Digital Projection Titan Xg-500 User Manual

Rev B 02/2007 Page 2.11
Digital Projection TITAN XG-500 User Manual  2. Installation
Notes
  Make sure the rear lens cap is 
removed, before fi tting the lens.
  Make sure the front lens cap is 
removed, before switching on 
the projector.
  Be careful not to scratch 
the lens surfaces. If you do 
accidentally touch a lens, then 
clean the surface using a lens 
paper.
Fixing 
screws
Fitting the lens
Remove the rear lens cap from the lens.
Insert the lens into the lens mount with the connector to the...

Page 2.12 Rev B 02/2007
2. Installation  Digital Projection TITAN XG-500 User Manual
Notes
  For more information on using 
the Lens shift feature, see 
section 4. Using the menus, 
Lens menu.
  If the lens is to be shifted in 
two directions combined, the 
maximum range is somewhat 
less, as can be seen below 
(zoom lens shift shown).
full horizontal and vertical shift
without distortion
combined shift without distortion
is reduced
Shifting the image
The normal position for the projector is at the...

Rev B 02/2007 Page 2.13
Digital Projection TITAN XG-500 User Manual  2. Installation
Notes
 BEFORE INSTALLING THE 
PROJECTOR, READ ALL THE 
WARNINGS BELOW AND 
ALL THOSE IN IMPORTANT 
INFORMATION AT THE 
FRONT OF THIS MANUAL.
 The projector weighs 
approximately 27 kg (50 lbs). 
Use safe handling techniques 
when lifting the projector.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector 
is capable of supporting 
the combined weight of 
the projector and lens (see 
specifi...

Page 2.14 Rev B 02/2007
2. Installation  Digital Projection TITAN XG-500 User Manual
Adjusting the rigging frame
Coarse adjustment of projector level should be made by adjusting the length of 
the supporting wires or chains, or by adjusting the position of the truss or rigging. 
Once the initial coarse adjustment has been made, fi ne adjustment can be made by 
turning the frame adjusters on the rigging frame:
The single vertical adjuster at the front left corner is used to 
raise or lower the front of the...

Rev B 02/2007 Page 2.15
Digital Projection TITAN XG-500 User Manual  2. Installation
Notes
 When stacking projectors, 
the stack MUST be vertical, 
to ensure that the stresses 
are distributed to all frame 
couplings.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector is 
capable of supporting the 
combined weight of all the 
projectors and lenses (see 
specifi cation for weights).
 Do not place heavy objects 
on top of the projector 
chassis. Only the chassis 
corners and...

Page 2.16 Rev B 02/2007
2. Installation  Digital Projection TITAN XG-500 User Manual
Notes
  For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
  Input 4. is not used on this 
projector.
  For more information about pin 
connections and control codes 
see section 7. Appendix.
  For more information on 
input modes see section 
4. Overview.
Connecting the projector
Signal Inputs
The following inputs are available:
EDID handshaking...

Rev B 02/2007 Page 2.17
Digital Projection TITAN XG-500 User Manual  2. Installation
Notes
  For more information about pin 
connections and control codes 
see section 7. Appendix.
  For more information about 
using a browser to control the 
projector see section 4. Using 
the menus.
ComputerNull-modem  
cableTITAN
Control connection examples
LAN connection
All of the projector’s features can be controlled via a LAN connection, using a 
standard internet browser package such as Internet Explorer.
RS232...

Page 2.18 Rev B 02/2007
2. Installation  Digital Projection TITAN XG-500 User Manual
Notes
  Use only the power cable 
provided.
  Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
  Handle the power cable 
carefully and avoid sharp 
bends. Do not use a damaged 
power cable.
Power connection
When mains power is fi rst applied, the projector will perform a self-test, then go into 
Standby mode.
The Power indicator on the control panel will show amber until the...

Rev B 02/2007  Page 3.1
3. Getting Started
Contents
Switching the projector on ............................................................................................................... 3.2
Selecting an input or test pattern ................................................................................................... 3.2
Input ................................................................................................................................................ 3.2
Test pattern...

Page 3.2 Rev B 02/2007
3. Getting Started  Digital Projection TITAN XG-500 User Manual
Selecting an input or test pattern
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. (not used in this projector)
5. Composite Video
6. S-Video
7. Component
Or press the numbered keys 1–7 to change directly to the input:
Test pattern
 If you have no video source connected to the projector, then you can display a test 
pattern as follows:
Press 
 on the remote...