Digital Projection Titan Xg-500 User Manual

							Rev B 02/2007 Page 4.19
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
Input Menu
 Presets
Input Menu
 Presets
    Recall Presets A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters 
saved for each Preset are:
all settings from the Picture menu,
all settings from the Input menu (1 – 7)
all settings from the Geometry menu, except Keystone
all settings from the Colour menu, except Global
Press 
 and   to select Presets. 
 Press 
 to open the Presets submenu.
Recall Presets
Press  and   to select Recall Preset.
 Press 
 to open the Recal Presets A ~ H submenu. Any presets that have 
been saved are indicated by their description, for example D: in this example.
To recall a set of parameters that has been saved, press 
 and   to select 
one of the Presets.
 For Presets J to S, select Recall Preset J ~ S then press 
 to open the 
J~S submenu. Press 
 and   to select the Preset.
 Press 
 to confi rm your selection.
 The Preset parameters will be loaded. •
•
•
•
Input menu continued 
						

							Page 4.20 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
Input Menu
 Presets
    Save Presets A ~ H Save Presets
Press  and   to select Save Preset.
 Press 
 to open the Save Presets A ~ H submenu.
To save the current set of parameters, press 
 and   to select one of the 
Presets.
 For Presets J to S, select Save Preset J ~ S then press 
 to open the 
J~S submenu. Press 
 and   to select the Preset.
 Press 
 to confi rm your selection.
 If this Preset has been used before, but only if the Input source has been 
changed, then the following  message will be displayed.
 Press 
 and   to select either OK or Cancel.
 Press 
 to confi rm your selection.
 The parameters will be saved to the selected preset, and the following message 
will be displayed. •
•
Input menu continued 
						

							Rev B 02/2007 Page 4.21
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Picture Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is 
available for Composite, S-
Video and Component inputs 
only.
 The Hue slider is available for 
NTSC inputs only.
Picture menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Picture is highlighted.
Press 
 to open the Picture menu. The blue highlight moves to the fi rst item in 
the menu.
Brightness
Press  and   to select Brightness.
 Press 
 and   to adjust the slider (-128 to +127).
Contrast
Press  and   to select Contrast.
 Press 
 and   to adjust the slider (-128 to +127).
Saturation
Adjusts the saturation at white peak levels.
Press 
 and   to select Saturation.
 Press 
 and   to adjust the slider (0 to 255).
Hue
Adjusts the color balance from green to blue, using the red level as a reference.
Press 
 and   to select Hue.
 Press 
 and   to adjust the slider (0 to 255). •
•
•
•
• 
						

							Page 4.22 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  For more information about 
User gamma settings, see 
section 5. DP Userware.
 Parametric Gamma adjustment 
is available only when 
Parametric is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for graphics based 
RGB sources only.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied. The 
projector’s gamma adjustment can be used to correct for this.
Press 
 and   to select Gamma.
 Press 
 and   to select from:
Parametric  Enables the gamma slider
User download  Applies the gamma settings made externally using the DP 
Userware on a personal computer
Graphics  To be defi ned.
NTSC  NTSC colour space, with a gamma of 2.2
PA L  PAL colour space, with a gamma of 2.2
Punch  Enhanced brightness and increased colour saturation for high 
ambient environments.
Parametric Gamma
Press  and   to select Parametric Gamma.
 Press 
 and   to adjust the slider (1.0 to 3.0 in 0.1 steps).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to 
correct for shimmering or poor quality defi nition on, for example, fi ne text.
Press 
 and   to select Phase.
 Press 
 and   to adjust the slider (0 to 31). •
•
•
Picture menu continued 
						

							Rev B 02/2007 Page 4.23
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings made in 
the Geometry menu.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio.
 Press 
 and   to select from:
Fill  This will best fi t the incoming source to fi ll either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.25:1 (5:4)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Native  The image will be displayed pixel for pixel. The image will 
be centred, with a black border if smaller than 1280 x 720 or 
cropped if larger.
Sharpness
Press  and   to select Sharpness.
 Press 
 and   to adjust the slider. •
•
Picture menu continued 
						

