Digital Projection Titan Sx+-500 User Manual

Rev B          02/2007       page 2.11
Digital Projection TITAN sx+-500 User Manual2. Installation
Notes
For more information on using
the Lens shift feature, see
section 4. Using the menus,
Lens menu.
If the lens is to be shifted in two
directions combined, the
maximum range is somewhat
less, as can be seen below.
full horizontal and vertical shift
without distortion
combined shift without distortion
is reduced
total lens mount shift available
Shifting the image
The normal position for the projector is...

Rev B          02/2007      page 2.12
2. InstallationDigital Projection TITAN sx+-500 User Manual
Notes
BEFORE INSTALLING THE
PROJECTOR, READ ALL THE
WARNINGS BELOW AND ALL
THOSE IN IMPORTANT
INFORMATION AT THE
FRONT OF THIS MANUAL.
The projector weighs
approximately 27kg (60lbs).
Use safe handling techniques
when lifting the projector.
Make sure that the surface,
ceiling or rigging that is to
support the projector is
capable of supporting the
combined weight of the
projector and lens (see
specification...

Rev B          02/2007       page 2.13
Digital Projection TITAN sx+-500 User Manual2. Installation
Adjusting the rigging frame
Coarse adjustment of projector level should be made by adjusting the length of the
supporting wires or chains, or by adjusting the position of the truss or rigging. Once
the initial coarse adjustment has been made, fine adjustment can be made by
turning the frame adjusters on the rigging frame:
•The single vertical adjuster at the front left corner is used to
raise or lower the...

Rev B          02/2007      page 2.14
2. InstallationDigital Projection TITAN sx+-500 User Manual
Notes
When stacking projectors, the
stack MUST be vertical, to
ensure that the stresses are
distributed to all frame
couplings.
Make sure that the surface,
ceiling or rigging that is to
support the projector is
capable of supporting the
combined weight of all the
projectors and lenses (see
specification for weights ).
Do not place heavy objects
on top of the projector
chassis. Only the chassis
corners and...

Rev B          02/2007       page 2.15
Digital Projection TITAN sx+-500 User Manual2. Installation
Notes
For more information on
selecting an input source, see
section 4. Overview, Using
the control keys, and Using
the menus.
For more information about pin
connections and control codes
see section 7. Appendix.
For more information on input
modes see section
4. Overview.
Input
connection panelControl
connection panel
Connecting the projector
Signal Inputs
The following inputs are available:
EDID...

Rev B          02/2007      page 2.16
2. InstallationDigital Projection TITAN sx+-500 User Manual
Notes
For more information about pin
connections and control codes
see section 7. Appendix.
For more information about
using a browser to control the
projector see section 4. Using
the menus.Crossed
LAN cableTITAN
Computer
Un-crossed
LAN cablesComputer
TITAN TITAN Hub or
LAN
ComputerNull-modem
cableTITAN
Control connection examples
LAN connection
All of the projector’s features can be controlled via a LAN...

Rev B          02/2007       page 2.17
Digital Projection TITAN sx+-500 User Manual2. Installation
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a Ground
connection, as this
equipment MUST be earthed.
Handle the power cable
carefully and avoid sharp
bends. Do not use a damaged
power cable.
Power connection
When mains power is first applied, the projector will perform a self-test, then go into
Standby mode.
The Power indicator on the control panel will show amber until the...

Rev B          02/2007      page 2.18
2. InstallationDigital Projection TITAN sx+-500 User Manual 

Rev B          02/2007
3. Getting started
Contents
3. Getting started 3.1
Switching the projector on .....................................................................................................3.2
Selecting an input or test pattern.......................................................................................... 3.2
Input................................................................................................................................................................. 3.2...

Rev B          02/2007         page 3.2 3. Getting startedDigital Projection 
TITAN sx+-500 User Manual
Selecting an input or test patter n
Input
•Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
•Or press the numbered keys 1–7 to change directly to the input:
If you have no video source connected to the projector, then you can display a test
pattern as follows:
•Press 
 on the remote control, to select a test...