Digital Projection Titan Sx+-500 User Manual

							Rev B          02/2007        page 4.19
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
For more information about
input modes and input presets,
see earlier in this section, Input
modes and settings.
Input Menu
Presets
Input Menu
Presets
Recall Preset s A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters
saved for each Preset are:
all settings from the Picture menu,
all settings from the Input menu (1 – 7)
all settings from the Geometry menu, except Keystone
all settings from the Colour menu, except Global
•Press 
 and   to select Presets.
Press 
 to open the Presets submenu.
Recall Presets
•Press  and   to select Recall Preset.
Press 
 to open the Recal Presets A ~ H submenu. Any presets that have
been saved are indicated by their description, for example D: in this example.
•To recall a set of parameters that has been saved, press 
 and   to select
one of the Presets.
For Presets J to S, select Recall Preset J ~ S then press 
 to open the
J~S submenu. Press 
 and   to select the Preset.
Press 
 to confirm your selection.
The Preset parameters will be loaded.
Input menu continued 
						

							Rev B          02/2007         page 4.20
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
Input Menu
Presets
Save Presets A ~ H Save Presets
•Press  and   to select Save Preset.
Press 
 to open the Save Presets A  ~ H submenu.
• To save the current set of parameters, press 
 and   to select one of the
Presets.
For Presets J to S, select Save Preset J ~ S then press 
 to open the
J~S submenu. Press 
 and   to select the Preset.
Press 
 to confirm your selection.
If this Preset has been used before, but only if the Input source has been
changed, then the following  message will be displayed.
Press 
 and   to select either OK or Cancel.
Press 
 to confirm your selection.
The parameters will be saved to the selected preset, and the following message
will be displayed.
Input menu continued 
						

							Rev B          02/2007        page 4.21
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When using the menus, press
OSD 
 or  to hide or
reveal the On-Screen-Display.
Picture Menu
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
The Saturation slider is
available for Composite, S-
Video and Component input s
only.
The Hue slider is available for
NTSC inputs only.
Picture menu
To return to the main menu, press  up to three times.
From the main menu:
•Press 
 and   until Picture is highlighted.
Press 
 to open the Picture menu. The blue highlight moves to the first item in
the menu.
Brightness
•Press  and   to select Brightness.
Press 
 and   to adjust the slider (-128 to +127).
Contrast
•Press  and   to select Contrast.
Press 
 and   to adjust the slider (-128 to +127).
Saturation
Adjusts the saturation at white peak levels.
•Press 
 and   to select Saturation.
Press 
 and   to adjust the slider (0 to 255).
Hue
Adjusts the color balance from green to blue, using the red level as a reference.
•Press 
 and   to select Hue.
Press 
 and   to adjust the slider (0 to 255). 
						

							Rev B          02/2007         page 4.22
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
For more information about
User gamma settings, see
Section 5. DP Userware.
Parametric Gamma adjustment
is available only when
Parametric is selected in
Gamma selection, above.
Phase adjustment can be found
in both the Picture and
Geometry menus, and is
available for graphics based
RGB sources only.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied. The
projector ’s gamma adjustment can be used to correct for this.
•Press 
 and   to select Gamma.
Press 
 and   to select from:
ParametricEnables the gamma slider
User downloadApplies the gamma settings made externally using the DP
Userware on a personal computer
GraphicsTo be defined.
NTSCNTSC colour sp ace, with a gamma of 2.2
PALPAL colour space, with a gamma of 2.2
PunchEnhanced brightness and increased colour saturation for high
ambient environments.
Parametric Gamma
•Press  and   to select Parametric Gamma.
Press 
 and   to adjust the slider (1.0 to 3.0 in 0.1 steps).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to
correct for shimmering or poor quality definition on, for example, fine text.
•Press 
 and   to select Phase.
Press 
 and   to adjust the slider (0 to 31).
Picture menu continued 
						

							Rev B          02/2007        page 4.23
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Aspect Ratio selection can be
found in both the Picture and
Geometry menus.
When User Aspect is selected,
the Aspect Ratio needs to be
set in the Geometry menu.
The Sharpness slider is
available for Composite, S-
Video and Component SD
inputs only.
Aspect Ratio
•Press  and   to select Aspect Ratio.
Press 
 and   to select from:
FillThis will best fit the incoming source to fill either the height or
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.25:1 (5:4)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
NativeThe image will be displayed pixel for pixel. The image will be
centred, with a black border if smaller than 1400 x 1050 or
cropped if larger.
Sharpness
•Press  and   to select Sharpness.
Press 
 and   to adjust the slider.
Picture menu continued 
						

							Rev B          02/2007         page 4.24
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When using the menus, press
OSD 
 or  to hide or
reveal the On-Screen-Display.
Geometry Menu
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Aspect Ratio selection can be
found in both the Picture and
Geometry menus.
When User is selected, the
Aspect Ratio needs to be set in
the User H Aspect and V
Aspect (see next page).
Geometr y menu
To return to the main menu, press  up to three times.
From the main menu:
•Press 
 and   until Geometry is highlighted.
Press 
 to open the Geometry menu. The blue highlight moves to the first
item in the menu.
Horizontal Position
•Press  and   to select H Position.
Press 
 and   to adjust the slider.
Vertical Position
•Press  and   to select V Position.
Press 
 and   to adjust the slider.
Aspect Ratio
Press  and   to select from:
FillThis will best fit the incoming source to fill either the height or
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.25:1 (5:4)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
NativeThe image will be displayed pixel for pixel. The image will be
centred, with a black border if smaller than 1400 x 1050 or
cropped if larger. 
						

