Digital Projection Titan Xg-500 User Manual

Rev B 02/2007  Page 5.1
5. Userware
Contents 

Page 5.2 Rev B 02/2007
5. Userware  Digital Projection TITAN XG-500 User Manual 

Rev B 02/2007  Page 6.1
6. Maintenance
Contents
Changing the lamp module .............................................................................................................. 6.2
Changing the air fi lter ........................................................................................................................ 6.3
Cleaning ................................................................................................................................................ 6.4
Projector...

Page 6.2 Rev B 02/2007
6. Maintenance  Digital Projection TITAN XG-500 User Manual
Changing the lamp module
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the three door screws, and detach the rear door - the door is tethered, 
so cannot be removed completely.
Disconnect the timer cable from the lamp module.
Loosen the two captive fi nger screws securing the lamp module.
Pull the lamp module to the right, then to the rear to remove it from the projector.
Insert a new lamp module,...

Rev B 02/2007 Page 6.3
Digital Projection TITAN XG-500 User Manual  6. Maintenance
Changing the air fi lter
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the three door screws, and remove the rear door.
Pull out the air fi lter.
Fit a new air fi lter.
Re-fi t the rear door, making sure that the door tether is not trapped, and tighten 
the three screws. •
•
•
•
•
Notes
 Always allow the lamp to cool 
for 5 minutes before:
 - disconnecting the power
- moving the projector
- changing the...

Page 6.4 Rev B 02/2007
6. Maintenance  Digital Projection TITAN XG-500 User Manual
Notes
 Never use strong detergents 
or solvents such as alcohol 
or thinners to clean the 
projector and lens.
 NEVER touch the lamp or 
refl ector.
Cleaning
Turn the projector off before cleaning.
Projector
Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild 
detergent.
Lens
Use a blower or lens paper to clean the lens, taking care not to scratch the glass.
Lamp module
Use a blower or lens paper...

Rev B 02/2007  Page 7.1
7. Appendix
Contents
Troubleshooting .................................................................................................................................. 7.2
Specifi cations ...................................................................................................................................... 7.4
Part numbers .................................................................................................................................... 7.4
Optical...

Page 7.2 Rev B 02/2007
7. Appendix  Digital Projection TITAN XG-500 User Manual
Troubleshooting
Problem Possible solutions
The projector will not power up.Check that the mains plug is plugged in and that the mains supply is switched on.
Check any external fuses or breakers.
The projector shuts down after it has 
been in use for some time.The projector may be overheating. Check that the air inlets and outlets are clear 
of any obstruction. Check that the air fi lter is clean, and if it is dirty, fi t a new...

Rev B 02/2007 Page 7.3
Digital Projection TITAN XG-500 User Manual  7. Appendix
Problem Possible solutions
Projector does not respond to control 
commands from a computer.Check that the LAN or serial cable is connected correctly.
See this section 7. Appendix, Connections
If using a LAN, check that the address setting is made correctly.
See section 4. Controlling the projector, Network menu
If using a serial cable, check that the baud rate is set correctly.
See this section 7. Appendix, Connections
Check...

Page 7.4 Rev B 02/2007
7. Appendix  Digital Projection TITAN XG-500 User Manual
Specifi cations
Part numbers
Projector 106-239
Rigging frame  104-923
Power cable 10A, Europe  102-163
Power cable 13A, North America  102-165
Power cable 10A, United Kingdom  102-180
Remote control  105-023
4x AAA  batteries  105-922
Remote cable 5m  102-162
User manual on CD  105-923C
Important Information  105-924B
Replacement parts
Lamp module  001-742
Air fi lter  102-064
Lenses
0.8 : 1 fi xed lens  001-734
1.2 : 1 fi xed...