Digital Projection Titan Xg-500 User Manual

Rev B 02/2007 Page 4.29
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
 The Trim submenu is available  
only if Global Colour Mode is 
selected.
Colour Menu
 Trim
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
Trim
Press  and   to select Trim.
 Press 
 to open the Trim submenu.
Trim RGB Lift and Gain
Press  and   to select the parameter to be adjusted.
 Press 
 and   to adjust the slider (-128...

Page 4.30 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Setup Menu
Setup menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Setup is highlighted.
Press 
 to open the Setup menu. The blue highlight moves to the fi rst item in 
the menu. • 

Rev B 02/2007 Page 4.31
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Projector
Press  and   to select Projector.
 Press 
 to open the Projector submenu.
Orientation
Press  and   to select Orientation.
 Press 
 and   to select from:
Desktop Front
Desktop Rear
Ceiling Front
Ceiling Rear
Control Panel Backlight
Press  and   to select Backlight.
 Press 
 and   to select from:
On
Off
Component Video Sync
Press  and   to select Component Video Sync.
 Press 
 and   to select from:...

Page 4.32 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Keystone
Used to correct for distortion caused by the projector being mounted higher or lower 
than the screen.
Press 
 and   to select Keystone.
 Press 
 and   to adjust the slider (-128 to +127).
Test Pattern
Press  and   to select Test Pattern.
 Press 
 to open the Test Pattern submenu.
 Press 
 and   to select from:
Off
Alignment Grid
Screen Layout    (shows outlines of various aspect ratios)...

Rev B 02/2007 Page 4.33
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
Setup Menu
 Global Colourimetry
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in 
the Colour menus.
Global Colourimetry
Press  and   to select Global Colourimetry.
Press 
 to open the Global Colourimetry submenu. •
•
Setup menu...

Page 4.34 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
 The Colour Temperature 
slider is available  only if 
Temperature Mode is selected.
 The RGB Lift and Gain sliders 
are available  only if User Mode 
is selected.
Colour Mode
Press  and   to select Colour Mode.
 Press 
 and   to select from:
Temperature
User
Peak
Colour...

Rev B 02/2007 Page 4.35
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Lamp
Press  and   to select Lamp.
 Press 
 to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press  and   to select Change Lamp Setting.
Press 
 to open the Lamp Setting control box. •
•
Notes
Setup Menu
 Lamp Setup menu, continued
continued 

Page 4.36 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  In single lamp modes:
  - if the running lamp fails, the 
other lamp will automatically be 
switched on.
  The selected lamp mode:
  - will not be applied until OK is 
selected
  - will be applied gradually over a 
period of 30 seconds
  - will not be applied until the end 
of any warm-up or cool-down 
period that has already started.
Lamp Power
Press  and   to select the Lamp Power setting.
 Press...

Rev B 02/2007 Page 4.37
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
Setup Menu
  On Screen Display
 The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
 (see Geometry menu, earlier in 
this section).
  If a menu is opened, and no 
other key is pressed within the 
period set in the OSD Timeout 
menu, then the menus will 
disappear. When the  
 key 
is pressed again, the menus will 
reopen at the same point they 
were last viewed.
On...

Page 4.38 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Password
Entry to the password protected area is available to authorised service personel 
only.
Press 
 and   to select Password.
 Press 
 to open the Password control box.
Press 
 and   to select each digit in turn.
 Press 
 and   to adjust the digit from:
0 to 9
 then move to the next digit.
 Use 
 and   to select from
OK
 Press   
 to enter the password controlled area.
or Cancel
Press  
 or   to exit...