Digital Projection Titan Xg-500 User Manual

Rev B 02/2007 Page 4.19
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
Input Menu
 Presets
Input Menu
 Presets
    Recall Presets A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters 
saved for each Preset are:
all...

Page 4.20 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
Input Menu
 Presets
    Save Presets A ~ H Save Presets
Press  and   to select Save Preset.
 Press 
 to open the Save Presets A ~ H submenu.
To save the current set of parameters, press 
 and   to select one of the 
Presets.
 For Presets J to S, select Save Preset J ~ S then press 
 to open the 
J~S...

Rev B 02/2007 Page 4.21
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Picture Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is 
available for Composite, S-
Video and...

Page 4.22 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  For more information about 
User gamma settings, see 
section 5. DP Userware.
 Parametric Gamma adjustment 
is available only when 
Parametric is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for graphics based 
RGB sources only.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied. The...

Rev B 02/2007 Page 4.23
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings made in 
the Geometry menu.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio.
 Press 
 and   to select from:
Fill  This...

Page 4.24 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Geometry Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Aspect Ratio selection can be 
found in both the Picture and...

Rev B 02/2007 Page 4.25
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
 Horizontal and Vertical 
Aspect Ratio adjustments are 
available only when User is 
selected in Aspect Ratio, (see 
previous page).
 Keystone adjustment can be 
found in both the Geometry and 
Projector Setup menus.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for graphics based 
RGB sources only.
 Pixels adjustment  is available 
for graphics based RGB...

Page 4.26 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Blanking
Blanking curtains can be applied to each edge of the picture.
Press 
 and   to select Blanking.
 Press 
 to open the Blanking submenu.
Blanking On/Off
 Press  and   to select from:
On
Off
Blanking adjust
Press  and   to select the edge to be Blanked.
 Press 
 and   to adjust the slider (0 to 200). •
•
•
Notes
Geometry Menu
 Blanking
  The blanking curtains will not 
applied until Blanking is turned...

Rev B 02/2007 Page 4.27
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Colour Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in 
the Colour menus.
Colour menu
  To return to the main menu, press  up to three...

Page 4.28 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
 The Colour Temperature 
slider is available  only if 
Temperature Mode is selected.
 The RGB Lift and Gain sliders 
are available  only if User Mode 
is selected.
 The Component Type selection 
is available  for RGB1, RGB2 
and Component inputs only.
Colour Mode
Press  and   to...