Digital Projection Titan Sx+-500 User Manual
Have a look at the manual Digital Projection Titan Sx+-500 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Rev B 02/2007 page 4.29 Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector Notes The Trim submenu is available only if Global Colour Mode is selected. Colour Menu Trim Read the notes on Colour and Global Colourimetry earlier in this section before making any settings in the Colour menus. Trim •Press and to select Trim. Press to open the Trim submenu. Trim RGB Lift and Gain •Press and to select the parameter to be adjusted. Press and to adjust the slider (-128 to +127). Global Colourimetry This is a shortcut to the Global Colourimetry submenu, described later in this section, in Setup Menu. •Press and to select Global Colourimetry. Press to open the Global Colourimetry submenu. Colour menu continued
Rev B 02/2007 page 4.30 4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual Notes When using the menus, press OSD or to hide or reveal the On-Screen-Display. Setup Menu Setup menu To return to the main menu, press up to three times. From the main menu: •Press and until Setup is highlighted. Press to open the Setup menu. The blue highlight moves to the first item in the menu.
Rev B 02/2007 page 4.31 Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector Projector •Press and to select Projector. Press to open the Projector submenu. Orientation •Press and to select Orientation. Press and to select from: Desktop Front Desktop Rear Ceiling Front Ceiling Rear Control Panel Backlight •Press and to select Backlight. Press and to select from: On Off Component Video Sync •Press and to select Component Video Sync. Press and to select from: Sync On Green Separate Setup menu, continuedNotes Setup Menu Projector
Rev B 02/2007 page 4.32 4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual Keystone Used to correct for distortion caused by the projector being mounted higher or lower than the screen. •Press and to select Keystone. Press and to adjust the slider (-128 to +127). Test Pattern •Press and to select Test Pattern. Press to open the Test Pattern submenu. Press and to select from: Off Alignment Grid Screen Layout(shows outlines of various aspect ratios) Chequerboard Colour Bars 0% Field(black) 20% Field 100% Field(white, affected by colour settings) 100% Field (Peak White)(white, unaffected by colour settings) Setup menu, Projector continuedNotes
Rev B 02/2007 page 4.33 Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector Notes Setup Menu Global Colourimetry Some menu items may be greyed out - unavailable due to the effect of settings made in other menus, or due to the type of input signal. Read these notes on Colour and Global Colourimetry before making any settings in the Colour menus. Global Colourimetry •Press and to select Global Colourimetry. Press to open the Global Colourimetry submenu. Setup menu continued Notes on Colour and Global Colourimetry Global Colourimetry menu (see this section) A fter a calibration check on the projector or venue, a set of Global colour settings can be made in the Global Colourimetry menu. These settings are then available to be copied at any time using the Colour Mode setting in the Colour menu, or used as a starting point using the Trim feature in the Colour menu. Colour menu (see earlier in this section). The settings made in the Colour menu will be automatically saved in the Mode History, or can be manually saved to one of the Input Presets (see Input modes and settings earlier in this section). The selections available in Colour Mode in the Colour menu are: GlobalCopies the settings made in the Global Colourimetry menu TemperatureSet the colour temperature using the slider UserSet the Red, Green and Blue Lift and Gain using the sliders PeakPreset high brightness setting Video, Film, GraphicApplies the factory set P7 settings User 1, 2Applies the User gamma settings made externally using the DP Userware on a personal computer
Rev B 02/2007 page 4.34 4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual Notes Read the notes on Colour and Global Colourimetry earlier in this section before making any settings in the Colour menus. The Colour Temperature slider is available only if Temperature Mode is selected. The RGB Lift and Gain sliders are available only if User Mode is selected. Colour Mode •Press and to select Colour Mode. Press and to select from: Temperature User Peak Video Film Graphic User 1 User 2 Colour Temperature •Press and to select Temperature. Press and to adjust the slider (3,000K to 10,000K. in 100 steps). RGB Lift •Press and to select the parameter to be adjusted. Press and to adjust the slider. RGB Gain •Press and to select the parameter to be adjusted. Press and to adjust the slider. Setup menu, Global Colourimetry continued
Rev B 02/2007 page 4.35 Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector Lamp •Press and to select Lamp. Press to open the Lamp submenu. The middle row shows the current lamp setting. Change Lamp Setting •Press and to select Change Lamp Setting. Press to open the Lamp Setting control box. Notes Setup Menu Lamp Setup menu, continued
Rev B 02/2007 page 4.36 4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual Notes In single lamp modes: - if the running lamp fails, the other lamp will automatically be switched on. The selected lamp mode: - will not be applied until OK is selected - will be applied gradually over a period of 30 seconds - will not be applied until the end of any warm-up or cool- down period that has already started. Lamp Power •Press and to select the Lamp Power setting. Press and to adjust the Lamp Power from: 80 to 100%in 1% steps Lamp Mode •Press and to select Lamp Mode. Press and to select from: single lamp modes Lamp 1lamp 1 only Lamp 2lamp 2 only Alternateon power up, selects the lamp with the least hours used dual lamp mode Lamps 1 and 2both lamps OK •Press and to select OK. Press to apply the new settings. Cancel •Press and to select Cancel. Press or to exit without applying the new settings. The indicators on the control panel will show as follows: Lamp 1red = LAMP ERRORgreen = ON (100%)amber = ON (80 - 99%) flashing green/amber = lamp cool-down or warm up Lamp 2red = LAMP ERRORgreen = ON (100%)amber = ON (80 - 99%) flashing green/amber = lamp cool-down or warm up Setup menu, Lamp continued
Rev B 02/2007 page 4.37 Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector Notes Setup Menu On Screen Display The On Screen Display will move to the centre of the DMD when Blanking is turned On. (see Geometry menu, earlier in this section). If a menu is opened, and no other key is pressed within the period set in the OSD Timeout menu, then the menus will disappear. When the key is pressed again, the menus will reopen at the same point they were last viewed. On Screen Display •Press and to select On Screen Display. Press to open the On Screen Display submenu. OSD Position •Press and to select OSD Position Press and to select from: Upper Left Upper Centre Upper Right Middle Left Middle Centre Middle Right Lower Left Lower Centre Lower Right OSD Size •Press and to select OSD Size. Press and to select from: Large Small OSD Timeout •Press and to select the length of the On Screen Display Timeout. Press and to select from: 0 to 255in 1 second step s (when set to zero, the OSD never times out) Setup menu continued
Rev B 02/2007 page 4.38 4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual Password Entry to the password protected area is available to authorised service personel only. •Press and to select Password. Press to open the Password control box. •Press and to select each digit in turn. Press and to adjust the digit from: 0 to 9 then move to the next digit. Use and to select from OK Press to enter the password controlled area. or Cancel Press or to exit without applying the password. Notes Setup menu continued