Digital Projection Titan Sx+-500 User Manual

Rev B          02/2007        page 4.19
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
For more information about
input modes and input presets,
see earlier in this section, Input
modes and settings.
Input Menu
Presets
Input Menu
Presets
Recall Preset s A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters
saved for each Preset are:
all...

Rev B          02/2007         page 4.20
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
Input Menu
Presets
Save Presets A ~ H Save Presets
•Press  and   to select Save Preset.
Press 
 to open the Save Presets A  ~ H submenu.
• To save the current set of parameters, press 
 and   to select one of the
Presets.
For Presets J to S, select Save Preset J ~ S then press 
 to open...

Rev B          02/2007        page 4.21
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When using the menus, press
OSD 
 or  to hide or
reveal the On-Screen-Display.
Picture Menu
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
The Saturation slider is
available for Composite, S-
Video and...

Rev B          02/2007         page 4.22
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
For more information about
User gamma settings, see
Section 5. DP Userware.
Parametric Gamma adjustment
is available only when
Parametric is selected in
Gamma selection, above.
Phase adjustment can be found
in both the Picture and
Geometry menus, and is
available for graphics based
RGB sources only.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied....

Rev B          02/2007        page 4.23
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Aspect Ratio selection can be
found in both the Picture and
Geometry menus.
When User Aspect is selected,
the Aspect Ratio needs to be
set in the Geometry menu.
The Sharpness slider is
available for Composite, S-
Video and Component SD
inputs only.
Aspect Ratio
•Press  and   to select Aspect Ratio.
Press 
 and   to select from:
FillThis will best fit the incoming source to fill either...

Rev B          02/2007         page 4.24
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When using the menus, press
OSD 
 or  to hide or
reveal the On-Screen-Display.
Geometry Menu
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Aspect Ratio selection can be
found in both the Picture and...

Rev B          02/2007        page 4.25
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Horizontal and Vertical
Aspect Ratio adjustments are
available only when User is
selected in Aspect Ratio, (see
previous page).
Keystone adjustment can be
found in both the Geometry and
Projector Setup menus.
Phase adjustment can be found
in both the Picture and
Geometry menus, and is
available for graphics based
RGB sources only.
Pixels adjustment  is available
for graphics based RGB...

Rev B          02/2007         page 4.26
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Blanking
Blanking curtains can be applied to each edge of the picture.
•Press 
 and   to select Blanking.
Press 
 to open the Blanking submenu.
Blanking On/Off
Press  and   to select from:
On
Off
Blanking adjust
•Press  and   to select the edge to be Blanked.
Press 
 and   to adjust the slider (0 to 200).
Notes
Geometry Menu
Blanking
The blanking curtains will not
applied until Blanking is...

Rev B          02/2007        page 4.27
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
When using the menus, press
OSD 
 or  to hide or
reveal the On-Screen-Display.
Colour Menu
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Read these notes on Colour
and Global Colourimetry
before making any settings in
the Colour menus.
Colour menu
To return to the main menu, press  up to three...

Rev B          02/2007         page 4.28
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
Read the notes on Colour and
Global Colourimetry earlier in
this section before making
any settings in the Colour
menus.
The Colour Temperature slider
is available  only if
Temperature Mode is selected.
The RGB Lift and Gain sliders
are available  only if User Mode
is selected.
The Component Type
selection is available  for RGB1,
RGB2 and Component  inputs
only.
Colour Mode
•Press  and...