Digital Projection Titan Xg-500 User Manual

Rev B 02/2007 Page 3.3
Digital Projection TITAN XG-500 User Manual  3. Getting Started
Notes
  For more detailed information 
about:
  - using the control keys on the 
remote control or keypad,
  - using the menus,
  see the next section: 
Controlling the projector.
  When any of the three Lens 
adjustment keys is pressed, the 
blue Transmit indicator on the 
remote control will light for 10 
seconds:
  - after 10 seconds, if no 
adjustment has been made, 
the indicator will go out and 
the Lens...

Page 3.4 Rev B 02/2007
3. Getting Started  Digital Projection TITAN XG-500 User Manual
Adjusting the projected image
Picture settings
Press a  key, followed by  and   to adjust these picture settings:
 Brightness   
 BRI
Contrast  
 CON
Saturation  
 SAT
Phase  
 PHASE
Aspect ratio   
 ASPECT
Geometry settings
Press Keystone  KEYST
followed by 
 and  to adjust the keystone correction.
Press Position  
 POS  (for all inputs except DVI)
followed by 
, ,  and  to adjust the picture position, for images...

Rev B 02/2007  Page 4.1
4. Controlling the projector
Contents
Overview ............................................................................................................................................... 4.4
Controlling the projector..................................................................................................................... 4.4
Input modes and settings ......................................................................................................................

Page 4.2 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Using the menus ............................................................................................................................... 4.15
Navigating menus and submenus ..................................................................................................... 4.15
Menu controls...

Rev B 02/2007 Page 4.3
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Setup menu ........................................................................................................................................ 4.30
Projector ........................................................................................................................................ 4.31
Orientation...

Page 4.4 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Overview
Controlling the projector
The projector can be controlled from:
the remote control
the keypad
the RS232 input
the Ethernet input
For more information about controlling the projector using the RS232 and 
Ethernet inputs, see Remote communications protocol in section 7. 
Appendix.
For information about how to connect the projector, see Connecting the 
projector in section 2. Installation, and...

Rev B 02/2007 Page 4.5
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Input modes and settings
Input mode detection
The projector can automatically detect the following parameters from the incoming 
video signal:
line frequency
frame rate
interlace / progressive
From these parameters the projector can determine input mode, for example:
 input source  horizontal  vertical     mode
composite 15.7KHz  50.0Hz = NTSC
RGB1 31.5KHz 60.0Hz = SDTV 480p
DVI 31.25KHz 50.0Hz = SVGA
When...

Page 4.6 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Any subsequent changes that you make to the modal settings will be saved in the 
mode history,  with the input mode.
If a new signal is detected, the mode history for the previous signal will be saved in 
the mode history, and the new mode added, along with a new set of default settings. 
Thus the projector builds up a history of input modes, and the required settings for 
each mode, depending on actual...

Rev B 02/2007 Page 4.7
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Indicators
Input status indicators
The indicator next to each input connector on the input panel will light as follows:
 off = input not selected
 green = input selected, signal detected and in range
 fl ashing green  = input selected, but signal not detected or out of range
Notes
  There are more indicators on 
the Control panel, and these are 
described on the next page.
  Input 4. is not used on this...

Page 4.8 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
The control panel
Keypad layout
The controls on the keypad are identical to those at the top of the remote control, 
and are described on the following pages.
Projector status indicators
The indicators on the control panel are as follows:
Power off = NO POWER
 green = normal RUNNING mode amber = STANDBY mode
Shutter amber = CLOSED green = OPEN
Error off = NO ERROR
 fl ashing = ERROR (temperature) steady =...