GTE Omni Scbs Installation And Maintenance Manual

Laboratory Activity (1.3) 
- Peripheral 
(1) USING 25 PAIR CABLES WITH MALE CONNECTORS ON ONE END, CONNECT FIVE CABLES TO THE 
FOLLOWING RECEPTACLES: CN 0, CN 1, CN 10, CN 11, CN 12. 
(2) RUN CABLES NEATLY FROM THE OMNI SBCS CABINET USING SCREWS TO FASTEN THE 
CONNECTORS TIGHTLY TO THE RECEPTACLES. CONNECT EACH CABLE TO THE CDF BLOCK 
DESIGNATED BELOW: 
(A) CN 0 - FIRST STATION CDF BLOCK 
(B) CN 1 - SECOND STATION CDF BLOCK 
(C) CN 10 - FIRST STATION CDF BLOCK 
(D) CN 11 - SECOND STATION CDF BLOCK 
(E)...

tory ffktivity (1.3) - Peripheral 
tion (Contin 
(4) WIRE CROSS CONNECTIONS AND INSTALL THE FOLLOWING STATION INSTRUMENTS USING THE 
DESIGNATED CONFIGURATIONS: 
-.- (A) 
- (W 
CG’ (C) 
-/CD) 
J (El 
u:.l (F) 
‘ii! (G) 
b’: (H) 
LA) 
’ (J) 
CS-10 TELEPHONE USING 8EKC CARD IN SLOT 01, CIRCUIT 0. DEFAULT STATION 
DIRECTORY NUMBER WILL BE 208. DO NOT CONNECT THIS STATION TO THE MODULAR 
JACK AT THIS TIME. IT WILL BE ADDED DURING A DATA BASE PROGRAMMING LAB 
ACTIVITY. 
CS-10 TELEPHONE USING 8EKC CARD IN SLOT...

Laboratory Activity 
(1.3) - Peripheral 
Hnstallatio (Continue 
GTE OMNU SBCS 
(6) WIRE CROSS CONNECTIONS FOR THE POWER FAIL TRANSFER STATION: 
(A) SINGLE LINE TELEPHONE INSTRUMENT USING 8SLC CARD IN SLOT 02, CIRCUIT 0 TO POWER 
FAIL TRANSFER CDF BLOCK. 
(B) POWER FAIL TRANSFER CARD (GPFT) IN SLOT 22, CIRCUIT 0 TO CO TRUNK ON 4BWC CARD 
IN SLOT 18, CIRCUIT 0. 
LAB MILESTONE: 
e VERIFY THAT POWER FAIL TRANSFER CROSS CONNECTIONS ARE WIRED CORRECTLY. 
. ASK INSTRUCTOR TO INSPECT THE CROSS CONNECTIONS AND...

(7) VERIFY THAT POWER FAlL TRANSFER TRUNKS HAVE BEEN INSTALLED FROM CARD SLOT 18, 
CIRCUIT 0. WIRE CROSS CONNECTIONS AND INSTALL THE FOLLOWING TRUNK LINES USING THE 
DESIGNATED CONFIGURATIONS: 
(A) THREE ADDITIONAL CO TRUNK LINES USING 4BWC CARD IN SLOT 18, CIRCUITS 1,2, 
AND 3. 
(B) TWO LOOP TIE LINES USING 2TTL CARD IN SLOT 16, CIRCUITS 0 AND 1. THESE TIE 
LINES WILL BE USED TO ACCESS OTHER OMNI SBCS LAB SYSTEMS. INSTRUCTOR 
WILL PROVIDE INSTRUCTIONS REGARDING CONNECTION. 
(6) TWO E&M TIE LINE (TYPE...

