GTE Omni Scbs Installation And Maintenance Manual

-. 
STATION ACCESS 
BUTTONS WITH 
LED LAMPS 
DSS 80 
III1211311411sl 270 271 272 . 273 274 275 276 277 278 279 
2.48  

odules 
efault 
. ALLOWS FOR PREPROGRAMMED STATlON BUTTON ASSIGNMENTS ON BLFIDSS 
MODULE. 
@ BLF/DSSSHOULD BEASSIIGNEDTO ODD ClRCUlT NUMBER ON 8EKC CARD INSERTED 
lNT0 CARD SLOT 01. 
@ REQUlRES THAT CS-IO OR CS-20 ASSOClATED WITH BLFIDSS MUST BE INSTALLED 
AS A STATION ON SAME 8EKC CARD IN SLOT 01. ASSOCIATED EKT SHOULD BE 
CONNECTED TO THE EVEN NUMBERED CIRCUIT ONE NUMBER LESS THAN THE 
BLFIDSS CIRCUIT NUMBER (I.E., EKT = CIRCUIT 0, BLF/DSS = CIRCUIT 1). 
jl * 
(UTILIZING DEFAULT STANDARD DATA BASE...

BLF/DSS Instr 
allatio - Man 
. ASSUMES THAT COMPLETE PROGRAMMING OF BLF/DSS CONSOLE 
IS REQUIRED. 
0 PROCEDURE USED IF DEFAULT STANDARD DATA BASE IS NOT USED 
OR IF THE BLF/DSS IS NOT CONNECTED TO AN 8EKC CARD IN CARD 
SLOT 
Ol.* 
. THE CS-10 OR CS-20 ASSOCIATED WITH THE BLF/DSS MUST 
ALREADY BE INSTALLED PRIOR TO BLF/DSS INSTALLATION. 
I PROCEDURE I 
1. 
USE CMC-210 TO ASSIGN: 
. IDENTIFYING BLF/DSS INSTRUMENT NUMBER (Pl) 
. BLF/DSS TYPE (P2) 
. EQUIPMENT NUMBER (P3) 
* ASSOCIATED EKT STATION DIRECTORY...

SS Instruments 
1 PROCEDURE 1 (CHANGE) 
C-211 TO RE VE Bls/D 
BUTTON 
ASSIGN T BEFORE 
ENTERING NEW BUTTON ASSlGNMENTS. 
8 USE CM@-2-M TO EMlOVE BLFIDSS ASSIGNMENT 
EXISTING ENTRIES MUST BE REMOVED BEFORE CHANGING 
BLWBSS MODULE ASSIGNMENTS. 
2.51  

, .- 
,, -. 
Programming BLF/DSS Modules 
CMC Corn and Summary 
CATEGORY CMC TABLE 
@ BLF/DSS 210 
ASSIGNMENT 
8 BLFIDSS BUTTON 211 
ASSIGNMENT 
2.52 
FUNCTION 
ASSIGNS OR REMOVES 
BLF/DSS MODULES. 
ASSIGNS, REMOVES, OR 
CHANGES BLF/DSS 
FEATURE OR STATION 
INTERCOM BUTTONS FOR 
EACH BLF/DSS BUTTON.  

PERFORM THE FOLLOWING PROGRAMMING TASKS IN THE SEQUENCE OUTLINED BELOW, USING THE SAMPLE WORK 
ORDERS AND IN ACCORDANCE WITH THE GTE OMI SBCS GTEP MANUAL. COMPLETE THE REVIEW EXERCISE QUESTIONS 
PERTAINING TO STATION AND BLF/DSS PROGRAMMING UPON COMPLETION OF THIS LABORATORY ACTIVITY. 
WORK ORDER #2.2 
IOMPANY NAME: NU SYSTEM CC. PHONE #: (703) 5551212 
-0CATtCN: RESTON, VIRGINIA WORK ORDER #2.2 (TASK #I) 
‘R’G’NAToR: TELECOMMUNICATIONS MANAGER 
-ASKS: 
- e Add, modify, or remove a station with CMC-200....

- Programming Station 
WORK ORDER #2.2 
ZOMPANY NAME: NU SYSTEM CO. 
-0CATlON: RESTON, VIRGINIA 
)RlGlNATOR: TELECOMMUNICATIONS MANAGER PHONE #: (703) 555-1212 
WORK ORDER #2.2 (TASK #2) 
-ASKS: 
l Restore station 215 to system by adding it with CMC-200. 
l Change station operation mode, tenant group, and SMDR metering 
group using CMC-201. 
‘ARAMETERS: INSTRUCTIONS: 
(1) Add station 215 at slot 01, circuit 07. (1) Perform programming changes for station 
instrument. 
(2) Change operation mode for SLT at...

boratory 
Instruments gramming Station 
WORK ORDER #2.2 
COMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 
-0CATION: RESTON, VIRGINIA WORK ORDER #2.2 
(TASK #3) 
I)RIGINATOR: TELECOMMUNICATIONS MANAGER 
I-ASKS: 
e Identify a station directory number as a data secure line or an 
off-premises extension with CMC-204. 
(1) Make station 214 a data secure line. (1) Perform programming changes for station 
instruments. 
(2) Designate the SLT at slot 02, circuit 7 as an off- 
premises extension. (2) Check/test...

WORK ORDER #2.2 
ZOMPANY NAME NU SYSTEM CO. 
-0CATION RESTON, VIRGINIA 
‘R’C’NATCR TELECOMMUNICATIONS MANAGER 
‘ASKS PHONE. ” (703) 555-1212 
‘WORK ORDER ff 2.2 (TASK #4) 
e Assign and remove feature assignments for EKT button with CMC-203. 
‘ARAMETERS 
(1) Assign “Call Park” to button 1 for both 
CS-20 instruments. INSTRUCTIONS 
(1) Perform programming changes for station 
instruments. 
(2) Change the “Forward All” feature assigned by 
(2) 
default to a button on station 308, to the “Do Check/test the...

ry Activity - 
Instrument 
Modules (Continued) 
WORK ORDER #2.2 
ZOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 
-0CATlON: RESTON, VIRGINIA WORK ORDER #2.2 
(TASK #5) 
IRlGlNATOR: TELECOMMUNICATIONS MANAGER 
TASKS: 
e Add, change, or delete a BLF/DSS module with CMC-210. 
‘ARAMETERS: INSTRUCTIONS: 
(1) Install and add a 40 button BLF/DSS to card (1) Perform programming changes for BLF/DSS 
01, circuit 3. (NOTE: Cross connect wiring was 
modules. 
completed during installation. Simply connect 
BLF/DSS...