GTE Omni Scbs Installation And Maintenance Manual

Programming Basic 
ai!mw sLm3 
4. SELECT THE TYPES OF SlGNALlNG WHlCH ARE AVAILABLE WHEN ADDING TRUNKS: 
A. WINK, DELAY, OR IMMEDIATE 
B. E&M OR INCOMING 
C. DIAL PULSE OR DTMF 
D. GROUND OR LOOP 
5. IDENTIFY THE DEFAULT STANDARD TRUNK GROUP NUMBERS FOR THE FOLLOWING TRUNKS: 
co 
E&M TIE 
LOOP START TIE 
6. WHAT ARE THE REQUIRED PARAMETERS WHEN ADDING A WATS TRUNK LINE WITH 
CMC-250? 
7. WHY WOULD A “NOT RGTR” MESSAGE BE DISPLAYED WHEN ADDING TRUNK EQUIPMENT 
NUMBER 184 IN THE LAB? 
2.78  

eview Exercise 
2 3)  0 
GE OMNI SEES 
8. WHAT ERROR MESSAGE WILL BE DISPLAYED IF A LOOP TIE TRUNK IS ADDED AT CMC-250 
WITH A VALUE OF 1 ENTERED FOR PARAMETER 5? 
9. CIRCUITS ON THE 
CARD ARE ASSIGNED TO TRUNK GROUP NUMBER 1 BY 
DEFAULT. 
IO. WHAT ARE THE ADVANTAGES OF CHANGING A TRUNK’S DIAL MODE TO DTMF? 
11. THE OMNI SBCS WILL ALLOW 
TENANT TRUNK GROUPS. 
12. WHAT OCCURS WHEN A STATION FROM A DIFFERENT TENANT GROUP TRIES TO ACCESS A 
TRUNK THAT IS NOT IN THEIR TENANT GROUP? 
13. IN THE LAB, ATTEMPT...

, 
Review Exercise 
- Programming Basic 
15. WHAT IS THE DEFAULT FEATURE ACCESS CODE FOR EACH TRUNK ACCESS: 
__ CO#l 
- WATS#l 
- TIE #I (E&M) 
- TIE #2 (LOOP) 
- SCC#l 
16. MATCH EACH OF THE FOLLOWING TERMS WITH ITS CORRECT DEFINITION: 
~ TRUNK FEATURE ACCESS CODES 
___ TRUNK GROUP NUMBER A. USED BY SYSTEM TO ACCESS SCC 
NETWORK 
- SIGNALING 
B. GROUND OR LOOP START 
~ DIAL MODE/BREAK RATIO 
C. ASSIGNMENT IDENTIFYING GROUPS OF 
-TERMINATING TRUNK GROUP NUMBER 
TRUNKS TERMINATING TO STATION 
-TRUNK...

Student Notes 
I 
2.81  

DATA BASE ADMINISTRATION 
Programming Trunk Terminations 
2.82  

GIVEN: @ GTE OMNI SBCS 
. GTE OMNI SBCS PERIPHERALS 
@ PORTABLE MAINTENANCE PANEL 
@ GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE 
@ LABORATORY ACTIVITY - PROGRAMMING TRUNK 
TERMINATIONS 
@ REVIEW EXERCISE 
ACTION: 
CRITERIA: 0 USE OMNI SBCS PROGRAMMING TOOLS AND EQUIPMENT TO: 
- ASSIGN A DIRECT-IN LINE. 
- ASSIGN KEY SYSTEM TRUNK LINE TO EKT STATION. 
- CREATE A PERSONAL/PRIVATE TRUNK LINE. 
- ASSIGN POOLED INCOMING TRUNK LINES. 
- ASSIGN POOLED OUTGOING TRUNK LINES. 
- ASSIGN POOLED BOTHWAY...

Programming Trunk Terminations/ 
werwiew 
DESCRIPTION 1 
. TRUNKS CAN BE TERMINATED TO SINGLE LINE TELEPHONE SETS OR TO BUTTONS ON 
ELECTRONIC KEY TELEPHONE SETS. 
. DEFAULT STANDARD DATA BASE ASSIGNS ALL TRUNK GROUPS TO TRUNK GROUP 13 UPON 
INSTALLATION. 
. TERMINATING TRUNK GROUP (TTGN) ASSIGNMENTS MUST BE SPECIFIED TO TERMINATE 
TRUNKS TO STATION INSTRUMENTS. 
. TYPES OF TRUNK TERMINATIONS: 
DIRECT-IN TRUNK LINE - DIRECT TERMINATION OF CO TRUNK LINE TO SLT OR EKT 
INSTRUMENT, BYPASSING A BLF/DSS...

Programming Trunk Terminations/ 
wiew (C 
POOLED OUTGOING TRUNK - 
ALLOWS OUTGOING TRUNK LINES TO BE POOLED INTO A 
GROUP 
TERMINATING TRUNK GROUP CONNECTED TO MULTIPLE 
STATIONS. EACH CONNECTED STATION WILL HAVE LINE 
APPEARANCE FOR OUTGOING POOLED TRUNKS WITH ACCESS 
TO CO, WATS, OR FX TRUNK CALLS. 
POOLED BOTHWAY TRUNK - ALLOWS BOTHWAY TRUNK LINES TO BE POOLED INTO A 
GROUP 
TERMINATING TRUNK GROUP CONNECTED TO MULTIPLE 
STATIONS. EACH CONNECTED STATION WILL HAVE LINE 
APPEARANCE FOR TWO-WAY POOLED...

,_. 
,-- . 
ing Trunk Terminations 
F MULTIPLE REMARKS 
ASSIGNED TO AN OUTGOING 
TRUNK GROUP 
SIMULTANEOUSLY 
POOLED BUTTONS OTHER NOT LIMITED 1 TRUNK GROUP A BOTHWAY TRUNK 
OUTGOING THAN FEATURE PER BUTTON 
ASSIGNED TO THIS TRUNK 
TRUNK GROUP ACCESS BUTTONS 
DIRECT-IN 
NO BUTTON NOT ASSIGNABLE 
NOTE: MAXIMUM OF 31 TRUNK GROUPS CAN BE ASSIGNED 
2.86  

Programming Trunk Terminations/Diagram 
of Trunk Termination Assignments 
GE m!mw sms 
BOTHWAY 
TRUNK GROUP 
DIRECT-IN + DIRECT-IN- 
--- I 
-- 
--- it if ---- ---mm 
ii k 
i t-~..-i..-.---j .-.. +.. ; r-T-y-- -.. -.. -- 
..-. . - 
! j 
i :TJ+’ 
i.., :: i  II 
i II / 
I I EKT 
I I EKT 
1 
1 
--- 
.a-- 
---- 
_-- - 
.--- 
--- 
-..-..-BOTHWAY -----0UTGOlNG 
- - - - -INCOMING 
DIRECT-IN 
2.87