Digital Projection Titan Xg-500 User Manual

Rev B 02/2007 Page 4.9
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
The remote control
Layout
Timeout
There is a 10 second timeout for the three Lens adjustment keys (see note on next 
page).
There is a separate, adjustable timeout for the On Screen Menus (see On Screen 
Display, in Setup Menu, later in this section).
Notes
  Many features are controlled 
from the menus using the menu 
navigation keys on the remote 
control or keypad.
 For more information about 
using the...

Page 4.10 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  Closing the shutter produces 
a better black than simply 
removing the signal, as the 
light source will be completely 
blocked by the shutter blade.
  When the OSD is OFF:
  -  all menu navigation keys are 
disabled.
  - keys such as 
 BRI 
(brightness) will still function, 
but the slider bars will not be 
visible on screen.
  When any of the three Lens 
adjustment keys is pressed, the 
blue...

Rev B 02/2007 Page 4.11
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Auto-detect input mode
Press  to force the projector to re-detect the input mode
(see Input modes and settings, earlier in this section).
Source information
Press  to display the source information screen.
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. (not used in this projector)
5. Composite Video
6. S-Video
7. Component
Or press the numbered keys 1–7...

Page 4.12 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
  A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied.
  For more information about 
input modes, see Input modes 
and settings. earlier in this...

Rev B 02/2007 Page 4.13
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
  The red, green and blue keys 
are disabled when the OSD is 
switched OFF.
 The Saturation control is 
available for Composite, S-
Video and Component inputs 
only.
 The Phase control is available 
for RGB inputs only.
  For all adjustments on this page 
that require more than one key 
to be pressed:
  - after 10 seconds, if no 
adjustment has been made,  the  
 key must be pressed again 
to resume...

Page 4.14 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  The magnify feature utilises a 
digital zoom. Used with the pan 
control, this can be used to:
  - enlarge a section of the image
  - enable the use of multiple 
projectors to construct a large 
image from tiles.
  The pan control is available 
only when the image has been 
magnifi ed.
  If the OSD moves off screen 
due to a change in image size, 
then pressing the size key will 
restore its...

Rev B 02/2007 Page 4.15
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When the OSD is OFF, all menu 
navigation keys will be disabled.
  When the OSD is switched back 
ON, the menus will remain OFF 
until the  
 key is pressed 
again. The menus will then 
reopen at the same point they 
were last viewed.
  If a menu is opened, and no 
other key is pressed within the...

Page 4.16 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Press  to open the menu. The blue highlight moves to the fi rst item in the 
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press 
 and  , for example the Lamp submenu.
Press 
 to open the submenu. The submenu opens, with the title at the top.
To close the submenu and return to the previous level, press 
.
There may be up to three levels of submenu, so to return to...

Rev B 02/2007 Page 4.17
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Slider bar
The highlighted slider bar shows which 
control is active currently.
To adjust the slider press 
 and .
Parameter selection
To select from a number of parameters, 
(shown one at a time to the right), 
press 
 and .
These two items are greyed out and 
the values are blank, showing that they 
are not available, due to the effect of 
settings made in other menus, or due 
to the type of input signal....

Page 4.18 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Input menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Input is highlighted.
Press 
 to open the Input menu. The blue highlight moves to the fi rst item in 
the menu. The 
 symbol shows which input is currently selected.
Input Source
Press  and   to select from:
1. RGB1
2. RGB2
3. DVI
4. (not used in this projector)
5. Composite Video
6. S-Video
7....