GTE Omni Scbs Installation And Maintenance Manual

., 
-. 
Laboratory Activity (1.4) - Start Up 
and hi ization 
(1) 
(2) 
(31 
(4) 
(5) 
03 
(7) 
(8) 
ENSURE THAT POWER SUPPLY AC PLUG IS NOT CONNECTED TO THE 110 VAC RECEPTACLE AND 
THAT THE POWER SUPPLY SWITCH IS OFF. 
CONNECT THE CABINET POWER SUPPLY CABLE TO OMNI SBCS CABINET. 
CONNECT THE POWER SUPPLY AC PLUG TO THE 110 VAC RECEPTACLE AND TURN THE POWER 
SUPPLY SWITCH TO THE ON POSITION. 
VERIFY THAT THE OPE LAMP ON THE POWER SUPPLY AND THE RUN LAMP ON THE CPM CARD 
ARE LIT. (BOTH LAMPS ARE GREEN)....

. 
Laboratory Activity (1.4) 
Initialization (Continued) 
(11) CLEAR YOUR LABORATORY INSTALLATION SITE OF ALL DEBRIS AND REMNANTS OF THE 
INSTALLATION. SAVE ALL BOXES AND STACK THEM NEARBY YOUR LABORATORY AREA FOR 
LATER USE. 
LAB MILESTONE: 
l VERIFY THAT THE SYSTEM IS OPERATIONAL. 
. ASK INSTRUCTOR TO INSPECT YOUR FINAL SYSTEM INSTALLATION, IMPLEMENTATION 
START UP, AND INITIALIZATION TASKS. AFTER INSPECTION, INSTRUCTOR WILL INITIAL 
YOUR PERFORMANCE CHECKLIST. 
l YOU HAVE NOW COMPLETED OMNI SBCS...

Rewiew Exercise (1.4) 
INSTRUCTIONS: THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, FILL IN THE BLANK 
OR MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E. STUDENT 
WORKBOOK, NOTES, AND GTEP MANUAL) MAY BE USED AS REFERENCES. SUBMIT 
EXERCISE TO INSTRUCTOR FOR GRADING WHEN LAST QUESTION HAS BEEN 
COMPLETED. 
1. MATCH EACH CPM INDICATOR WITH THE CORRECT DESCRIPTION OF ITS FUNCTION WHEN LIT: 
RUN LED (GREEN) (A) INDICATES THAT SOFTWARE HAS DETECTED A 
FAILURE IN ONE OR MORE AREAS OF SYSTEM...

Review Exercise (1.4) - Start Up 
and 
itializatis 
3. WHAT TYPE OF RESTART/RESET LOADS THE DEFAULT STANDARD DATA BASE INTO ROM AND 
EPROM? 
4. WHAT TYPE OF RESTART/RESET IS PERFORMED AUTOMATICALLY BY THE SYSTEM TO 
RECOVER FROM A POWER FAILURE? 
5. WHAT VISUAL EVIDENCE INDICATES THAT A COLD RESTART HAS BEEN PERFORMED, ASSUMING 
THAT CS-20 OR CSD TELEPHONES HAVE BEEN INSTALLED? 
6. WHAT TYPE OF RESTART/RESET REQUIRES REPROGRAMMING OR RELOADING THE CUSTOMIZED 
DATA BASE FROM TAPE OR DISKETTE? 
7. WHAT IS...

MODULE II 
ATA BASE  

Table of Co 
OVERVIEW 
DATA BASE ADMINISTRATION (OBJECTIVES) 
.................................................... 2.3 
OVERVIEW-SYSTEMDATABASE ............................................................ 
2.4 
DATABASECAPABILITIES ................................................................... 2.5 
PROGRAMMING TOOLS AND EQUIPMENT 
...................................................... 2.6 
PORTABLE MAINTENANCE PANEL 
............................................................. 2.7 
CABLE CONNECTION...

DEFAULT STANDARD DATA BASE 
. STATUS AND CAPACITY 
............................................................... 2.27 
. STANDARD STATION NUMBERING PLAN 
.................................................. 2.28 
. DEFAULT STANDARD ASSIGNED FEATURES AND ACCESS CODES 
............................. 2.29 
. DEFAULT STANDARD TIMING VALUES 
2.31 
. DIALED OUTPULSED RECOGNlZE/SEND’iliil’ : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2.32 
. GUIDE TO OMNI SBCS...

ble 
of Co 
named) 
PROGRAMMING TRUNK TERMINATIONS 
. PROGRAMMING TRUNK TERMINATIONS (OBJECTIVES) 
. OVERVIEW OF PROGRAMMING TRUNK TERMINATIONS 
. TRUNK/STATION/EKT BUTTON ASSIGNMENTS . . . . . . 
. TRUNK TERMINATION ASSIGNMENTS 
l DIRECT-IN LINE ASSIGNMENT . . . . . . : : : : : : : : : : : : : : 
. KEY SYSTEM TRUNK LINE ASSIGNMENT . . . . . . . . . . . . 
. PERSONAL/PRIVATE TRUNK LINE ASSIGNMENT . . . . . 
. POOLED INCOMING TRUNK LINES ASSIGNMENT . . . . . 
. POOLED OUTGOING TRUNK LINES ASSIGNMENT . . ....

PROGRAMMING CLASS OF SERVICE (Continued) 
. LABORATORY EXERCISE (2.6) 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 
2.128 
. REVlEWEXERClSE(2.6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ::::::::::::::::::::::::::::: 2.132 
SYSTEM-WIDE PROGRAMMING CHANGES 
. SYSTEM-WIDE PROGRAMMING CHANGES (OBJECTIVES) 
. NUMBERING PLAN ASSIGNMENT 
................... 
. SERVICE PARAMETER ASSIGNMENT 
................ 
o SYSTEM TIMING PARAMETER ASSIGNMENT 
........... 
. SYSTEM...