							Rev B          02/2007        page 4.25
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Horizontal and Vertical
Aspect Ratio adjustments are
available only when User is
selected in Aspect Ratio, (see
previous page).
Keystone adjustment can be
found in both the Geometry and
Projector Setup menus.
Phase adjustment can be found
in both the Picture and
Geometry menus, and is
available for graphics based
RGB sources only.
Pixels adjustment  is available
for graphics based RGB inputs
only.
User Horizontal Aspect Ratio
•Press  and   to select User H Aspect.
Press 
 and   to adjust the slider (internal number – adjust to fit).
User Vertical Aspect Ratio
•Press  and   to select User V Aspect.
Press 
 and   to adjust the slider (internal number – adjust to fit).
Keystone
Used to correct for distortion caused by the projector being mounted higher or lower
than the screen.
•Press 
 and   to select Keystone.
Press 
 and   to adjust the slider (-128 to +127).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to
correct for shimmering or poor quality definition on, for example, fine text.
•Press 
 and   to select Phase.
Press 
 and   to adjust the slider (0 to 32).
Pixels per line
Pixels per line should be set automatically by the projector, but can be adjusted
manually to correct for non-standard sources.
•Press 
 and   to select Pixels.
Press 
 and   to adjust the slider.
Geometry menu continued 
						

							Rev B          02/2007         page 4.26
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Blanking
Blanking curtains can be applied to each edge of the picture.
•Press 
 and   to select Blanking.
Press 
 to open the Blanking submenu.
Blanking On/Off
Press  and   to select from:
On
Off
Blanking adjust
•Press  and   to select the edge to be Blanked.
Press 
 and   to adjust the slider (0 to 200).
Notes
Geometry Menu
Blanking
The blanking curtains will not
applied until Blanking is turned
On.
The On Screen Display will
move to the centre of the DMD
when Blanking is turned On.
Set to zero for no blanking, eg
the top edge in this example.
Geometry menu continued 
						

							Rev B          02/2007        page 4.27
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
When using the menus, press
OSD 
 or  to hide or
reveal the On-Screen-Display.
Colour Menu
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Read these notes on Colour
and Global Colourimetry
before making any settings in
the Colour menus.
Colour menu
To return to the main menu, press  up to three times.
From the main menu:
•Press 
 and   until Colour is highlighted.
Press 
 to open the Colour menu. The blue highlight moves to the first item in
the menu.
Notes on Colour and Global Colourimetry
Global Colourimetry menu (see later in this section, in Setup menu)
A fter a calibration check on the projector or venue, a set of Global colour settings
can be made in the Global Colourimetry menu. These settings are then available
to be copied at any time using the Colour Mode setting in the Colour menu, or
used as a starting point using the Trim feature in the Colour menu.
Colour menu (see this section).
The settings made in the Colour menu will be automatically saved in the Mode
History, or can be manually saved to one of the Input Presets (see Input modes
and settings earlier in this section).
The selections available in Colour Mode in the Colour menu are:
GlobalCopies the settings made in the Global Colourimetry menu
TemperatureSet the colour temperature using the slider
UserSet the Red, Green and Blue Lift and Gain using the sliders
PeakPreset high brightness setting
Video, Film,
GraphicApplies the factory set P7 settings.
User 1, 2Applies the User gamma settings made externally using the
DP Userware on a personal computer 
						

							Rev B          02/2007         page 4.28
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
Read the notes on Colour and
Global Colourimetry earlier in
this section before making
any settings in the Colour
menus.
The Colour Temperature slider
is available  only if
Temperature Mode is selected.
The RGB Lift and Gain sliders
are available  only if User Mode
is selected.
The Component Type
selection is available  for RGB1,
RGB2 and Component  inputs
only.
Colour Mode
•Press  and   to select Colour Mode.
Press 
 and   to select from:
Global
Temperature
User
Peak
Video
Film
Graphic
User 1
User 2
Colour Temperature
•Press  and   to select Temperature.
Press 
 and   to adjust the slider (3,000K to 10,000K. in 100 steps).
RGB Lift
•Press  and   to select the parameter to be adjusted.
Press 
 and   to adjust the slider.
RGB Gain
•Press  and   to select the parameter to be adjusted.
Press 
 and   to adjust the slider.
Component Type
•Press  and   to select Component Type.
Press 
 and   to select from:
RGB
YPrPb
Colour menu continued