							Page 4.24 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Geometry Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings (see 
next page).
Geometry menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Geometry is highlighted.
Press 
 to open the Geometry menu. The blue highlight moves to the fi rst item 
in the menu.
Horizontal Position
Press  and   to select H Position.
 Press 
 and   to adjust the slider.
Vertical Position
Press  and   to select V Position.
 Press 
 and   to adjust the slider.
Aspect Ratio
 Press  and   to select from:
Fill  This will best fi t the incoming source to fi ll either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.25:1 (5:4)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Native  The image will be displayed pixel for pixel. The image will 
be centred, with a black border if smaller than 1280 x 720 or 
cropped if larger. •
•
•
• 
						

							Rev B 02/2007 Page 4.25
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
 Horizontal and Vertical 
Aspect Ratio adjustments are 
available only when User is 
selected in Aspect Ratio, (see 
previous page).
 Keystone adjustment can be 
found in both the Geometry and 
Projector Setup menus.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for graphics based 
RGB sources only.
 Pixels adjustment  is available 
for graphics based RGB inputs 
only.
User Horizontal Aspect Ratio
Press  and   to select User H Aspect.
 Press 
 and   to adjust the slider (internal number – adjust to fi t).
User Vertical Aspect Ratio
Press  and   to select User V Aspect.
 Press 
 and   to adjust the slider (internal number – adjust to fi t).
Keystone
Used to correct for distortion caused by the projector being mounted higher or lower 
than the screen.
Press 
 and   to select Keystone.
 Press 
 and   to adjust the slider (-128 to +127).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to 
correct for shimmering or poor quality defi nition on, for example, fi ne text.
Press 
 and   to select Phase.
 Press 
 and   to adjust the slider (0 to 32).
Pixels per line
Pixels per line should be set automatically by the projector, but can be adjusted 
manually to correct for non-standard sources.
Press 
 and   to select Pixels.
 Press 
 and   to adjust the slider. •
•
•
•
•
Geometry menu continued 
						

							Page 4.26 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Blanking
Blanking curtains can be applied to each edge of the picture.
Press 
 and   to select Blanking.
 Press 
 to open the Blanking submenu.
Blanking On/Off
 Press  and   to select from:
On
Off
Blanking adjust
Press  and   to select the edge to be Blanked.
 Press 
 and   to adjust the slider (0 to 200). •
•
•
Notes
Geometry Menu
 Blanking
  The blanking curtains will not 
applied until Blanking is turned 
On.
 The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
  Set to zero for no blanking, eg 
the top edge in this example.
Geometry menu continued 
						

							Rev B 02/2007 Page 4.27
Digital Projection TITAN XG-500 User Manual  4. Controlling the projector
Notes
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Colour Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in 
the Colour menus.
Colour menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Colour is highlighted.
Press 
 to open the Colour menu. The blue highlight moves to the fi rst item in 
the menu. •
  Notes on Colour and Global Colourimetry
Global Colourimetry menu (see later in this section, in Setup menu)
After a calibration check on the projector or venue, a set of Global colour settings 
can be made in the Global Colourimetry menu. These settings are then available 
to be copied at any time using the Colour Mode setting in the Colour menu, or 
used as a starting point using the Trim feature in the Colour menu.
Colour menu (see this section).
The settings made in the Colour menu will be automatically saved in the Mode 
History, or can be manually saved to one of the Input Presets (see Input modes 
and settings earlier in this section).
The selections available in Colour Mode in the Colour menu are:
Global  Copies the settings made in the Global Colourimetry menu
Temperature  Set the colour temperature using the slider
User  Set the Red, Green and Blue Lift and Gain using the sliders
Peak  Preset high brightness setting 
						

							Page 4.28 Rev B 02/2007
4. Controlling the projector  Digital Projection TITAN XG-500 User Manual
Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
 The Colour Temperature 
slider is available  only if 
Temperature Mode is selected.
 The RGB Lift and Gain sliders 
are available  only if User Mode 
is selected.
 The Component Type selection 
is available  for RGB1, RGB2 
and Component inputs only.
Colour Mode
Press  and   to select Colour Mode.
 Press 
 and   to select from:
Global
Temperature
User
Peak
Colour Temperature
Press  and   to select Temperature.
 Press 
 and   to adjust the slider (3,000K to 10,000K. in 100 steps).
RGB Lift
Press  and   to select the parameter to be adjusted.
 Press 
 and   to adjust the slider.
RGB Gain
Press  and   to select the parameter to be adjusted.
 Press 
 and   to adjust the slider.
Component Type
Press  and   to select Component Type.
 Press 
 and   to select from:
RGB
YPrPb •
•
•
•
•
Colour menu continued