Digital Projection Titan Sx+-500 User Manual

Rev B          02/2007        page 4.29
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
The Trim submenu is available
only if Global Colour Mode is
selected.
Colour Menu
Trim
Read the notes on Colour and
Global Colourimetry earlier in
this section before making
any settings in the Colour
menus.
Trim
•Press  and   to select Trim.
Press 
 to open the Trim submenu.
Trim RGB Lift and Gain
•Press  and   to select the parameter to be adjusted.
Press 
 and   to adjust the slider...

Rev B          02/2007         page 4.30
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
When using the menus, press
OSD 
 or  to hide or
reveal the On-Screen-Display.
Setup Menu
Setup menu
To return to the main menu, press  up to three times.
From the main menu:
•Press 
 and   until Setup is highlighted.
Press 
 to open the Setup menu. The blue highlight moves to the first item in
the menu. 

Rev B          02/2007        page 4.31
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Projector
•Press  and   to select Projector.
Press 
 to open the Projector submenu.
Orientation
•Press  and   to select Orientation.
Press 
 and   to select from:
Desktop Front
Desktop Rear
Ceiling Front
Ceiling Rear
Control Panel Backlight
•Press  and   to select Backlight.
Press 
 and   to select from:
On
Off
Component Video Sync
•Press  and   to select Component Video Sync.
Press 
 and...

Rev B          02/2007         page 4.32
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Keystone
Used to correct for distortion caused by the projector being mounted higher or lower
than the screen.
•Press 
 and   to select Keystone.
Press 
 and   to adjust the slider (-128 to +127).
Test Pattern
•Press  and   to select Test Pattern.
Press 
 to open the Test Pattern submenu.
Press 
 and   to select from:
Off
Alignment Grid
Screen Layout(shows outlines of various aspect ratios)...

Rev B          02/2007        page 4.33
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Setup Menu
Global Colourimetry
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Read these notes on Colour
and Global Colourimetry
before making any settings in
the Colour menus.
Global Colourimetry
•Press  and   to select Global Colourimetry.
Press 
 to open the Global Colourimetry submenu.
Setup menu...

Rev B          02/2007         page 4.34
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
Read the notes on Colour and
Global Colourimetry earlier in
this section before making
any settings in the Colour
menus.
The Colour Temperature slider
is available  only if
Temperature Mode is selected.
The RGB Lift and Gain sliders
are available  only if User Mode
is selected.
Colour Mode
•Press  and   to select Colour Mode.
Press 
 and   to select from:
Temperature
User
Peak
Video...

Rev B          02/2007        page 4.35
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Lamp
•Press  and   to select Lamp.
Press 
 to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
•Press  and   to select Change Lamp Setting.
Press 
 to open the Lamp Setting control box.
Notes
Setup Menu
Lamp Setup menu, continued 

Rev B          02/2007         page 4.36
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
In single lamp modes:
- if the running lamp fails, the
other lamp will automatically be
switched on.
The selected lamp mode:
- will not be applied until OK is
selected
- will be applied gradually over
a period of 30 seconds
- will not be applied until the
end of any warm-up or cool-
down period that has already
started.
Lamp Power
•Press  and   to select the Lamp Power setting.
Press...

Rev B          02/2007        page 4.37
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Setup Menu
On Screen Display
The On Screen Display will
move to the centre of the DMD
when Blanking is turned On.
(see Geometry menu, earlier in
this section).
If a menu is opened, and no
other key is pressed within the
period set in the OSD Timeout
menu, then the menus will
disappear. When the  
 key
is pressed again, the menus will
reopen at the same point they
were last viewed.
On...

Rev B          02/2007         page 4.38
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Password
Entry to the password protected area is available to authorised service personel
only.
•Press 
 and   to select Password.
Press 
 to open the Password control box.
•Press 
 and   to select each digit in turn.
Press 
 and   to adjust the digit from:
0 to 9
then move to the next digit.
Use 
 and   to select from
OK
Press 
 to enter the password controlled area.
or Cancel
Press 
  or...