Digital Projection Titan Sx+-500 User Manual

							Rev B          02/2007       page 2.11
Digital Projection TITAN sx+-500 User Manual2. Installation
Notes
For more information on using
the Lens shift feature, see
section 4. Using the menus,
Lens menu.
If the lens is to be shifted in two
directions combined, the
maximum range is somewhat
less, as can be seen below.
full horizontal and vertical shift
without distortion
combined shift without distortion
is reduced
total lens mount shift available
Shifting the image
The normal position for the projector is at the centre of the screen. However, you
can set the projector above or below the centre, or to one side, and adjust the image
using the Lens shift feature to maintain a geometrically correct image.
•Any single adjustment outside the ranges specified below may result in an
unacceptable level of distortion, paricularly at the corners of the image, due to
the image passing through the periphery of the lens optics.
•If the lens is to be shifted in two directions combined, the maximum range
without distortion will be somewhat less, as can be seen in the diagrams to the
right.
The maximum range available with no distortion is dependent on which lens is used.
The tables below show the maximum range for images that fill the DMD. For images
which do not use the full height or width, extra shift will be possible, up to the limit of
the lens mount movement.
0.73 : 1 fixed lens105-607
1.21 : 1 fixed lenses105-608 and 105-609
zoom lenses105-610 to 105-613
It is physically possible to shift the lens further than this, up to the number of pixels
shown in the diagram to the right. However:
•There will be some distortion of the image beyond the ranges specified above.
•Due to continuing product development, these figures may vary by ±25 pixels.
verticalhorizontalverticalhorizontal
(pixels) (pixels) (vs DMD height) (vs DMD width)
± 120 ± 95 ± 0.11 H ± 0.07W
700
(0.5W)700
(0.5W)
525
(0.5H)
525
(0.5H)
verticalhorizontalverticalhorizontal
(pixels) (pixels) (vs DMD height) (vs DMD width)
± 525 ± 450 ± 0.5H ± 0.32W 
						

							Rev B          02/2007      page 2.12
2. InstallationDigital Projection TITAN sx+-500 User Manual
Notes
BEFORE INSTALLING THE
PROJECTOR, READ ALL THE
WARNINGS BELOW AND ALL
THOSE IN IMPORTANT
INFORMATION AT THE
FRONT OF THIS MANUAL.
The projector weighs
approximately 27kg (60lbs).
Use safe handling techniques
when lifting the projector.
Make sure that the surface,
ceiling or rigging that is to
support the projector is
capable of supporting the
combined weight of the
projector and lens (see
specification for weights ).
Backup safety chains or
wires should always be used.
Do not tilt the projector more
than  ±12° from side to side
when in use, as this may
cause serious lamp failure,
damage the lamp module and
cause extra cost on
replacement. The projector
my be tilted forwards and
backwards as necessary.
±12°
360°
Mounting the pr ojector
The projector is designed to be used on a flat surface, but the optional rigging frame
will allow it to be suspended from a lighting truss or rigging. The four adjustable feet
under the chassis allow the projector to be lowered onto a flat surface without any
danger of hands being trapped between the bottom frame and the surface.
Chassis adjustment
If the projector is to be operated from a flat surface such as a projector table, then
adjustment of projector level should be made by turning the four feet under the
chassis.
If the projector is to be operated from a flat surface such as a projector table, then
adjustment of projector level should be made by turning the four feet under the
chassis.
Fitting the optional rigging frame
•The  rigging frame should be secured to the projector using the twelve screws
supplied, as shown in the pictures below. Four screws secure each of the threee
adjuster brackets to its corner post. Fit the screws to the round holes first, then fit
the screws to the oval holes.
•Before suspending the projector, make sure that all the frame adjusters are set
roughly midway.
Adjustable
foot
Fixing
screws 
						

							Rev B          02/2007       page 2.13
Digital Projection TITAN sx+-500 User Manual2. Installation
Adjusting the rigging frame
Coarse adjustment of projector level should be made by adjusting the length of the
supporting wires or chains, or by adjusting the position of the truss or rigging. Once
the initial coarse adjustment has been made, fine adjustment can be made by
turning the frame adjusters on the rigging frame:
•The single vertical adjuster at the front left corner is used to
raise or lower the front of the projector (pitch adjustment).
•The two vertical adjusters at the rear are used to rotate the
projector around the lens axis (roll adjustment).
•The horizontal adjuster at the rear right corner (viewed from the
front) is used to rotate the projector around it s vertical axis (yaw
adjustment).
Notes
BEFORE INSTALLING THE
PROJECTOR, READ ALL THE
WARNINGS BELOW AND ALL
THOSE IN IMPOR TANT
INFORMATION AT THE
FRONT OF THIS MANUAL.
The projector weighs
approximately 27kg (60lbs).
Use safe handling techniques
when lifting the projector.
Make sure that the surface,
ceiling or rigging that is to
support the projector is
capable of supporting the
combined weight of the
projector and lens (see
specification for weights ).
Backup safety chains or
wires should always be used.
Do not tilt the projector more
than  ±12° from side to side
when in use, as this may
cause serious lamp failure,
damage the lamp module and
cause extra cost on
replacement. The projector
my be tilted forwards and
backwards as necessary.
±12°
360°
Vertical
adjuster
Horizontal
adjuster 
						

