Digital Projection Titan Sx+-500 User Manual

Rev B          02/2007         page 3.3 Digital Projection 
TITAN sx+-500 User Manual 3. Getting started
Notes
For more detailed information
about:
- using the control keys on the
remote control or keypad,
- using the menus,
see the next section:
Controlling the projector.
When any of the three Lens
adjustment keys is pressed, the
blue Transmit indicator will light
for 10 seconds:
- after 10 seconds, if no
adjustment has been made, the
indicator will go out and the
Lens adjustment key must be
pressed...

Rev B          02/2007        page 3.4 3. Getting startedDigital Projection 
TITAN sx+-500 User Manual
Adjusting the projected image
Picture settings
•Press a  key, followed by  and   to adjust these picture settings:
Brightness
 BRI
Contrast
 CON
Saturation
 SAT
Phase
 PHASE
Aspect ratio
 ASPECT
Geometry settings
•Press Keystone KEYST
followed by 
 and  to adjust the keystone correction.
•Press Position
 POS(for all inputs except DVI)
followed by 
, ,  and  to adjust the picture position, for images...

Rev B          02/2007
4. Controlling the projector
continued
Contents
4. Controlling the projector 4.1
Overview.................................................................................................................................. 4.4
Controlling the projector................................................................................................................................ 4.4
Input modes and...

Rev B          02/2007         page 4.2
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
continued
Using the menus ................................................................................................................... 4.15
Navigating menus and submenus ...............................................................................................................4.15
Menu...

Rev B          02/2007        page 4.3
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Setup menu............................................................................................................................4.30
Projector ........................................................................................................................................................4.31...

Rev B          02/2007         page 4.4
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Over view
Controlling the projector
The projector can be controlled from:
•the remote control
•the keypad
•the RS232 input
•the Ethernet input
For more information about controlling the projector using the RS232 and
Ethernet inputs, see Remote communications protocol in section 7.
Appendix.
For information about how to connect the projector, see Connecting the
projector in section 2....

Rev B          02/2007        page 4.5
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Input modes and settings
Input mode detection
The projector can automatically detect the following parameters from the incoming
video signal:
•line frequency
•frame rate
•interlace / progressive
From these parameters the projector can determine input mode, for example:
input source horizontal vertical    mode
•composite15.7KHz50.0Hz = NTSC
•RGB131.5KHz 60.0Hz = SDTV 480p
•SDI 33.8KHz 30.0Hz =...

Rev B          02/2007         page 4.6
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Any subsequent changes that you make to the modal settings will be saved in the
mode history,  with the input mode.
If a new signal is detected, the mode history for the previous signal will be saved in
the mode history, and the new mode added, along with a new set of default settings.
Thus the projector builds up a history of input modes, and the required settings for
each mode, depending on...

Rev B          02/2007        page 4.7
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Indicator s
Input status indicators
The indicator next to each input connector on the input panel will light as follows:
off = input not selected
green = input selected, signal detected and in range
flashing green  = input selected, but signal not detected or out of range
Notes
There are more indicators on
the Control panel, and these are
described on the next page.
5. Composite V ideo6....

Rev B          02/2007         page 4.8
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
The contr ol panel
Keypad layout
The controls on the keypad are identical to those at the top of the remote control,
and are described on the following pages.
Projector status indicators
The indicators on the control panel are as follows:
Poweroff = NO POWER
green = normal RUNNING modeamber = STANDBY mode
Shutteryellow = CLOSEDgreen = OPEN
Erroroff = NO ERROR
flashing = ERROR...