GTE Omni Scbs Installation And Maintenance Manual

. 
1 = CO - BOTHWAY CO TRUNK 
2 = BW -.BOTHWAY TERMINATION 
3 = NUMBERS REFER TO DATA BASE 
PARAMETERS ENTRIES.  ALL CO TRUNK LINES ARE PLACED IN TRUNK GROUP 13. TRUNK GROUPS MAY BE DIAL ACCESSED VIA FEATURE ACCESS CODES (FEATURE NUMBERS 4-27). 
TRUNK INSTALLATION ASSUMES DEFAULT STANDARD DATA BASE ASSIGNMENTS FOR TYPE OF TRUNK CARD (4BWC, PTTE, OR 2TTU BEING INSTALLED. 
DEFAULT TRUNK ASSIGNMENT DATA:...

1 PROCEDURE ]* (REFER KO 0 
ANUAL, DA-I-A 
SECTION) 
-I. C-250 TO ASSIGN/ADD I-RUN 
@ TRUNK EQUIPMENT NUMBER (PI) 
@ TYI’E OF TRUNK (P2) 
@ TRUNK GROUP NUMBER (Ip3) 
@ O~~RA~~~~ MODE (P4) 
@ SPGNALING ( 
@ ZONENU 
2. 
C-251 TO Asss 
CIA-I-ED W-i- 
STALLED T 
NT NUMBER (PI) 
@ 
SE OR DTMF (B 
RECTORY NUM 
= TENANT NUMBER (0 TBONAL) (WI) 
3. USE CMC-306 (SF APPblCABLE) TO ASSIGN TRUNK FOR NlGHT RBNG 
DESTINATION. 
CMC=250 
Pi: 182 84: 3 
P2: 6 P5: 2 
P3: 14 P6: 1 
CMC = 251 
PI: 182 P4: 2 
P2: 5 
P3: 182...

1 PROCEDURE I* 
(REFER TO OMNI SBCS GTEP MANUAL, DATA BASE PROGRAMMING 
SECTION) 
1. 
2. 
3. 
4. USE CMC-250 TO REMOVE TRUNK FROM ASSIGNED GROUP.* THIS OPERATION 
ALSO AFFECTS OTHER CMC TABLES BY: 
@ AUTOMATICALLY REMOVING TRUNK DATA ASSIGNMENTS FROM CMC-251. 
AND 
o AUTOMATICALLY REMOVES TRUNK FROM THE TERMINATING TRUNK GROUP. 
USE CMC-307 (IF APPLICABLE) TO REMOVE TRUNK FROM DIRECT IN-LINE 
ASSIGNMENT. 
USE CMC-306 (IF APPLICABLE) TO REMOVE TRUNK FROM NIGHT RINGING 
DESTINATION ASSIGNMENT. 
ASSIGN...

ALLOWS STATlON USER TO PLACE OUTGOING CALLS VIA CO LINE TO ACCESS SCC 
NETWORK (SPRINT, MCI, ETC.). SBCS SYSTEM AUTOMATICALLY SEIZES CO TRUNK, 
OUTPUTS DIRECTORY NUMBER OF DESIGNATED SCC SWITCH TO CO AND 
OUTPUTS REQUIRED SECURITY CODE AND DESTINATIION DIRECTORY NUMBER TO 
SCC SWITCH. 
I PROCEDURE] * (REFER TO OMNI SBCS GTEP MANUAL, DATA BASE 
PROGRAMMING SECTION) 
I. USE CMC-404 TO ASSIGN: 
@ SC@ ROUTE NUMBER (WHICH CORRESPONDS 
CMC=404 
Pl: 2 P4: 0200 
TO DESIGNATED TRUNK GROUP NUMBER) (P-l) P2:...

