GTE Omni Scbs Installation And Maintenance Manual

FEATURES PACKAGES A AND B DEFAULT PACKAGE C DEFAULT DATA BASE 
DATA BASE ACCESS CODES (FAC) ACCESS CODES (FAC) 
SCC 1 Access 40 40 (Basic) 46 (Expanded) 
1 SCC 2 Access 
I 42 1 42 (Basic) 47 (Expanded) 
I 
I SCC 3 Access 
SCC 4 Access 
Station Speed Calling I 43 I 43 (Basic) 48 IExoanded) I 
44 
*0 + user programmed SPC (O-9) 44 (Basic) 49 (Expanded) 
*O + user programmed SPC (O-9) 
I System Speed Calling 
I ## + installer programmed SPC (00-99) I ## + installer programmed SPC (00-99) I 
I 
Save/Beoeat...

FEATURES 
Station Camp-On Cancel 
PACKAGES A AND B DEFAULT PACKAGE C DEFAULT DATA BASE 
DATA BASE ACCESS CODES (FAC) ACCESS CODES (FAC) 
#* #* 
1 Trunk Camp-On Cancel I #7 I #7 I 
1 G LOUD Pickuo I *4 I *4 I 
Call Park Answer 
Night Answer Pick Up (self-tenant) 
Night Answer Pick Up (all-tenant) #9 + Call Park Orbit No. (l-4 digits) 
#30 
#31 #9 + Call Park Orbit No. (1-4 digits) 
#30 
#31 
Directed Call Pick Up 
DSS Park Answer 
Data Call Attribute Change 
Do Not Disturb Override Activate 
Do Not...

FEATURES PACKAGES A AND B DEFAULT PACKAGE C DEFAULT DATA BASE 
DATA BASE ACCESS CODES (FAC) 
ACCESS CODES IFACI 
I 
Limited Executive Override (overrides only stations 
with higher COR) 
I #5 
I #5 
1 
1 Call Park Activate 
I *9 + 3 digit orbit no. 
I *9 + 3 diait orbit no. I 
Add Data Call Set Up (Package B) 
67 67 
I 
Account Code/Client Billing 56 + identifier (1 to 15 digits) 
56 + identifier (1 to 15 digits) 
I 
I 
Executive Override (extends Limited Override 
I #5 (not in default data base, must...

DESCRIPTION 
Iigit Receive 
Incoming digit receive time cut 
Incoming interdigit time cut PACKAGES AI0 PACKAGE C 
DEFAULT VALUE DEFAULT VALUE 
IN SECONDS IN SECONDS 
(* 0.2) (* 0.2) 
11.26 11.26 
7.17 7.17 CMC 
TABLE 
254 
254 
Digit Send 
Pm-pause timing (manual) 
Interdigit timing (10 pps) 
lnterdigit timing (20 pps) 
Pre-pause timing (speed call) 
Interdigit pause (speed call) 
Interdigit timing (DTMF) 
jystem Timing 
Station hook signal (maximum 
before disconnect 
Call start time after sending all...

_-_ 
efault Stander 
iz 
DIALING DESTINATION 
Local/Toll Operator 
International Operator 
Toll Prefix 
International Prefix 
Special Number 
Office Code 
DIALING PATTERN 
0 
01 
1 
011 
N-II 
NNX 
Area Code NO/IX 
Station Number x to xxxx 
NOTES: 
1. X=Oto9, N=2to9 
2. Type of call available: 
NNX + XXXX 
I+ NNX + XXXX 
NO/IX + NNX + XXXX 
I+ NO/IX + NNX + XXXX 
0 + (time out) 
0 + NNX + XXXX 
0 + NO/IX + NNX + XXXX 
Nil 
01-l+ 12X’s 
2.32  

Guide to Data ase Programming at Time 
f System Imst 
OPERATIONAL 
VERIFICATION 
f 
PROGRAM PROGRAM PROGRAM 
BASIC TRUNK 
TERMINATIONS APPLICABLE + PROGRAM APPLICABLE 
DATA SERVICE cos 
FUNCTIONS 
PROGRAM 
PROGRAM TRUNK 
PROGRAM 
TERMINATIONS OR KEY - TRUNK DIALING 
SMDR MULTI-DIGIT + 
SYSTEMFEATURES 
DATA 
RESTRICTION. 
ANWOR LCR 
SAVE 0008 TO PERFORM 
TAPE OR FLOPPY - oPERAT’oNAL 
VERIFICATION COMPLETION 
OKXETTE 
PROCEO”RES 
PROGRAM SBCS 
BEHIND A PABX, PROGRAM 
TENANT ASSIGNMENT, - DATA STATION -...

view Exercise - 
Data Base 
INSTRUCTIONS: THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, TRUE/FALSE, FILL IN THE BLANK, OR 
MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E. STUDENT WORKBOOK, NOTES, AND GTEP MANUAL) MAY 
BE USED AS REFERENCES. SUBMIT EXERCISE TO INSTRUCTOR FOR GRADING WHEN LAST QUESTION HAS BEEN 
COMPLETED. 
1. THE OMNI SBCS OPERATING SYSTEM SOFTWARE AND DEFAULT DATA BASE RESIDE ON BOTH THE AND 
CARDS. 
2. PROGRAM CHANGES CAN BE MADE WITH THE OR INSTRUMENTS. 
3. SPECIAL...

Review Exercise 
- Data Base 
Overview 
(2.1) (Continued) 
11. 
12. 
13. 
14. 
15. 
16. 
17. 
16. 
19. 
20. WHAT IS DISPLAYED ON THE PMP SCREEN IF THE SECURITY CODE IS NOT ACCEPTED BY 
THE SYSTEM? 
. 
THE 
PROCEDURE LOADS AND ESTABLISHES THE SYSTEM DEFAULT 
STANDARD DATA BASE. 
THE PORTABLE MAINTENANCE PANEL IS USED PRIMARILY: 
A. AS AN INSTRUCTIONAL DEVICE TO TEACH CUSTOMERS ABOUT OMNI SBCS 
FEATURES. 
B. FOR PERFORMING ROUTINE MAINTENANCE, CREATING OR MODIFYING THE 
OMNI SBCS DATA BASE, AND ISOLATING...

,_.--. 
21. 
22. WHAT SCREEN IS DISPLAYED WHEN THE PMP IS IN “COMMAND MODE”? 
WHAT IS THE PROCEDURE FOR OBTAINING A HARD COPY OF A CMC COMMAND WITH 
CURRENT PARAMETER STATUS? 
23. (TRUE OR FALSE) 
THE PMP CANNOT COMMUNICATE WITH THE OMNI SBS 
IF THE MEM AND SWC CARDS HAVE NOT BEEN SEATED. 
24. OMNI SBCS DATA BASE TABLES ARE ADDRESSED BY A THREE-DIGIT: 
. 
25. 
THE OMNI SBCS DEFAULT STANDARD STATION DIRECTORY NUMBERING PLANS BEGINS 
WITH DIRECTORY NUMBER 
AND ENDS WITH 
. 
2.36  

Student Notes 
2.37