
# key....

TL-130100-10014.31Most Economical Route Selection (MERS) Active Time Zone
DisplaySTEP
OPERATIONRESULT
1Depress idle LOOP pushbutton
(l-4).
2Dial access code for active MERS
time zone display.
3Dial end-time-display digit (digit I).4Depress POS RLSE pushbutton.(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
(a) Zone number in use displayed 
in-calling number display field.
(b) Dialed digits appear on fixed display.
(a) End time for the active time zone
displayed in...

--TL-130100-1001
STEP
OPERATIONRESULT
4Dial first digit of two-digit hours
of beginning time data.(a) End time, if any, of previously entered
data displayed.
(b) Dialed digit appears on fixed display.
5Dial remaining beginning-time
and end-time data.(a) Confirmation tone heard.
(b) START/STOP LED off.
(c) Dialed digits appear on fixed display.
6Repeat Steps 1 through 5 to verify
that entered data is correct.
7Depress POS RLSE pushbutton.(a) POS RLSE and LOOP LEDs off.(b) Fixed and variable displays...

TL-130100-I 0014.33Call Park
STEPOPERATION
RESULT
1When conversing with outside
party or another station and
outside party wishes to speak to
another party at another station,dial call-park access code.
2Dial directory number of station to
park call.
3Station that call is parked on can
still originate or receive other calls.
4Contact party whose station call is
parked on (this is done by either
paging or telephoning the party ifthat party’s location is known).
5The party on whose station call is
parked...

TL-130100-1001
4.34Attendant Recall
STEP
OPERATION
RESULT1Incoming CO trunk call received at
(a) Ringing heard.
Attendant Console.
(b) LOOP LED (l-4) flashes at 120 
IPM
2Depress flashing LOOP LED
pushbutton.(a) LOOP LED on.
(b) “LOCAL” appears in fixed display field.
(c) Trunk number appears in variable
display field.
3
4
5
6
7
8Dial station number.
Call is answered at the station.
Depress POS RLSE pushbutton.
At the station, the hookswitch is
flashed and at the Attendant
Console all of the LOOP keys...

TL-130100-100110
11STEPOPERATION
RESULT
(e) Available LOOP LED flashes.
(f) Ringing heard.
9Depress flashing LED LOOP
pushbutton.(a) LOOP, POS RLSE and START/STOP
LEDs on.
(b) If station of Step 6 was next in queue,
station number, COS, and TRANSFER
appear on display.
(c) Ringing stops.
(d) Transmission established between
station and Attendant Console, or 
as.adata base option, a three-way
connection established among at-
tendant, station, and trunk.
Provide assistance required.
Depress POS RLSE...

TL-130100-1001STEPOPERATIONRESULT(d) 
Ringback tone heard.
(e) Called station rings.
4Depress POS RLSE pushbutton.(a) Attendant Console released from call.
(b) Trunk receives 
ringback tone.
(c) LOOP LED off.
(d) POS RLSE LED off.
(e) EXCL SRCE or EXCL DEST LED off if
(f) 
Fked display cleared.
(g) Trunk and station identification
cleared from variable display.
(h) Class-of-service digits cleared if
present.
(i) TOD displayed.
5Allow time out (data base) to occur.LOOP LED flashes at 60 IPM.
6Depress...

rTL-130100-1001
STEPOPERATIONRESULT
4Place station on-hook.(a) Variable display cleared.
(b) TOD displayed.
5Depress POS RLSE pushbutton.(a) LOOP and POS RLSE LEDs off.
(b) Fixed and variable display cleared.
(c) TOD displayed.
6Repeat Steps 1’ th;ough 6 for all
stations.
4.37Attendant Call Splitting
STEPOPERATION
RESULT
1
2
3
4
55210Incoming trunk call placed to
appropriate number.
Depress flashing LED LOOP
pushbutton (l-4).
Dial valid three- or four-digit
station number.
Answer call at station.
Depress...

.-TL-130100-1001
STEPOPERATIONRESULT
(d) Transmission established between
trunk and attendant.
6Depress EXCL SRCE pushbutton.(a) EXCL DEST LED off.
(b) EXCL SRCE LED on.
(c) Trunk placed on hold in 
exclude-source state.
(d) Transmission established between
station and attendant.
7Depress EXCL SRCE pushbutton.(a) EXCL SRCE LED off.
(b) Transmission established between
trunk, attendant and station.
8Depress POS RLSE pushbutton.(a) EXCL DEST LED off.
(b) POS RLSE LED off.
(c) LOOP LED off.
(d) Trunk to...