GE S5 Owners Manual
Here you can view all the pages of manual GE S5 Owners Manual. The GE manuals for Medical Monitor are available online for free. You can easily download all the documents as PDF.
Page 51
Functional check43 Document no. M1187317-009 Preset the measurement settings for those parameters that are connected, for example: Print/Recorder - Record Waveforms - Waveform 1 - ECG1 - Waveform 2 - P1 - Waveform 3 - P2 Invasive Pressures - P1 ‘ART’ Setup -- Label – ART - P2 ‘CVP’ Setup -- Label – CVP Others -SPO2 Setup - Pleth Scale –AUTO Airway Gas - CO2 Setup - Resp Rate Source – AUTO - Measurement – ON - Detection Limit – AUTO 5.3.2 Display 1. Check that the...
Page 52
Datex-Ohmeda S/5 FM 44 Document no. M1187317-009 Breathe to the sampling line briefly. Check that the CO2 information is updated on the screen. 5.3.6 Multiparameter Hemodynamic Modules ECG and RESP measurements 1. Connect an ECG cable to the module. Connect the cable leads to a patient simulator. Check that all ECG and impedance respiratio n information is shown on the monitor screen as configured on the simulator. Turn the simulator off. Check that the ‘Asystole’ and ‘Apnea’ messages appear on the...
Page 53
Functional check45 Document no. M1187317-009 5.3.7 Data Card and Menu Card function 1. Insert a Data card or a Menu card to the slot.Check that the corresponding symbol appears on the monitor screen. 5.3.8 Recorder 1. Press the Start/Stop sidepanel key and check that the module starts recording the selected waveforms. Press the Start/Stop sidepanel key again to stop recording. 2. Check that the quality of the recordings is acceptable. 5.3.9 Network connection 1. Check that the Mon-Net cable...
Page 54
Datex-Ohmeda S/5 FM 46 Document no. M1187317-009 5.3.12 General• Switch the monitor to standby •Perform final cleaning •Fill in all necessary documents
Page 55
General troubleshooting47 Document no. M1187317-009 6 General troubleshooting Figure 11 S/5 FM general troubleshooting flowchart No picture on screen Main CPU board may be faulty. Yes No NIBP pump starts pumping and SpO2 probes red LED lit?No No FM_general_trbl_flowchart.vsd Disconnect the mains power cord and remove the batteries to make a cold start. Connect the mains power cord Check the batteries charging levelsby pressing the test buttons on the batteries. Insert only one battery with 2 or...
Page 57
Appendix A Functional check form, Datex-Ohmeda S/5 FMA-1(2) Document no. M1187317-009 APPENDIX A: Functional check form, Datex-Ohmeda S/5 FM OK = Test OK N.A. = Test not applicable Fail = Test failed Customer Service Service engineer Date Measuring equipment / test gases used: Equipment / tool / gas: Manufacturer: Model/Type/Part Number: Serial Number / ID:Calibration Date: Monitor Installation L- E- N- F- Visual Inspection OK...
Page 58
Datex-Ohmeda S/5 FM A-2(2) Document no. M1187317-009 5.3.6. Multiparameter Hemodynamic ModulesS/N . ECG and RESP measurements . Temperature measurement . Invasive blood pressure measurement . SpO2 measurement . Non invasive blood pressure measurement 5.3.7. Data Card and Menu Card function 5.3.8. Recorder...
Page 59
Appendix B ElectroMagnetic CompatibilityB-1(4) Document no. M1187317-009 APPENDIX B: ElectroMagnetic Compatibility Table 1 Guidance and manufacturer’s declaration – electromagnetic emissions (1 S/5 FM equipped with S/5 Frame for FM, F-FM (2 S/5 FM equipped with S/5 Frame for FM with WLAN, F-FMW Guidance and manufacturer’s declar ation – electromagnetic emissions The S/5 FM is intended for use in the electromagne tic environment specified below. The customer or the user of...
Page 60
Datex-Ohmeda S/5 FM B-2(4) Document no. M1187317-009 Table 2 Guidance and manufacturer’s declaration – electromagnetic immunity Guidance and manufacturer’s decl aration – electromagnetic immunity The S/5 FM is intended for use in the electromagnetic en vironment specified below. The customer or the user of the S/5 FM should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Electromagnetic environment - guidance Electrostatic discharge (ESD) IEC...
All GE manuals