GTE Omni Scbs Installation And Maintenance Manual

,. :r .,,, 
,,‘. I.~. 
/: )  ,; -x1 
T 
ADMINI 
TIO 
Pr 
a 
an 
LF/DSS 
2.38  

2.2 Enabling Objective 
GIVEN: 
ACTION: l GTE OMNI SBCS 
. GTE OMNI SBCS PERIPHERALS 
. PORTABLE MAINTENANCE PANEL 
. GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE 
. LABORATORY ACTIVITY - PROGRAMMING STATION INSTRUMENTS AND 
BLF/DSS MODULES. 
. REVIEW EXERCISE 
. USE OMNI SBCS PROGRAMMING TOOLS AND EQUIPMENT TO: 
- 
INSTALL AND REMOVE EKT INSTRUMENTS, SLT INSTRUMENTS, AND 
BLF/DSS MODULES. 
- ASSIGN AND MODIFY EKT, BLF/DSS BUTTON ASSIGNMENTS. 
. COMPLETE REVIEW EXERCISE. 
CRITERIA: 
....

,_. r-. 
; I 
/:’ ‘;, 
 
Default Standard EKT 
Button Assignment/CS-10 and CS-20 
GiE OMNU sl3cs 
STANDARD CONFIGURATION (CARD SLOPS 00 OR 02-l 4) 
ALTERNATE CONFIGURATION (CARD SLOT 01) 
6 
2.40  

Default Standard CSD* 
Button Assign 
CSD CONNECTED TO AN 8DTC CARD 
CSD CONNECTED TO 8DTC CARDS 
INSTALLED IN CARD SLOT 01 
INSTALLED IN CARD SLOTS 02-l 4 
~~@kq~p&-I 
lTkpkyA**l 
,--I SPEAKER - 
I-1 MUTE 
I-1 TRANSFER 
1-1 HOLD I SPEAKER 
II MUTE 
-FIXED KEYS 
I-1 TRANSFER 
I-1 HOLD 
CSD EQUIPPED WITH DTA INTERFACE 
INSTALLED IN CARD SLOTS 
00,03,08,09, and 12 
SPEAKER 
II MUTE 
-I- FIXED KEYS 
,--I TRANSFER 
I-1 HOLD 
I 
I 
_-. .-_ * PACKAGE B/PHASE 1.5 AVAMBLITY 
2.41 
-FIXED KEYS  

1 PROCEDURE ) * 
1. COLD RESTART THE SYSTEM (IF AT TIME OF lNlTlAL SYSTEM 
INSTALLATION) OR HOT RESTART THE SYSTEM (IF INSTALLING 
INSTRUMENT AFTER INITIAL SYSTEM INSTALLATION). 
2. REFER TO DEFAULT STANDARD DATA BASE TABLES FOR DEFAULT 
DIRECTORY NUM ER ASSIGNMENT AND B TTON ASSIGNME 
(FOR CS-10, CS-20, OR CSD). 
3. PROGRAM DESIRED DATA BASE CHANGES WWIT 
PPLICABLE CMC 
S USING DEFAULT STANDARD SETTINGS AS BASIS FOR 
THE CUSTOMIZED DATA BASE. 
*ASSUMES LINE CARD HAS BEEN INSTALLED IN ABPPROPRIATE Sk...

ogram 
Station In 
1 PROCEDURE ] * (REFER TO OMNI SBCS GTEP MANUAL, DATA BASE PROGRAMMING SECTION) 
1. 
USE CMC-200 TO ASSIGN: 
. EQUIPMENT NUMBER (Pi) 
. STATION DIRECTORY NUMBER (P2) 
. TYPE OF TERMINAL (P3) 
. COPIED STATION DIRECTORY NUMBER (P4) 
2. USE CMC-201 TO ASSIGN: 
. DIRECTORY NUMBER (Pl) 
. OPERATION MODE (P2) 
. TYPE OF DIALING (P3) 
. TENANT NUMBER (P4) 
. METERING GROUP (P5) 
3. USE CMC-202 TO ASSIGN: 
. STATION DIRECTORY NUMBER (PI) 
. DAY CLASS OF SERVICE (P2) 
. NIGHT CLASS OF SERVICE...

Station Instruments/Manu 
(Continued) 
GTE OMNi SBCS 
4. USE CMC-204 (IF APPLICABLE) TO ASSIGN: 
. STATION DIRECTORY NUMBER (Pl) 
. DATA SECURE PATH (P2) 
. OFF PREMISES EXTENSION (P3) 
. SLT WITH MESSAGE WAITING LAMP (P4)** 
5. USE CMC-203 (ONLY FOR CS-10, CS-20, AND CSD INSTRUMENTS) TO 
ASSIGN FEATURES OR SERVICES TO BUTTONS: 
. STATION DIRECTORY NUMBER (Pl) 
. BUTTON NUMBER (P2) 
@ FEATURE NUMBER (P3) 
. SUPPLEMENTARY DATA (P4) 
. LINE TERMINATION TYPE (P5) 
. RINGING MODE (P6) 
NOTE: IF LINE BUTTON...

dent Notes 
2.45  

Programming Station 
odification- 
tation I formation 
PROCEDURE (CHANGE) 
1. USE CMC-203 TO: 
@ REMOVE UNWANTED EKT BUTTON 
ASSIGNMENTS 
. ENTER NEW BUTTON ASSIGNMENTS 
2. USE CMC-200 TO: 
. CHANGE STATION DIRECTORY 
NUMBERS AND/OR EQUIPMENT 
NUMBERS 
3. CHECK CMC-201, CMC-202 AND 
CMC-204 TO: 
0 MAKE ANY CHANGES AFFECTED BY 
DIRECTORY NUMBER CHANGE 
(COS/COR OPERATION MODE TYPE 
OF DIALING, TENANT NUMBER, 
METERING GROUP, DATA SECURITY 
OR OPX DESIGNATION. 
4. CHECK CMC-306 AND CMC-307 TO: 
. MAKE ANY...

Programming Station Instruments/ 
C Corn and Summary 
CATEGORY 
CMC TABLE FUNCTION 
. STATION DN 
200 ASSIGNS, REMOVES, OR CHANGES 
ASSIGNMENT DIRECTORY NUMBER AND TYPE OF 
TERMINAL. 
. STATION DATA 
ASSIGNMENT 
. STATION COS/COR 
ASSIGNMENT 
l EKT BUTTON 
ASSIGNMENT 
. DATA SECURITY 
AND OPX 201 
202 
203 
204 ASSIGNS, REMOVES, OR CHANGES A 
STATION’S OPERATION MODE, TYPE 
OF DIALING, TENANT NUMBER, OR 
METERING GROUP NUMBER. 
ASSIGNS, REMOVES, OR CHANGES A 
STATION’S CLASS OF SERVICE OR 
CLASS OF...