							Rev B          02/2007      page 2.14
2. InstallationDigital Projection TITAN sx+-500 User Manual
Notes
When stacking projectors, the
stack MUST be vertical, to
ensure that the stresses are
distributed to all frame
couplings.
Make sure that the surface,
ceiling or rigging that is to
support the projector is
capable of supporting the
combined weight of all the
projectors and lenses (see
specification for weights ).
Do not place heavy objects
on top of the projector
chassis. Only the chassis
corners and the rigging frame
are capable of withstanding
the weight of another
projector.
Do not try to stack more than
3 projectors.
Separate backup safety
chains or wires should
always be used for each
projector.
Stacking pr ojectors
The rigging frame is capable of supporting the weight of up to two other projectors,
using the built-in frame couplings. The projectors can be stacked on top of each
other, or suspended below each other.
•Carefully lower each projector down onto the top of the others, making sure that
all four frame couplings engage fully.
•Fit a locking pin into each coupling. A ball in the end of the pin prevents the pin
from falling out – to insert or remove a locking pin, press the button on the t-bar
to release the ball.
•Align the images from the projectors, following the instructions in section
3. Getting started, Adjusting the lens and Adjusting the projected image. Frame
couplingsLocking
pin 
						

							Rev B          02/2007       page 2.15
Digital Projection TITAN sx+-500 User Manual2. Installation
Notes
For more information on
selecting an input source, see
section 4. Overview, Using
the control keys, and Using
the menus.
For more information about pin
connections and control codes
see section 7. Appendix.
For more information on input
modes see section
4. Overview.
Input
connection panelControl
connection panel
Connecting the projector
Signal Inputs
The following inputs are available:
EDID handshaking on the DVI and RGB2 inputs
If you are using a computer DVI card or other source that obeys the EDID
handshaking protocol, then the card or source will automatically configure itself to
suit the projector.
If not, then you should refer to the documentation supplied with the source to
manually set the resolution to 1400 x 1050 or the nearest suitable setting. Switch off
the source, connect to the projector, then switch the source back on again.
5. Composite Video
6. S-Video 7. Component 1. RGB12. RGB2 4. SDI3. DVI 
						

							Rev B          02/2007      page 2.16
2. InstallationDigital Projection TITAN sx+-500 User Manual
Notes
For more information about pin
connections and control codes
see section 7. Appendix.
For more information about
using a browser to control the
projector see section 4. Using
the menus.Crossed
LAN cableTITAN
Computer
Un-crossed
LAN cablesComputer
TITAN TITAN Hub or
LAN
ComputerNull-modem
cableTITAN
Control connection examples
LAN connection
All of the projector’s features can be controlled via a LAN connection, using a
standard internet browser package such as Internet Explorer.
RS232 connection 
						

							Rev B          02/2007       page 2.17
Digital Projection TITAN sx+-500 User Manual2. Installation
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a Ground
connection, as this
equipment MUST be earthed.
Handle the power cable
carefully and avoid sharp
bends. Do not use a damaged
power cable.
Power connection
When mains power is first applied, the projector will perform a self-test, then go into
Standby mode.
The Power indicator on the control panel will show amber until the  POWER 
on the remote control or the keypad,  is pressed for 3 seconds.
Power connection 
						

							Rev B          02/2007      page 2.18
2. InstallationDigital Projection TITAN sx+-500 User Manual 
						

							Rev B          02/2007
3. Getting started
Contents
3. Getting started 3.1
Switching the projector on .....................................................................................................3.2
Selecting an input or test pattern.......................................................................................... 3.2
Input................................................................................................................................................................. 3.2
Adjusting the lens ................................................................................................................... 3.3
Focus................................................................................................................................................................ 3.3
Zoom................................................................................................................................................................ 3.3
Shift .................................................................................................................................................................. 3.3
Adjusting the projected image ............................................................................................... 3.4
Picture settings............................................................................................................................................... 3.4
Geometry settings........................................................................................................................................... 3.4
Switching the projector off ..................................................................................................... 3.4 
						

							Rev B          02/2007         page 3.2 3. Getting startedDigital Projection 
TITAN sx+-500 User Manual
Selecting an input or test patter n
Input
•Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
•Or press the numbered keys 1–7 to change directly to the input:
If you have no video source connected to the projector, then you can display a test
pattern as follows:
•Press 
 on the remote control, to select a test pattern.
Switching the projector on
•Connect the power cable between the mains supply and the projector.
W ait until the self-test has completed and the power indicator on the control
panel shows amber. The lamp will be off, the shutter closed, and the projector
will be in STANDBY mode.
•Press POWER 
 on the remote control or the keyp ad, and hold for about 3
seconds to switch the projector ON. The power indicator on the control panel will
show green, the lamp will light and the shutter will open.
Notes
For more information about
connecting the power cable,
see Power Connections, in
Section 2. Installation.
For more detailed information
about:
- using the control keys on the
remote control or keypad,
- using the menus,
see the next section:
Controlling the projector.
Power connection