(8) CONNECT PORTABLE MAINTENANCE PANEL (PMP) TO OMNI SBCS CABINET. CONNECT DIN 
PLUG OF EPSON CABLE #715 TO PORT MARKED “RS-232-C” ON BACK OF PMP. CONNECT DB-25 
CONNECTOR END OF CABLE TO PORT CN13 (I/O 0) ON THE SBCS CABINET. 
(9) ENSURE THAT BOTH OMNI SBCS AND PMP POWER SWITCHES ARE OFF. 
(10) INSTALL FLOPPY DISKETTE UNIT TO PMP USING PROCEDURE FOUND IN THE STUDENT 
WORKBOOK. DO NOT POWER ON THE PMP OR FLOPPY DISKETTE DRIVE UNIT UNTIL 
INSTRUCTED TO DO SO DURING THE INITIALIZATION LAB ACTIVITY. 
(11)...

COMPLETE ALL OR PART OF THE FOLLOWlNG ACTIVITY IF TlME PERMITS OR IF INSTRUCTOR 
DIRECTS YOU TO DO SO. 
(1) WIRE CROSS CONNECTIONS AND INSTALL ONE OR BOTH OF THE FOLLOWING OPTIONAL 
PERIPHERAL EQUIPMENT USING THE DESIGNATED CONFIGURATIONS BELOW: 
(A) NIGHT BELL USlNG 8SLC CARD IN SLOT 02, CIRCUIT 3. 
(B) MUSIC SOURCE FOR MUSIC-ON HOLD USING 4BWC CARD IN SLOT 18, CIRCUIT 2. 
LAB MILESTONE: 
8 VERIFY THAT NIGHT BELL AND MUSIC SOURCE ARE WIRED AND INSTALLED 
CORRECTLY. 
@ ASK INSTRUCTOR TO INSPECT CROSS...

Review Exercise (1.3) - Peripheral 
I tisn 
INSTRUCTIONS: THE FOLLOWING EXERClSE CONSISTS OF MULTIPLE CHOICE, FILL IN THE BLANK 
OR MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E. STUDENT 
WORKBOOK, NOTES, AND GTEP MANUAL) MAY BE USED AS REFERENCES. SUBMIT 
EXERCISE TO INSTRUCTOR FOR GRADING WHEN LAST QUESTION HAS BEEN 
COMPLETED. 
1. WHAT CARD SLOTS AND CIRCUITS DO THESE SYSTEM CABLES SUPPORT (ALL SPACES WILL NOT 
BE REQUIRED); 
CABLE CARD SLOT / CIRCUITS CARD SLOT / CIRCUITS CARD SLOT / CIRCUITS...

ewiew 
4. COMPLETE THE FOLLOWING DIAGRAM INDICATING THE CROSS CONNECTIONS THAT WERE 
MADE FOR THE SIX EKT TELEPHONES. ONE OF THE CS-10 TELEPHONES HAS BEEN COMPLETED, 
AS AN EXAMPLE. 
cs-20 
(CKT4) _ - 
_ - 
_ - 
_ - 
_ - 
_ - 
_ - 
_ - 
_ _ 
_ - 
_ - 
_ - 
_ - 
_ - 
_ - 
_ - 
_ - 
_ - 
” - 
_ - 
_ - 
_ - 
_ - 
_ - 
_ _ 
_ - 
_ - 
- - 
_ - 
_ - 
_ - 
_ - 
- - 
_ - 
_ - 
_ - 
_ - 
_ _ 
_ - 
_ - 
_ - 
CABLE 0. MODULAR 
JACK 
CABLE 1 
cs-10 
(CKTO)  

eview Exercise (1.3) - Peripheral 
ati 
5. COMPLETE THE FOLLOWING DIAGRAM INDICATING THE CROSS CONNECTIONS THAT WERE 
MADE FOR THE TWO SINGLE LINE TELEPHONES. 
CABLE 1 - - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
1.80 SLT 
(CKTO) 
I I 
ET2 t 
0 
SLT 
(CKT7)  

ewiew Exercise 
7. COMPLETE THE FOLLOWING DIAGRAM INDICATING THE CROSS CONNECTIONS THAT WERE 
MADE FOR THE POWER FAILURE TRANSFER INSTALLATION (INCLUDE TRUNK AND 
INSTRUMENT 
CROSS CONNECTIONS, AS WELL AS CROSS CONNECTIONS TO THE THREE CARDS). 
CABLE 1 
(TO 8SLC) - - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - - - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - - - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
1.81