GE S5 Owners Manual

 Introduction13
Document no. M1187317-009
1.2.2 ESD precautionary procedures •
To avoid electrostatic charges building up, it is recommended to store, maintain and use 
the equipment at a relative humidity of 30% or greater. Floors should be covered by ESD 
dissipative carpets or similar. Non-synthetic clothing should be used when working with 
the component. 
•To prevent applying a possible electrostatic di scharge to the ESD sensitive parts of the 
equipment, one should touch the metallic fram e of the...

Datex-Ohmeda S/5 FM
14
Document no. M1187317-009
2 System description
2.1 Introduction
Datex-Ohmeda  monitors build up a freely configurable modular system. The architecture is 
designed to enable different module combinations so that the user is able to get the desirable 
parameter and feature set. This modular approach makes it possible to add new features 
when they are needed.
2.2 Bus structure
The operation of Datex-Ohmeda FM is based  on two communication channels, the CPU bus 
and module bus. All...

 System description15
Document no. M1187317-009
The RS-485 type of serial communication su pports so-called multidrop or party line 
connections. This means that all parameter modules connected to the module bus use exactly 
the same lines for communication. The advant age of this is that all bus connectors are 
identical and the modules can be connected in any order and position.
2.3 Distributed processing
A system assembled from Datex-Ohmeda products  is a multiprocessor system. All parameter 
modules...

Datex-Ohmeda S/5 FM
16
Document no. M1187317-009
The UPI processor collects and stores all data that is received from the parameter modules into 
a shared SRAM, which is mapped directly to the address space of the main CPU. The main CPU 
reads data from the memory while the UPI processor guarantees that the data is up to date. 
This operation also works in the other direction. In this the main CPU fills the shared SRAM with 
data and the UPI processor distributes it to the parameter modules.
2.5 Software...

 System description17
Document no. M1187317-009
2.6 Parameter modules
Figure 4 General structure of parame ter modules with patient isolation
The detailed structure of a parameter module  depends on the specific needs for each 
individual parameter. However, some common parts are used in the parameter modules. The 
electronics inside the module  is usually divided into isolated (floating) and non-isolated 
sections. Typically, the non-isolated section cons ists of buffers to interface the parameter...

Datex-Ohmeda S/5 FM
18
Document no. M1187317-009
3 System installation
3.1 Unpacking instructions
1. Confirm that the packing box is undamaged. If the box is damaged, contact the shipper.
2. Open the top of the box and carefully unpack all components.
3. Confirm that all components are undamaged. If any of the components is damaged, contact the shipper.
4. Confirm that all components are included. If any of the components is missing, contact  your GE Healthcare distributor.
3.2 Choosing location
Consider...

 System installation19
Document no. M1187317-009
Figure 5 E-PSM(P) mounting accessories
1. M1051025 Module Bus Adapter for PSM
2. M1049197 Pole Mount for PSM, short
3. M1051023 Pole Mount for PSM, long
WARNINGMake sure that the Pole Mo unt for PSM is always used in vertical position to 
prevent water from enteri ng the E-PSM(P) module.
Pole Mount for PSM – Instructions for  connecting to an IV pole, vertical 
position
Pole Mount for PSM - Instructions fo r installing in horizontal position.
Remove the 2...

Datex-Ohmeda S/5 FM
20
Document no. M1187317-009
3.3.2 Monitor connections
Figure 6 S/5 FM front panel
(1) Battery compartment
(2) Transportation handle
(3) Alarm light
(4)  Alarm LED indicators
(5)  Side panel keys
(6) The ComWheel
(7)  Command Board keys
(8)  Guide rail for GCX mounting
(9)  Mains power and battery LEDs
(10) ON/standby key
(11)  Connector for the Device Interfacing Solution (X6)
(12) Connector for defibrillator synchronization (X5)
(13) Measurement modules
(14)  Slot for Data Card or...

 System installation21
Document no. M1187317-009
 
Figure 7 Rear panel connections 
(1)  Slot for infusion pole mounting
(2) Module connector
(3)  Guide rail for GCX mounting
(4)  Receptacle for power cord
(5) Fuse holder
(6) Serial port X9
(7)  Network ID X8
(8)  Connector for K-CREMCO X7
(9)  Optional: Multi I/O adapter incorporating connectors 6 - 8 mentioned above
(10)  Network connector X1
(11) Equipotential connector
(12)  Slot for Data Card or Menu Card
(13)  Defibrillator & IABP sync connector X5...

Datex-Ohmeda S/5 FM
22
Document no. M1187317-009
3.3.3 Connection to mains
Connect the power cord to the mains power inlet (4) at the back of the monitor and to the wall 
socket.
NOTE: Before taking the monitor into use for the  first time, the batteries should be fully charged. 
Keep the monitor connected to the mains until the Battery charging symbol disappears, or in 
STBY mode the Orange Battery condition LED is off  (may take up to 5 hours if the batteries are 
fully discharged).
WARNING The power...