GTE Omni Scbs Installation And Maintenance Manual

-, ,, : 
:, ‘1 
NUMER 
KEYS 
PRINTER 
PAPER OFF ON 
FEED 
FUNCTION KEYS 
CASSETTE COPY ADD/CHG 
DUP DSP 
RLS CAN 
L JUUU 
0 STANDARD TYPEWRITER FORMAT. 
@ SPECIAL CONTROL, KEYS TO ENABLE FUNCTION A RlNTER O~ERATIONm 
PROGRAM FUNCTION (PF) KEYS WHICH CHANGE M 
CONTROL PROGRAM OPERATION. ND FUNCTION DURlN 
@ CURSOR CONTROL KEYS FOR QUICK MOVEMENT OF CURSOR. 
@ NUMERIC KEYS FOR ENTRY OF DATA BASE PARAMETER VALUES. 
2.10  

@ USES STANDARD IWHCROCASSETTE TAPES: 
R SAVING PIMP 
PWO@RANl 
FEE DEP 
DATA BASE 
USED TO LOAD 
GR INT 
OF INITIALIZATI EMORY AT TI 
ER 
DISCHARGE. 
@ USED TO SAVE AND LOAD OFFICE DEPENDENT DATA BASE. 
2.11  

1 PROCEDURE 1 
(1) COMPLETE ANY CMC COMMAND IN PROGRESS AND ENSURE CURSOR IS DISPLAYED Oil 
SCREEN. 
(2) PRESS PRlNTER ON/OFF SWITCH (LOCATED ON SIDE OF PMP). 
(3) PRESS CONTROL KEY AND PF2 KEY SIMULTANEOUSLY. 
(4) 
AFTER SCREEN HAS PRINTED, PRESS PAPER FEED KEY TO ADVANCE PAPER FOR REMOVAL 
FROM PMP. 
NOTE: 
I. MAKE CERTAIN COMMAND PROCESS HAS BEEN COMPLETED BEFORE ADVANCING PAPE 
OR PRINTING, OR COMMAND WILL BE INTERRUPTED AND INPUT DATA WILL BE LOST. 
2. ONLY CONTENTS OF DISPLAY SCREEN IS PRIMTEti....

itilizing 
t PROCEDURE 1 
(1) 
(2) 
(3) 
(4) 
(5) CONNECT PORTABLE MAINTENANCE PANEL CABLE TO 
PORT 8. IF NOT CONNECTED ALREADY. 
POWER ON PMP BY PRESSING POWER ON SWITCH 
LOCATED ON RIGHT SIDE OF PMP. 
THE PROGRAM MENU WILL BE DISPLAYED: PRESS CONTROL AND @ KEYS SIMULTA- 
NEOUSLY. PMP WILL DISPLAY THE FOLLOWING 
SCREEN WHICH PROMPTS FOR YEAR, DATE, AND TIME: 
TYPE YEAR, DATE, AND TIME (AS IN EXAMPLE): 
f 7 
PRESS RETURM KEY, PMP WILL DISPLAY FOLLOWING 
SCREEN: 
IF MENU DOES NOT APPEAR, PRESS RESET...

1 PROCEDURE 1 
(1) TURN PMP POWER ON. 
(2) AFTER MAIN MENU APPEARS AND PORT CONFIGURATION SCREEN 
ARE DISPLAYED. 
PRESS THE BREAK KEY. 
(3) TYPE: “LQGIN2” AND PRESS RETURN. 
(4) lNSERT PMP CONTROL PROGRAM TAPE INTO CASSETTE TAPE 
DRIVE. 
(5) TYPE: “WIND” AND PRESS RETURN. TAPE WILL NOT REWIND. 
(6) TYPE: “LOA 
‘“CASHeLOA ER”” AND PRES RN. WAIT 
APPROXIMATELY FIVE MINUTES. 
(7) AFTER TAPE STOPS MOVING, INSERT BLANK TAPES. 
(8) TYPE: “WIN 
SS RETURN. TAPE WILL REWIND. 
(9) AFTER TAPE STOPS, TYPE: 
(IQ)...

2.15  

boratory Activity - Data Base verview 
Gull aww SBCS 
INSTRUCTIONS: PERFORM THE FOLLOWlNG TASKS IN THE SEQUENCE OUTLINED BELoW IN 
ACCORDANCE WITH THE STUDENT WORKBOOK, THE OMNI GTEP MANUAL AND 
PRIMER. 
WORK ORDER #2.1 
COMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 
LOCATION: RESTON, VIRGINIA WORK ORDER #2.1 (TASK #1) 
ORIGINATOR: TELECOMMUNICATIONS MANAGER 
TASKS: 
e Initialize and load PMP Control program microcassette tape. 
e Create a backup copy of the PMP Control Program. 
INSTRUCTIONS: 
(1)...

@ ACCESS CODES ARE PROVIDED FOR TWO LEVELS OF SECURITY 
(ACCESS CODES CHANGE ACCORDING TO SOFTWARE VERSION 
RELEASE). 
I SECURITY LEVELS SVRul.O.2.2, SVR.l.5.X.X AND 2.0.X,X 
(PACKAGE A) 
(PACKAGES B AND C) I 
HIGH SECURITY ACCESS 
LOW SECURITY ACCESS 
. HIGH SECURITY CODES ALLOW ACCESS TO ALL CMC TABLES. 
Q) LOW SECURITY CODES ALLOW ACCESS TO CM6 TABLES WHICH Do 
NOT HAVE CRITICAL IMPACT ON SYSTEM. 
@ REQUIRED SECURITY LEVEL IS NOTED IN CMC TABLE LISTING IN 
OMNI SBCS GTEP MANUAL. 
2.17  

@ IF HIGH LEVEL SECURITY CODE IS ENTERED AT SECURITY CODE PROMPT (AS 
ILLUSTRATED IBELOW), ALL CMC COMMANDS MAY BE ACCESSED. ENTER 
APPROPRIATE CODE FOR SOFTWARE RELEASE AND PRESS RETURN. 
SECURITY CODE = #803 
L-J 
0 IF LOW LEVEL CODE IS ENTERED AT SECURITY PROMPT AND ACCESS TO A CMC 
COMMAND REQUIRING HIGH SECURITY IS ATTEMPTED, PMP WILL DISPLAY 
“LOCKED” MESSAGE (AS ILLUSTRATED BELOW): 
NOTE: FOR SOFTWARE VERSION I.&X.X, USERS MUST PRESS SHIFT + PFI TO EXIT TO 
THE INITIAL SECURITY PROMPT. THEN THE...

PMP Control Program Access 
[PROCEDURE 1 
(1) POWER ON PMP. A SCREEN DISPLAYING 
MAIN PROGRAM MENU AND COPYRIGHT 
INFORMATION WILL APPEAR BRIEFLY AND 
THEN DISAPPEAR. PMP PORT CONFIGURATION 
WILL BE DISPLAYED: 
f 1 
PORT CONFIGURATION 
CHANGE? 
YES OR NO (YIN) 
(2) ENTER: N DO-URN. 
THIS WILL SKIP PORT CONFIGURATION 
SCREENS AND ASSUME DEFAULT VALUES 
WHICH ARE PRESENT TO MATCH OMNI SBCS 
DEFAULT PORT 0 CONFIGURATION. 
(3) SECURITY CODE PROMPT WILL NOW BE 
DISPLAYED: f-1 
SECURITY CODE= 
ENTER DESIRED...