,- . 
ming sic Trunk Data/ 
CATEGORY FUNCTION 
e TRUNK GROUP ASSIGNMENT 
@ TERMINATING TRUNK 
GROUP ASSIGNMENT 
@ TRUNK DATA ASSIGNMENT 
. NIGHT ANSWER ASSIGNMENT 
. DIRECT-IN LINE ASSIGNMENT 
0 SPECIALIZED COMMON 
CARRIER (SCC) ASSIGNMENT 
250 
253 
251 
306 
307 
404 ASSIGN TRUNK,ClRCUlTS TO TRUNK 
GROUPS. 
ASSIGN TRUNKS TO TERMINATING 
TRUNK GROUP MEMBERS. 
ASSIGNS A DIRECTORY NUMBER TO A 
TRUNK, ASSIGN TO TENANT, SET TRUNK 
PARAMETERS IF NECESSARY. 
ASSIGN TRUNKS TO NIGHT ANSWER 
GROUP. 
ASSIGNS A...

2.73  

PERFORM THE FOLLOWING PROGRAMMING TASKS IN THE SEQUENCE OUTLINED BELOW USING THE SAMPLE WORK 
ORDERS AND IN ACCORDANCE WITH THE GTE OMNI SBCS GTEP MANUAL. COMPLETE THE REVIEW EXERCISE 
QUESTIONS PERTAINING TO THE BASIC TRUNK PROGRAMMING UPON COMPLETION OF THIS LABORATORY ACTIVITY. 
WORK ORDER #2.3 
ZOMPANY NAME: NU SYSTEM CO. 
-0CATION: RESTON, VIRGINIA 
IRIGINATOR: TELECOMMUNICATIONS MANAGER PHONE #: (703) 555-1212 WORK ORDER H2.3 (TASK #l) 
‘ASKS: 
l Add, modify, or remove a trunk with CMC-250. 
e...

WORK ORDER #2.3 
:OMPANY NAME: 
NU SYSTEM CO. 
.OCATION: RESTON, VtRGlNlA 
)RIGINATOR: TEbECOMMUNlCATlONS MANAGER PHONE #: (703) 555-1212 
WORK ORDER #2.3 (TASK #2) 
-ASKS: 
e 
Restore E & M tie line assignment with CMC-250. 
Q 
Assign diaf mode and break ratio with CMC-251. 
e 
Assign tenant number to trunks with CIVIC-251. 
(1) Return the E & M tie line to slot 17 circuit 0. 
(2) Change the dial mode for trunks at slot 18, 
circuits 0 and 1 to DTMF. 
(3) Assign the CO trunk at slot 18, circuit 1 to...

_. . . 
WORK ORDER #2.3 
:OMPANY NAME: NU SYSTEM CO. 
OCATION: RESTON, VIRGINIA 
1RIGINATOR: TELECOMMUNICATIONS MANAGER PHONE #: (703) 555-1212 
WORK ORDER #2.4 (TASK #5) 
ASKS: 
. Establish and assign an SCC trunk with CMC-404 and CMC-405. 
l Restore default tenant group status with CMC-251. l Restore CO trunk with CMC-250. 
‘ARAMETERS: INSTRUCTIONS: 
(1) Assign an SCC trunk with CMC-404 using the 
(1) 
following parameters: Perform basic trunk programming changes. 
Route Number = 1 (2) Check/test the...

INSTRUCTIONS: THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, TRUE/FALSE, FILL IN THE BLANK, OR 
MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E. STUDENT WORKBOOK, NOTES, AND GTEP MANUAL) MAY 
BE USED AS REFERENCES. SUBMIT EXERCISE TO INSTRUCTOR FOR GRADING WHEN LAST QUESTION HAS BEEN 
COMPLETED. 
1. IDENTIFY THE EQUIPMENT NUMBERS FOR EACH TRUNK WHEN IT WAS INITIALLY INSTALLED: 
co 
co 
co 
CO (MUSIC SOURCE) 
TIE (LOOP) 
TIE (LOOP) 
TIE (E&M) 
TIE (E&M) 
2. SELECT THE DEFAULT STANDARD OPERATION...